|
Title: Antminer S3+ support Post by: bodaboda on December 12, 2015, 03:04:16 PM Hey guys!
I've some questions and I hope someone can give me an answer and help me. My Antminer S3+ is beeing powered with a Corsair RM850 and working 218@stock voltage whitch gives me an avg 440 (0% HW errors). I tried some new settings like 225 and 250 but i got some HW errors (0.043%) and the same hash rates that i got at 218. I tried different firmwares and kano's cgminer but i got the same results. Does someone have a possible explanation for this? :) (maybe a batch 1?) Best regards btw: kano's cgminer sometimes reports 700+GH/s, is this normal? Title: Re: Antminer S3+ support Post by: sgi02 on December 12, 2015, 09:08:02 PM How long did you give the unit to see your average hashrate? On my S3's it takes about 30mins / 1HR for it to stabilize. Your HW errors seem perfectly reasonable, even at stock its not uncommon to get some HW errors here and there. Id say bump it to 237.5mhz, let it run for an hour, take a screenshot of your miner status page and post back.
Title: Re: Antminer S3+ support Post by: VirosaGITS on December 12, 2015, 10:00:44 PM Hey guys! I've some questions and I hope someone can give me an answer and help me. My Antminer S3+ is beeing powered with a Corsair RM850 and working 218@stock voltage whitch gives me an avg 440 (0% HW errors). I tried some new settings like 225 and 250 but i got some HW errors (0.043%) and the same hash rates that i got at 218. I tried different firmwares and kano's cgminer but i got the same results. Does someone have a possible explanation for this? :) (maybe a batch 1?) Best regards btw: kano's cgminer sometimes reports 700+GH/s, is this normal? I would check the voltage at the Miner's PCI-e plug. Some S3's are simply icky, they dont clock well, but either way, the reason why you can not bring it to 500 is its not getting the voltage it wants. Some are better than other as in they can go higher with the same stock voltage. But some PSU's voltage output drop under load, which worsen the condition. (btw) Also yes, variance is normal. Title: Re: Antminer S3+ support Post by: notlist3d on December 13, 2015, 04:53:15 AM How long did you give the unit to see your average hashrate? On my S3's it takes about 30mins / 1HR for it to stabilize. Your HW errors seem perfectly reasonable, even at stock its not uncommon to get some HW errors here and there. Id say bump it to 237.5mhz, let it run for an hour, take a screenshot of your miner status page and post back. I would agree on running for 30 to hour before getting stats. That 700+ is not true on one S3+ even. As far as first post the batch one problems were on regular S3's. So they do not have the S3+ label. If you have that label you are not having the issues that batch went throught. It was just batch one of S3's. A lot just ran under spec. Some ran perfect at spec. Just did not know till your ran it. Title: Re: Antminer S3+ support Post by: bodaboda on December 14, 2015, 06:56:55 PM https://i.imgur.com/jsZpbG7.png
A print from my S3+, currently 250@0.780v. This amount HW errors is acceptable or not? Thanks for helping me guys :) Title: Re: Antminer S3+ support Post by: RichBC on December 14, 2015, 08:39:45 PM https://i.imgur.com/jsZpbG7.png A print from my S3+, currently 250@0.780v. This amount HW errors is acceptable or not? Thanks for helping me guys :) Looks good to me, all the ASIC's are OK, temperature looks good. 250MHz is a small overclock and HW error rate of 0.0297 is acceptable. The 0.78V however means nothing as it is not adjustable. Rich Title: Re: Antminer S3+ support Post by: bodaboda on December 14, 2015, 08:46:50 PM The 0.78V however means nothing as it is not adjustable. I didn't understand this part =P Title: Re: Antminer S3+ support Post by: VirosaGITS on December 14, 2015, 09:07:34 PM The 0.78V however means nothing as it is not adjustable. I didn't understand this part =P He means the value you set for volt does not actually do anything. Volt on the S3 is not adjustable. You can set a value, but there is nothing to pass it to, therefore the 0.78V setting means nothing. Title: Re: Antminer S3+ support Post by: bodaboda on December 14, 2015, 09:55:49 PM The 0.78V however means nothing as it is not adjustable. I didn't understand this part =P He means the value you set for volt does not actually do anything. Volt on the S3 is not adjustable. You can set a value, but there is nothing to pass it to, therefore the 0.78V setting means nothing. Hmm i thought that if i set a value that would do something. Are you sure that in S3+ is not possible to raise voltage? I'm asking because there are some threads about OC in this machines. How can i check if this unit is capable of it? btw sorry for my english =P Title: Re: Antminer S3+ support Post by: RichBC on December 14, 2015, 10:10:16 PM The 0.78V however means nothing as it is not adjustable. I didn't understand this part =P He means the value you set for volt does not actually do anything. Volt on the S3 is not adjustable. You can set a value, but there is nothing to pass it to, therefore the 0.78V setting means nothing. Hmm i thought that if i set a value that would do something. Are you sure that in S3+ is not possible to raise voltage? I'm asking because there are some threads about OC in this machines. How can i check if this unit is capable of it? btw sorry for my english =P Yes quite sure. The only way to raise the voltage is to change a resistor value on the potential Divider from the Buck Converter chips. (pencil Mod). You do not have to overvolt to overclock, some overclocking will be possible at the standard core voltage, limited by when the HW error rate get's much above 0.05%,and the hash Rate begins to drop below what is expected. Rich Title: Re: Antminer S3+ support Post by: bodaboda on December 15, 2015, 12:54:37 PM The 0.78V however means nothing as it is not adjustable. I didn't understand this part =P He means the value you set for volt does not actually do anything. Volt on the S3 is not adjustable. You can set a value, but there is nothing to pass it to, therefore the 0.78V setting means nothing. Hmm i thought that if i set a value that would do something. Are you sure that in S3+ is not possible to raise voltage? I'm asking because there are some threads about OC in this machines. How can i check if this unit is capable of it? btw sorry for my english =P Yes quite sure. The only way to raise the voltage is to change a resistor value on the potential Divider from the Buck Converter chips. (pencil Mod). You do not have to overvolt to overclock, some overclocking will be possible at the standard core voltage, limited by when the HW error rate get's much above 0.05%,and the hash Rate begins to drop below what is expected. Rich Is there any scheme for pencil mod? My hash dropped to 460 avg after 10 hours running, maybe this unit can't handle 250mhz =P Title: Re: Antminer S3+ support Post by: RichBC on December 15, 2015, 01:03:52 PM Is there any scheme for pencil mod? My hash dropped to 460 avg after 10 hours running, maybe this unit can't handle 250mhz =P Details on how to pencil mod will be in this thread somewhere, here is a picture I put up showing which resistors to modify. The pencil mod is usually used to reduce the voltage on the Core for better efficiency when underclocking. However by pencil modding a different resistor you can also increse the core voltage to support overclocking. http://www.slotforum.com/forums/uploads/1446458284/gallery_2150_2322_162967.jpg (http://www.slotforum.com/forums/index.php?autocom=gallery&req=si&img=78906) Red lines indicate the resistors to mod for Undervolting. Green Lines for Overvolting. Rich Rich Title: Re: Antminer S3+ support Post by: bodaboda on December 15, 2015, 01:12:24 PM Thanks Rich! :D
I dont have a voltimeter with me right now, need to wait a few days before testing this.. How much did you achive with this? Title: Re: Antminer S3+ support Post by: RichBC on December 15, 2015, 01:23:12 PM Thanks Rich! :D I dont have a voltimeter with me right now, need to wait a few days before testing this.. How much did you achive with this? I only ever tried Undervolting as back then BTC was much lower and I needed greater efficiency, so cannot speak for Overvolting. This is what I managed undervolting. Code: MHz V Core GH W J/GH Rich Title: Re: Antminer S3+ support Post by: bodaboda on December 15, 2015, 05:41:03 PM I tried the mod but it didnt work, after a hour or two, hash drops to 470/460. And yes, i modded the "red" resistors =P
Title: Re: Antminer S3+ support Post by: RichBC on December 15, 2015, 05:59:09 PM I tried the mod but it didnt work, after a hour or two, hash drops to 470/460. And yes, i modded the "red" resistors =P If you were able to achieve an overclock to 470/460 having adjusted the "Red" resistors to Undervolt then you did very well. Rich Title: Re: Antminer S3+ support Post by: bodaboda on December 15, 2015, 06:41:31 PM I tried the mod but it didnt work, after a hour or two, hash drops to 470/460. And yes, i modded the "red" resistors =P If you were able to achieve an overclock to 470/460 having adjusted the "Red" resistors to Undervolt then you did very well. Rich F*ck, I mean Green. Sorry :) Title: Re: Antminer S3+ support Post by: Srheal on December 17, 2015, 09:06:33 PM I got a question about mining I want too litecoin mine using better quality mining speeds, with a limited purchase of equipment so can I use these two miners to mine lite-coins Avalon Nano 3 Newest USB 3.6Gh/s Asic Bitcoin Miner. Or lets say i purchase a bitmain s3 Antminer can i use it to mine lite-coins. and if not why and can't I, can some one explain if we are restricted or what are the barriers that block me from using faster equipment to get the most of our mining capabilities.
Thanks link is posted: http://www.amazon.com/Avalon-Newest-3-6Gh-Bitcoin-Miner/dp/B00Q8G3BLK/ref=sr_1_fkmr1_2?s=pc&ie=UTF8&qid=1450383549&sr=1-2-fkmr1&keywords=bi+fury+miner Title: Re: Antminer S3+ support Post by: RichBC on December 17, 2015, 09:13:45 PM I got a question about mining I want too litecoin mine using better quality mining speeds, with a limited purchase of equipment so can I use these two miners to mine lite-coins Avalon Nano 3 Newest USB 3.6Gh/s Asic Bitcoin Miner. Or lets say i purchase a bitmain s3 Antminer can i use it to mine lite-coins. and if not why and can't I, can some one explain if we are restricted or what are the barriers that block me from using faster equipment to get the most of our mining capabilities. Thanks link is posted: http://www.amazon.com/Avalon-Newest-3-6Gh-Bitcoin-Miner/dp/B00Q8G3BLK/ref=sr_1_fkmr1_2?s=pc&ie=UTF8&qid=1450383549&sr=1-2-fkmr1&keywords=bi+fury+miner This is the S3+ Support thread. S3+ only Mines Bitcoin, they cannot mine Litecoin. Please move your question in the Alt Coins Section. Rich |
