|
Title: [WTS] ASICMINER Prisma 1.0 Boards ($5/board) - 300-360gh/s Post by: CrazyGuy on December 16, 2015, 01:59:01 AM I have a good amount of returned ASICMINER Prisma 1.0 boards that I'm willing to sell for $15 a piece. Each board should be capable of operating at 300-360gh/s using .8-.9 watts per gh.
https://i.imgur.com/2gT7pZCl.jpg (http://imgur.com/2gT7pZC) Data cable included. No heatsinks included. Minimum purchase of 2 boards required. Shipping costs covered by buyer. 8 should fit in a Medium or Region B box. IMPORTANT NOTE: These boards are all returns from the ASICMINER Prisma return program last year. ASICMINER offered a full refund or replacement to all buyers as there were multiple reports of Prismas catching on FIRE. There are no temperature sensors on the Prisma boards and things tend to go bad if a chip went out and you are using a PSU with no overvoltage protection. Because of this, I take no responsibility for any damage caused by malfunctioning boards. Do not run them near flammable objects! They are also being sold without warranty or support. The boards I will ship out have been marked as running without issue by the original buyers, but I have no way to test them. With that said, I managed to personally run 8 Prisma 1.0 units for 4 months without issue. Sidehack ran a good amount of them as well. My personal units were run in an area with adequate cooling, and with a good amount of airflow on the outside of the boards. I also did not run them near anything flammable, just in case... Controllers I've got a good amount of Prisma 1.0 controllers and usb to uart adapters available if needed. $15 and $10 respectively. Current Stock. Prices per unit $5 - "Failing" Boards - $10 - UART to USB Adapter - $15 - Prisma 1.0 BE Controller - $15 - Prisma 2.0 BE Controller - 2 left Shipping info: Shipping from US zip code 75013 8 Prisma boards will fit in a Medium flat box, which will cost $11.30 to ship. Region B boxes can be cheaper ($8-$13), depending on your location. Please calculate your shipping costs below: http://postcalc.usps.gov/ Payment: Please use coinbase rate to determine your payment amount. Pay to the following address: Payment Address: 1EbmRs3iBGcKJPoprSa4Vqkat6HizqgGet (bitcoin:1EbmRs3iBGcKJPoprSa4Vqkat6HizqgGet?label=Prisma%20Boards) Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($15/board) - 300-360gh/s Post by: J4bberwock on December 16, 2015, 11:14:41 AM I have a good amount of returned ASICMINER Prisma 1.0 boards that I'm willing to sell for $15 a piece. Each board should be capable of operating at 300-360gh/s using .8-.9 watts per gh. No heatsinks included. Minimum purchase of 2 boards required. Shipping costs covered by buyer. 8 should fit in a Region B box. IMPORTANT NOTE: These boards are all returns from the ASICMINER Prisma return program last year. ASICMINER offered a full refund or replacement to all buyers as there were multiple reports of Prismas catching on FIRE. There are no temperature sensors on the Prisma boards and things tend to go bad if a chip went out and you are using a PSU with no overvoltage protection. Because of this, I take no responsibility for any damage caused by malfunctioning boards. Do not run them near flammable objects! They are also being sold without warranty or support. The boards I will ship out have been marked as running without issue by the original buyers, but I have no way to test them. With that said, I managed to personally run 8 Prisma 1.0 units for 4 months without issue. Sidehack ran a good amount of them as well. My personal units were run in an area with adequate cooling, and with a good amount of airflow on the outside of the boards. I also did not run them near anything flammable, just in case... Controllers I've got a good amount of Prisma 1.0 controllers and usb to uart adapters available if needed. $15 and $10 respectively. Can you give me a good price for 40-60 of them including shipping to France ? I may have a small project in which they could have some use. I could use a second batch of 60 later if it works as expected. Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($15/board) - 300-360gh/s Post by: herzlos1985 on December 16, 2015, 04:35:32 PM you sell https://asicpuppy.com (https://asicpuppy.com) with shipping turkey.buy 4pcs/lot and prisma controler...
Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($15/board) - 300-360gh/s Post by: CrazyGuy on December 16, 2015, 04:46:15 PM I have a good amount of returned ASICMINER Prisma 1.0 boards that I'm willing to sell for $15 a piece. Each board should be capable of operating at 300-360gh/s using .8-.9 watts per gh. No heatsinks included. Minimum purchase of 2 boards required. Shipping costs covered by buyer. 8 should fit in a Region B box. IMPORTANT NOTE: These boards are all returns from the ASICMINER Prisma return program last year. ASICMINER offered a full refund or replacement to all buyers as there were multiple reports of Prismas catching on FIRE. There are no temperature sensors on the Prisma boards and things tend to go bad if a chip went out and you are using a PSU with no overvoltage protection. Because of this, I take no responsibility for any damage caused by malfunctioning boards. Do not run them near flammable objects! They are also being sold without warranty or support. The boards I will ship out have been marked as running without issue by the original buyers, but I have no way to test them. With that said, I managed to personally run 8 Prisma 1.0 units for 4 months without issue. Sidehack ran a good amount of them as well. My personal units were run in an area with adequate cooling, and with a good amount of airflow on the outside of the boards. I also did not run them near anything flammable, just in case... Controllers I've got a good amount of Prisma 1.0 controllers and usb to uart adapters available if needed. $15 and $10 respectively. Can you give me a good price for 40-60 of them including shipping to France ? I may have a small project in which they could have some use. I could use a second batch of 60 later if it works as expected. Do you care if they are marked as working or not? There are a few that were marked as not working, which could be due to a single bad component. I can sell those for $10 a piece. Also, if you buy 40-60, I'll ship for free Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($15/board) - 300-360gh/s Post by: CrazyGuy on December 16, 2015, 04:47:28 PM you sell https://asicpuppy.com (https://asicpuppy.com) with shipping turkey.buy 4pcs/lot and prisma controler... I don't have them listed on the site, but I'll ship anywhere, as long as you are willing to pay the shipping costs. Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($15/board) - 300-360gh/s Post by: herzlos1985 on December 16, 2015, 04:52:45 PM Estimate shipping fee Turkey 31200...
Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($15/board) - 300-360gh/s Post by: J4bberwock on December 16, 2015, 05:29:36 PM I have a good amount of returned ASICMINER Prisma 1.0 boards that I'm willing to sell for $15 a piece. Each board should be capable of operating at 300-360gh/s using .8-.9 watts per gh. No heatsinks included. Minimum purchase of 2 boards required. Shipping costs covered by buyer. 8 should fit in a Region B box. IMPORTANT NOTE: These boards are all returns from the ASICMINER Prisma return program last year. ASICMINER offered a full refund or replacement to all buyers as there were multiple reports of Prismas catching on FIRE. There are no temperature sensors on the Prisma boards and things tend to go bad if a chip went out and you are using a PSU with no overvoltage protection. Because of this, I take no responsibility for any damage caused by malfunctioning boards. Do not run them near flammable objects! They are also being sold without warranty or support. The boards I will ship out have been marked as running without issue by the original buyers, but I have no way to test them. With that said, I managed to personally run 8 Prisma 1.0 units for 4 months without issue. Sidehack ran a good amount of them as well. My personal units were run in an area with adequate cooling, and with a good amount of airflow on the outside of the boards. I also did not run them near anything flammable, just in case... Controllers I've got a good amount of Prisma 1.0 controllers and usb to uart adapters available if needed. $15 and $10 respectively. Can you give me a good price for 40-60 of them including shipping to France ? I may have a small project in which they could have some use. I could use a second batch of 60 later if it works as expected. Do you care if they are marked as working or not? There are a few that were marked as not working, which could be due to a single bad component. I can sell those for $10 a piece. Also, if you buy 40-60, I'll ship for free You can add the "non working" ones, as long as I have at least 40 working ones, give me a total, I'll send BTC right away and give you the shipping address. Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($15/board) - 300-360gh/s Post by: CrazyGuy on December 17, 2015, 06:43:18 AM I've taken inventory of all boards/components and updated the first post. Shipping and payment info updated as well.
Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($15/board) - 300-360gh/s Post by: baldpope on December 17, 2015, 08:36:49 PM What are the differences between the 1.0 and 2.0 controllers?
Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($15/board) - 300-360gh/s Post by: CrazyGuy on December 17, 2015, 08:42:07 PM What are the differences between the 1.0 and 2.0 controllers? 1.0 controller is only compatible with Prisma 1.0, and 2.0 controller is only compatible with Prisma 2.0. I should have clarified this. I put the 2.0 controllers up there in case someone needs one. Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($15/board) - 300-360gh/s Post by: CrazyGuy on December 18, 2015, 05:42:23 AM 60 boards went out today. More going out tomorrow. Updated total boards left.
Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($15/board) - 300-360gh/s Post by: CrazyGuy on December 20, 2015, 02:35:50 PM The last 35 passing boards have been sold. A good majority of the bad boards were from a poorly packaged return shipment, with the only problem I could see being bent fan headers. I may have an opportunity to test some of those boards this week and possibly move them to the "passing" column.
Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($15/board) - 300-360gh/s Post by: Sweminer777 on December 20, 2015, 03:29:28 PM this are supposed to work how many controllers per board is needed? vice versa.
i might intereseted in about 10ths , maybe to much?. what heatsinks would fit ? Pm me for more details. my electricity is very cheap, at this pricez it is intereseting . regards Title: Re: [WTS] ASICMINER Prisma 1.0 Boards ($5/board) - 300-360gh/s Post by: CrazyGuy on April 09, 2016, 03:44:02 PM I've lowered the price to $5 per board for the remaining 28 Prisma boards. I've marked these boards as failing but most were just poorly packaged for return shipment. Bent fan headers and missing caps on a few of the boards but I suspect a lot of them are working.
Please refer to the first post for all shipping related questions |
