Bitcoin Forum

Hi

i changed ma mainboard from any old Asus to ASRock H81 PRO BTC R2.0

same Windows7 same GPU. Before with old mainboard everything was ok, Claymoreminer worked perfect.

Now it crash always at the line :

POOL/SOLO version

What happens ?

I am using not the newest version of claymore, on the both last versions is a trojan

Peter

I assume youve sorted out any problems with windows that are caused when switching mobos?

Did you create a new .bat file for the new v10.0 Claymore? I do it just as a matter of course.

Where can I get the new version of Claymore?
here
https://drive.google.com/drive/folders/0B69wv2iqszefdFZUV2toUG5HdlU

and here
https://mega.nz/#F!O4YA2JgD!n2b4iSHQDruEsYUvTQP5_w

is a virus

DOWNLOAD FROM HERE (https://bitcointalk.org/index.php?topic=1433925.0)
This is the official forum page .
its not a virus , if you say its a virus could you give us some prove ?
if the only reason you telling us its a virus , just bc your antivirus software telling you its a virus  , then do your own research  ;D

So you ignore my first question and keep saying its a virus. Its not a virus. Ive had three versions of claymore and none of them have triggered virus software. If they ever did i would just add it to the exceptions list.

OK, I uninstalled Norton and then I was able to download the last version of Claymore miner.

I used the same bat file to start it as before (this is running already on my 2 other PCs) and also created a new bat file
but the problem ramains

when POOL/SOLO version apears the exe crash - the message is that exe doesn't work anymore

What can I do? How to debug?

I think windows should be ok, device manager shows everything ok.

The miner app shows that the GPU was found Sapphire RX 480 and than finish

I dismaunted also a GPU from an other PC (which is working/mining well) an put it to tis one with ASrock mainbord, same problem.

Should I set somethin on BIOS?

can be a higher intensity (-i 26) etc.

How much oc done by you? I think it is hanging in loading dag file.
 ok add -lidag 1 in batch file of mining program.
low intensity mode while loading dag at starting of mining program 


-lidag   low intensity mode for DAG generation, it can help with OC or weak PSU. Supported values are 0, 1, 2, 3, more value means lower intensity. Example: "-lidag 1".
   You can also specify values for every card, for example "-lidag 1,0,3". Default value is "0" (no low intensity for DAG generation).

what is dc ?

I tried "-lidag 1" to 9 but no changes

Some idea: is there a minimum limit of RAM memory?
I installed only 2x 1GB RAMs, is this maybe the problem?

Have you changed virtual memory to more than 16gb  oh shit minimum ram required is 4GB

https://Buy this if your board supports ddr4 and 2133 freq
There is a minimum limt of 4GB of ram and 16GB of virtual memory

www.amazon.com/Corsair-Memory-Module-2133MHz-Unbuffered/dp/B0143UM5YQ

OK, now we are on the right way  ;)

ALL THE BEST DUDE

IT WORKS  :D :D

with 4GB

But now there is an othher problem. Using 3 GPUs all of them are working, as long as I put the next one - nothing works.

All GPUs are in dev. manager -OK
Claymore shows also 4 GPUs
but then there is an error: cannot create DAG on GPU
GPU 1 failed

then same restart, and next time GPU 3 failed, next time 2  or again 1.

Are even 4GB not enought for  4 GPUs?

4 GB is enough for 4 GPU : that's what I used

I would think of a PSU problem : are you sure your GPU / risers / motherboard are correctly powered ? Did you plug the molex on your Asrock ?

Both molex are connected. The PSU has 800W, should be also enough. 4 GPUs should take max 600W

I have no idea whats the problem. I played also with virtual memory, set it to: min: 16384 MB to 32768 MB but with this setting my hashrate was reduced from 22 MH/s to 18 MH/s, so I put back windows standard setting.

Have you enabled above 4G decoding?

No, what is it? How to do?

In the UEFI/BIOS settings go through all the sections and find "Above 4G Decoding" and Enable it.