|
Title: SOLO Mining HELP Post by: opies32765 on September 28, 2017, 02:40:53 PM Guys,
Need some HELP Trying to mine UBIQ SOLO.... set up 1st computer with the node...even connect a miner on that same computer to the node with no issues... trying to connect other computers on the same local network to the node...using the first computers IP address 192.168.1.54:8588 using claymore im getting ETH: http error #7. ETH: Failed to connect to pool (192.168.1.54:8588), retry in 20 sec... has anyone seen this before ? I even opened a firewall rule with the 8588 port Thanks in advance Title: Re: SOLO Mining HELP Post by: Ayers on September 28, 2017, 03:05:11 PM you need to allow the program via the firewall not just opening the port "allow a program through windows firewall..." etc and on config file you need to add rpcallowip=192.168.1.*
Title: Re: SOLO Mining HELP Post by: opies32765 on September 28, 2017, 04:21:29 PM Ayers
so as below ? Im assuming the allow ip is to the remote computer trying to connect ? Thanks in advance # WARNING! Remove "#" characters to enable lines, with "#" they are disabled and will be ignored by miner! Check README for details. # WARNING! Miner loads options from this file only if there are not any options in the command line! -epool http://192.168.1.54:8588 -ewal 0x926957F22b01b2E100078DF71Cf33377E0b0C9a9 -epsw x #-dpool stratum+tcp://yiimp.ccminer.org:4252 #-dwal DsUt9QagrYLvSkJHXCvhfiZHKafVtzd7Sq4 #-dpsw x #-esm 1 -mode 1 #-tt 70 #-asm 0 -rpcallowip=192.168.1.37 Title: Re: SOLO Mining HELP Post by: makomako on September 28, 2017, 05:58:39 PM Ayers so as below ? Im assuming the allow ip is to the remote computer trying to connect ? Thanks in advance # WARNING! Remove "#" characters to enable lines, with "#" they are disabled and will be ignored by miner! Check README for details. # WARNING! Miner loads options from this file only if there are not any options in the command line! -epool http://192.168.1.54:8588 -ewal 0x926957F22b01b2E100078DF71Cf33377E0b0C9a9 -epsw x #-dpool stratum+tcp://yiimp.ccminer.org:4252 #-dwal DsUt9QagrYLvSkJHXCvhfiZHKafVtzd7Sq4 #-dpsw x #-esm 1 -mode 1 #-tt 70 #-asm 0 -rpcallowip=192.168.1.37 Not on your bat file, add the -rpcallowip on your wallets conf file. make sure your rpc port and other details are the same with your config file Title: Re: SOLO Mining HELP Post by: salmanahmedone on October 04, 2017, 11:35:47 PM Guys, Need some HELP Trying to mine UBIQ SOLO.... set up 1st computer with the node...even connect a miner on that same computer to the node with no issues... trying to connect other computers on the same local network to the node...using the first computers IP address 192.168.1.54:8588 using claymore im getting ETH: http error #7. ETH: Failed to connect to pool (192.168.1.54:8588), retry in 20 sec... has anyone seen this before ? I even opened a firewall rule with the 8588 port Thanks in advance It's not something that you really need to worry about it. If you're insistent on selling just do it through the wallet of the coin by simply setting your generate true. That's the easiest way to sell them at that method right there is not going to be any worse than pointing some other Miner at that coin. |