|
Title: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on November 10, 2017, 11:19:34 AM Here's the issue you may have , hashboards are not recognized, anymore
https://img15.hostingpics.net/pics/396492403293Screenshot201711101152151.jpg /!\ please read carefuly /!\ ************************************************************** Firmware Flash ************************************************************** Here's a fix solution to rewite PIC's of L3+ after some of us flash bad firmware to their L3+. Many has recovered 3 boards , some all of it Thanks to Blissz for this fix (please do not pm him for this ) 1. Download File (re-up) Quote WARNING: Don't flash this to anything else as a bricked L3(+) caused by flashing a wrong firmware version, as this might harm a working L3(+). MEGA (https://mega.nz/#!8zwzGbRB!ImyUOtfpZbEo9E4DDnJv5M8ejXXVyh-2rjGsMfUYKQU) or 1fichier (https://1fichier.com/?rl6jg4941p) 2. Plug only 1 board from chain 0 (white cable on the left) as you can see under , you can plug upper hashboard 1st https://img15.hostingpics.net/pics/67636520171209112922.jpg 3. Go to system -> Upgrade -> "Flash new firmware image" choose the file downloaded to flash new firmware and click flash image wait for reboot. If kernel logs get this ... 0xcc , wait after you see it (5 minutes, to see again 0xcc or most of time 0x3 and then it will fix your board) other way try to connect an other boards and restart from "3" Quote Dec 17 14:09:30 (none) local0.warn cgminer: Started cgminer 4.9.0 Dec 17 14:09:30 (none) local0.notice cgminer[377]: detected at /sys/class/gpio/gpio51/value chain 0 Dec 17 14:09:30 (none) local0.notice cgminer[377]: detect total chain num 1 Dec 17 14:09:30 (none) local0.notice cgminer[377]: i2c init ok Dec 17 14:09:32 (none) local0.notice cgminer[377]: Chain 0 PIC Version 0xcc Dec 17 14:13:45 (none) local0.err cgminer[377]: Blisssz: Chain not found 1 Dec 17 14:13:45 (none) local0.err cgminer[377]: Blisssz: Chain not found 2 Dec 17 14:13:45 (none) local0.err cgminer[377]: Blisssz: Chain not found 3 Dec 17 14:13:51 (none) local0.notice cgminer[377]: Chain 0 PIC Version 0x3 [...] you will see some logs like this , PIC's is currently writing. Code: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] wait logs "miner start and switching pool" the board has been flashed with success. After fixing all or some of boards , you can finaly flash back bitmain l3+ original Firmware. (https://s3.cn-north-1.amazonaws.com.cn/shop-bitmain/download/Antminer-L3%2B-201708251737-384M.tar.gz) ************************************************************** Manually Flash ************************************************************** /!\ I will not assist with "how to" here cause i didnt experience it yet but if you have stuff (pickit3) and knowledge to manually flash chip of your miner here's the files ! warning ! have a look to the pic version you have (writed on the chip). there is PIC16F1704 or PIC16F1705 Here's the hexa files for each version MEGA PIC16F1704.hex (https://mega.nz/#!oEMByRqB!hm-s2VgoDe_jVEIRgECbHG0V2bLCujCAkOhXhJrswUc) PIC16F1705.hex (https://mega.nz/#!tQMCTZBS!n80UvNH-7fw1zQVjkBsRvIM_fA_0IBA9ikjVCMOFGK0) 1FICHIER PIC16F1704.hex (https://1fichier.com/?0am7he0kt8) PIC16F1705.hex (https://1fichier.com/?22xhc0iu36) Thanks to martin_fryc for sharing files, after succefully fix his L3+ by manually flashing PICs ************************************************************** Title: Re: Issue new antminer l3+ Post by: omshree on November 10, 2017, 03:53:35 PM How did you get this error? Did you flashed fw before that?
Title: Re: Issue new antminer l3+ Post by: Bulletdodger on November 11, 2017, 12:43:37 PM Weird, havent seen it before. :/
Title: Re: Issue new antminer l3+ Post by: omshree on November 11, 2017, 09:53:18 PM Had the same issue, you have to write the PIC controller manually, extracting the working hexa file from a working hashboard, needs to be done with special chip reader tools.
Title: Re: Issue new antminer l3+ Post by: cryptonitro on November 20, 2017, 12:25:49 PM Had the same issue, you have to write the PIC controller manually, extracting the working hexa file from a working hashboard, needs to be done with special chip reader tools. hi thanks for answers how can i do that if boards are not recognized ? if you have that error ? may be you have file and how to ? yeah i flash before have that , may be something went wrong. i changed control board , nothing better i have only blackcat usb at this time capable to flash , but its for jtag Title: Re: Issue new antminer l3+ Post by: blissz on November 20, 2017, 08:54:29 PM I am pretty sure it's indeed the pic on each mining board that needs to be reprogrammed. Very annoying. :(
What you can try: https://shop.bitmain.com/support.htm?pid=007201604120945219855QObfk20066C flash this image to a micro sd card (with win32diskimager) and boot that image. Then check the kernel log. Then flash again the l3 image from there and see if it helps. It might force flashing the pic's on the hashing boards. Title: Re: Issue new antminer l3+ Post by: cryptonitro on November 21, 2017, 12:22:36 AM I am pretty sure it's indeed the pic on each mining board that needs to be reprogrammed. Very annoying. :( What you can try: https://shop.bitmain.com/support.htm?pid=007201604120945219855QObfk20066C flash this image to a micro sd card (with win32diskimager) and boot that image. Then check the kernel log. Then flash again the l3 image from there and see if it helps. It might force flashing the pic's on the hashing boards. will try to do that tomorrow , but there is no intruction inside the .zip will copy the .img to SD with diskimager. Then copy/paste L3+ firmware inside SD ... hope i'm right with steps and miner will autoboot from SD Title: Re: Issue new antminer l3+ Post by: cryptonitro on November 21, 2017, 09:52:18 AM Code: ************ board_new *************** The firmware to copy on SD seem to be designed for S series, i start from it and flash L3+ firmware , flash was ok but still no hashboards and same error in kernel after Code: Nov 21 10:01:33 (none) local0.notice cgminer[5756]: detected at /sys/class/gpio/gpio51/value chain 0 sad :'( Title: Re: Issue new antminer l3+ Post by: blissz on November 22, 2017, 09:14:13 PM Code: ************ board_new *************** The firmware to copy on SD seem to be designed for S series, i start from it and flash L3+ firmware , flash was ok but still no hashboards and same error in kernel after Code: Nov 21 10:01:33 (none) local0.notice cgminer[5756]: detected at /sys/class/gpio/gpio51/value chain 0 sad :'( Hmmmz I'm afraid you need to flash them by hand on the board itself. Let me know if you need any help. Title: Re: Issue new antminer l3+ Post by: cryptonitro on November 24, 2017, 11:33:12 PM i miss the hexa file , i dont know if pic.txt could be the one
Title: Re: Issue new antminer l3+ Post by: Egorrichminer on November 26, 2017, 10:45:14 PM Hi Folks!
Absolutely the same stuff I'm having now with my L3+ too. I had a well working L3+, then by mistake flashed it with D3 firmware (instead of different ASIC device... to fix the "x" issue solved in the 20th of November 2017 formware for D3). After that I immediately re-flashed back to the L3+ firmware but got what i got, Zero chips on each of the four hash-blades... I tried all the stuff including Micri SD image as did here and the same it didn't help. I also need this suggestion on which hex file to take and from where (the path) on the correctly working hash blade from another L3+. So I "ssh" the L3+ and should "scp" the file ?? to the same location on the malfunctioning L3+ (do that for all 4 blades) and then reboot. Cirrect? Which path to the file then guys? Please help. Thanks, Egor Title: Re: Issue new antminer l3+ Post by: cryptonitro on November 28, 2017, 02:31:30 PM Hi Folks! Absolutely the same stuff I'm having now with my L3+ too. I had a well working L3+, then by mistake flashed it with D3 firmware (instead of different ASIC device... to fix the "x" issue solved in the 20th of November 2017 formware for D3). After that I immediately re-flashed back to the L3+ firmware but got what i got, Zero chips on each of the four hash-blades... I tried all the stuff including Micri SD image as did here and the same it didn't help. I also need this suggestion on which hex file to take and from where (the path) on the correctly working hash blade from another L3+. So I "ssh" the L3+ and should "scp" the file ?? to the same location on the malfunctioning L3+ (do that for all 4 blades) and then reboot. Cirrect? Which path to the file then guys? Please help. Thanks, Egor https://img15.hostingpics.net/pics/492654eeprom.jpg need to plug programmation stuff in 6 holes on the right of eeprom texas , and extract hexa file from a working l3+ hashboard, then flash it manually on the fail board $ and share the hexa file for some of us have only one fail l3+ but no other to fix :) Title: Re: Issue new antminer l3+ Post by: gians82 on December 02, 2017, 04:06:02 PM Hello,
I activated today in my new antminer l3 + but I have the exact same problem, it does not recognize any Hashboard. I opened ticket to bitmain. (*the product is new has never been used.) how did you solve this problem? Thanks *I can not open antminer because I lose the guarantee. Title: Re: Issue new antminer l3+ Post by: cryptonitro on December 02, 2017, 05:29:46 PM Hello, bitmain will told to open , and sent them hashboard ... where come from your miner ?I activated today in my new antminer l3 + but I have the exact same problem, it does not recognize any Hashboard. I opened ticket to bitmain. (*the product is new has never been used.) how did you solve this problem? Thanks *I can not open antminer because I lose the guarantee. Title: Re: Issue new antminer l3+ Post by: gians82 on December 03, 2017, 09:09:39 AM Hi,
I bought the miner directly from bitmain in China. But are not the miners tested before shipping? Title: Re: Issue new antminer l3+ Post by: gians82 on December 04, 2017, 02:45:25 PM Hello,
there are no other solutions to solve the problem? Bitmain does not respond to my ticket. Thanks Title: Re: Issue new antminer l3+ Post by: omshree on December 05, 2017, 03:54:47 AM No other solutions apart from sending it back, I am the one who discovered the manual flashing of the PIC controller, and I can confirm it works.
Title: Re: Issue new antminer l3+ Post by: CryptoWatcher420 on December 05, 2017, 07:16:34 AM what rom flashing tool did you use?
Title: Re: Issue new antminer l3+ Post by: gians82 on December 05, 2017, 09:55:05 AM Hi, you tell me how I can do, do you have a guide? Thanks
Bitmain does not respond to my ticket, but I can not understand, the products before being sent are not tested. >:( >:( >:( Title: Re: Issue new antminer l3+ Post by: omshree on December 05, 2017, 09:31:02 PM what rom flashing tool did you use? PICkit3Title: Re: Issue new antminer l3+ Post by: omshree on December 05, 2017, 09:32:04 PM I can fix the boards is you send me, 0.01 btc per board.
Title: Re: Issue new antminer l3+ Post by: hawkfish007 on December 05, 2017, 09:37:29 PM Hi, you tell me how I can do, do you have a guide? Thanks Bitmain does not respond to my ticket, but I can not understand, the products before being sent are not tested. >:( >:( >:( Where are you located? For US residents, you just need to open a repair ticket and send the defective unit to CA repair center under warranty. Bitmain shipped a new D3 from china within 2 days of delivery of my defective unit to CA repair center. Title: Re: Issue new antminer l3+ Post by: omshree on December 05, 2017, 10:04:14 PM Hi, you tell me how I can do, do you have a guide? Thanks Bitmain does not respond to my ticket, but I can not understand, the products before being sent are not tested. >:( >:( >:( Where are you located? For US residents, you just need to open a repair ticket and send the defective unit to CA repair center under warranty. Bitmain shipped a new D3 from china within 2 days of delivery of my defective unit to CA repair center. Title: Re: Issue new antminer l3+ Post by: martin_fryc on December 07, 2017, 07:18:31 PM Hi Folks! Absolutely the same stuff I'm having now with my L3+ too. I had a well working L3+, then by mistake flashed it with D3 firmware (instead of different ASIC device... to fix the "x" issue solved in the 20th of November 2017 formware for D3). After that I immediately re-flashed back to the L3+ firmware but got what i got, Zero chips on each of the four hash-blades... I tried all the stuff including Micri SD image as did here and the same it didn't help. I also need this suggestion on which hex file to take and from where (the path) on the correctly working hash blade from another L3+. So I "ssh" the L3+ and should "scp" the file ?? to the same location on the malfunctioning L3+ (do that for all 4 blades) and then reboot. Cirrect? Which path to the file then guys? Please help. Thanks, Egor https://img15.hostingpics.net/pics/492654eeprom.jpg need to plug programmation stuff in 6 holes on the right of eeprom texas , and extract hexa file from a working l3+ hashboard, then flash it manually on the fail board $ and share the hexa file for some of us have only one fail l3+ but no other to fix :) I had the same issue with my L3+. Mistakenly updated with D3 firmware. I was able to bring it back to life with PICkit 3 and hex file from another L3+. Many thanks guys!!! Title: Re: Issue new antminer l3+ Post by: blissz on December 08, 2017, 10:59:14 AM I am currently compiling a custom L3 firmware version for you guys. It tries to force flash the PIC's on the board. I really have no clue if this works, but I do have hope it can bring your L3's alive.
there you go: WARNING: Don't flash this to anything else as a bricked L3(+) caused by flashing a wrong firmware version, as this might harm a working L3(+). https://mega.nz/#!38BwlbgA!7QCxYomuSGqEb1dSWnxRl27Yo_sGKE7gIwxvtSt9UcA (https://mega.nz/#!38BwlbgA!7QCxYomuSGqEb1dSWnxRl27Yo_sGKE7gIwxvtSt9UcA) let me know if it works / post your kernel log if it doesn't ;) Title: Re: Issue new antminer l3+ Post by: cryptonitro on December 08, 2017, 11:20:44 AM I am currently compiling a custom L3 firmware version for you guys. It tries to force flash the PIC's on the board. I really have no clue if this works, but I do have hope it can bring your L3's alive. there you go: WARNING: Don't flash this to anything else as a bricked L3(+) caused by flashing a wrong firmware version, as this might harm a working L3(+). https://mega.nz/#!38BwlbgA!7QCxYomuSGqEb1dSWnxRl27Yo_sGKE7gIwxvtSt9UcA (https://mega.nz/#!38BwlbgA!7QCxYomuSGqEb1dSWnxRl27Yo_sGKE7gIwxvtSt9UcA) let me know if it works / post your kernel log if it doesn't ;) thanks , just receive your MP , will try it now :) edit : after reboot fan go 100% permanent even if low fan is checked, logs seem to stop after board detect and not flash , overview got : Hardware Version Socket connect failed: Connection refused SD card could be better ? heres the logs Quote [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 64768 pages, LIFO batch:15 [ 0.000000] AM335X ES1.0 (neon ) [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0933000 s9408 r8192 d15168 u32768 [ 0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc:
[ 0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] allocated 524288 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 255MB = 255MB total [ 0.000000] Memory: 238816k/238816k available, 23328k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB) [ 0.000000] .text : 0xc0008000 - 0xc0612cf0 (6188 kB) [ 0.000000] .init : 0xc0613000 - 0xc06554c0 ( 266 kB) [ 0.000000] .data : 0xc0656000 - 0xc06cc020 ( 473 kB) [ 0.000000] .bss : 0xc06cc020 - 0xc0725e3c ( 360 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000357] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968) [ 0.015443] pid_max: default: 32768 minimum: 301 [ 0.015671] Security Framework initialized [ 0.015767] Mount-cache hash table entries: 512 [ 0.024586] Initializing cgroup subsys cpuacct [ 0.024620] Initializing cgroup subsys memory [ 0.024683] Initializing cgroup subsys blkio [ 0.024821] CPU: Testing write buffer coherency: ok [ 0.025391] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.025469] Setting up static identity map for 0x8038c820 - 0x8038c86c [ 0.026793] Brought up 1 CPUs [ 0.026816] SMP: Total of 1 processors activated (545.07 BogoMIPS). [ 0.028114] devtmpfs: initialized [ 0.092508] pinctrl core: initialized pinctrl subsystem [ 0.092721] rstctl core: initialized rstctl subsystem [ 0.093212] regulator-dummy: no parameters [ 0.093779] NET: Registered protocol family 16 [ 0.094482] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.104170] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle [ 0.104356] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.105451] platform 49000000.edma: alias fck already exists [ 0.105484] platform 49000000.edma: alias fck already exists [ 0.105512] platform 49000000.edma: alias fck already exists [ 0.106660] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.106843] OMAP GPIO hardware version 0.1 [ 0.108246] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.109562] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.110884] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.111516] of_get_named_gpio_flags exited with status 52 [ 0.111547] gpio-rctrl rstctl.3: loaded OK [ 0.116646] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.119843] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.122020] cpsw.0: No hwaddr in dt. Using 50:33:8b:04:40:4d from efuse [ 0.122052] cpsw.1: No hwaddr in dt. Using 50:33:8b:04:40:4f from efuse [ 0.137596] bio: create slab <bio-0> at 0 [ 0.149725] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.149965] of_get_named_gpio_flags: can't parse gpios property [ 0.150251] vmmcsd_fixed: 3300 mV [ 0.153368] SCSI subsystem initialized [ 0.153824] usbcore: registered new interface driver usbfs [ 0.153938] usbcore: registered new interface driver hub [ 0.154274] usbcore: registered new device driver usb [ 0.156367] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz [ 0.156400] omap_i2c 4819c000.i2c: unable to select pin group [ 0.156594] media: Linux media interface: v0.10 [ 0.156689] Linux video capture interface: v2.00 [ 0.156807] pps_core: LinuxPPS API ver. 1 registered [ 0.156823] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.157542] Advanced Linux Sound Architecture Driver Initialized. [ 0.158741] Switching to clocksource gp_timer [ 0.176761] NET: Registered protocol family 2 [ 0.177757] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.177846] TCP bind hash table entries: 2048 (order: 3, 40960 bytes) [ 0.177936] TCP: Hash tables configured (established 2048 bind 2048) [ 0.178029] TCP: reno registered [ 0.178056] UDP hash table entries: 256 (order: 1, 12288 bytes) [ 0.178101] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) [ 0.178593] NET: Registered protocol family 1 [ 0.179187] RPC: Registered named UNIX socket transport module. [ 0.179208] RPC: Registered udp transport module. [ 0.179222] RPC: Registered tcp transport module. [ 0.179236] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.179619] Trying to unpack rootfs image as initramfs... [ 1.934124] Freeing initrd memory: 12100K [ 1.934850] CPU PMU: probing PMU on CPU 0 [ 1.934882] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 1.935414] omap2_mbox_probe: platform not supported [ 1.939313] VFS: Disk quotas dquot_6.5.2 [ 1.939550] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.940956] NFS: Registering the id_resolver key type [ 1.941050] Key type id_resolver registered [ 1.941068] Key type id_legacy registered [ 1.941133] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.941592] msgmni has been set to 490 [ 1.944483] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.944510] io scheduler noop registered [ 1.944526] io scheduler deadline registered [ 1.944584] io scheduler cfq registered (default) [ 1.948656] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.951092] omap_uart 44e09000.serial: did not get pins for uart0 error: -19 [ 1.951380] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0 [ 2.612216] console [ttyO0] enabled [ 2.616753] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1 [ 2.625415] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2 [ 2.634099] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4 [ 2.642707] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5 [ 2.651734] [drm] Initialized drm 1.1.0 20060810 [ 2.670416] brd: module loaded [ 2.680714] loop: module loaded [ 2.684931] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node [ 2.694913] nand_get_flash_type: 2c,da against 2c,da [ 2.700437] ONFI param page 0 valid [ 2.704109] ONFI flash detected [ 2.707428] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64 [ 2.719341] omap2-nand: detected x8 NAND flash [ 2.724007] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme [ 2.729589] omap2-nand: using custom ecc layout [ 2.734428] 10 ofpart partitions found on MTD device omap2-nand.0 [ 2.740820] Creating 10 MTD partitions on "omap2-nand.0": [ 2.746497] 0x000000000000-0x000000020000 : "spl" [ 2.753311] 0x000000020000-0x000000040000 : "spl_backup1" [ 2.760751] 0x000000040000-0x000000060000 : "spl_backup2" [ 2.768126] 0x000000060000-0x000000080000 : "spl_backup3" [ 2.775541] 0x000000080000-0x000000240000 : "u-boot" [ 2.783775] 0x000000240000-0x000000260000 : "bootenv" [ 2.790717] 0x000000260000-0x000000280000 : "fdt" [ 2.797295] 0x000000280000-0x000000780000 : "kernel" [ 2.808326] 0x000000800000-0x000001c00000 : "root" [ 2.831826] 0x000001c00000-0x000003000000 : "config" [ 2.855616] OneNAND driver initializing [ 2.861360] usbcore: registered new interface driver asix [ 2.867176] usbcore: registered new interface driver cdc_ether [ 2.873423] usbcore: registered new interface driver smsc95xx [ 2.879572] usbcore: registered new interface driver net1080 [ 2.885594] usbcore: registered new interface driver cdc_subset [ 2.891888] usbcore: registered new interface driver zaurus [ 2.897895] usbcore: registered new interface driver cdc_ncm [ 2.904623] usbcore: registered new interface driver cdc_acm [ 2.910580] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 2.918961] Initializing USB Mass Storage driver... [ 2.924203] usbcore: registered new interface driver usb-storage [ 2.930502] USB Mass Storage support registered. [ 2.935542] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 2.942294] musb-hdrc musb-hdrc.0.auto: pdev->id = 0 [ 2.947533] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.956304] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.956325] musb-hdrc: MHDRC RTL version 2.0 [ 2.956340] musb-hdrc: setup fifo_mode 4 [ 2.956368] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.956515] musb-hdrc musb-hdrc.0.auto: *** mode=3 [ 2.961574] musb-hdrc musb-hdrc.0.auto: *** power=250 [ 2.967638] musb-hdrc musb-hdrc.1.auto: pdev->id = 1 [ 2.972880] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.981652] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.981672] musb-hdrc: MHDRC RTL version 2.0 [ 2.981685] musb-hdrc: setup fifo_mode 4 [ 2.981708] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.981849] musb-hdrc musb-hdrc.1.auto: *** mode=1 [ 2.986893] musb-hdrc musb-hdrc.1.auto: *** power=250 [ 2.992201] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 2.998578] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 3.007051] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup [ 3.007160] usb usb1: default language 0x0409 [ 3.007217] usb usb1: udev 1, busnum 1, minor = 0 [ 3.007241] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.014386] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.021961] usb usb1: Product: MUSB HDRC host driver [ 3.027176] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd [ 3.032844] usb usb1: SerialNumber: musb-hdrc.1.auto [ 3.038832] usb usb1: usb_probe_device [ 3.038862] usb usb1: configuration #1 chosen from 1 choice [ 3.038928] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 3.039127] hub 1-0:1.0: usb_probe_interface [ 3.039150] hub 1-0:1.0: usb_probe_interface - got id [ 3.039178] hub 1-0:1.0: USB hub found [ 3.043182] hub 1-0:1.0: 1 port detected [ 3.047321] hub 1-0:1.0: standalone hub [ 3.047341] hub 1-0:1.0: individual port power switching [ 3.047359] hub 1-0:1.0: no over-current protection [ 3.047377] hub 1-0:1.0: Single TT [ 3.047397] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 3.047417] hub 1-0:1.0: power on to power good time: 10ms [ 3.047473] hub 1-0:1.0: local power source is good [ 3.047622] hub 1-0:1.0: enabling power on all ports [ 3.048673] mousedev: PS/2 mouse device common for all mice [ 3.056644] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 3.064147] 44e3e000.rtc: already running [ 3.068646] i2c /dev entries driver [ 3.073705] pps_ldisc: PPS line discipline registered [ 3.079187] Driver for 1-wire Dallas network protocol. [ 3.086442] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 3.094018] cpuidle: using governor ladder [ 3.098347] cpuidle: using governor menu [ 3.102920] of_get_named_gpio_flags exited with status 6 [ 3.102940] of_get_named_gpio_flags: can't parse gpios property [ 3.102956] of_get_named_gpio_flags: can't parse gpios property [ 3.102992] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed [ 3.110213] omap_hsmmc mmc.4: Failed to get rstctl; not using any [ 3.117021] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 3.124244] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 3.131599] mmc.4 supply vmmc_aux not found, using dummy regulator [ 3.138534] omap_hsmmc mmc.4: pins are not configured from the driver [ 3.149196] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 3.173114] of_get_named_gpio_flags exited with status -517 [ 3.173181] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.180962] ledtrig-cpu: registered to indicate activity on CPUs [ 3.187742] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36 [ 3.194940] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 3.203103] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 3.209406] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 [ 3.216580] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 [ 3.228825] usbcore: registered new interface driver usbhid [ 3.234740] usbhid: USB HID core driver [ 3.241655] TCP: cubic registered [ 3.245183] Initializing XFRM netlink socket [ 3.249762] NET: Registered protocol family 17 [ 3.254625] NET: Registered protocol family 15 [ 3.259472] Key type dns_resolver registered [ 3.264116] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 3.272228] ThumbEE CPU extension supported. [ 3.276742] Registering SWP/SWPB emulation handler [ 3.282754] registered taskstats version 1 [ 3.289376] of_get_named_gpio_flags exited with status -517 [ 3.289452] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.346395] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 3.352844] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 3.367334] libphy: 4a101000.mdio: probed [ 3.371654] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 3.381888] Detected MACID = 50:33:8b:04:40:4d [ 3.386572] cpsw 4a100000.ethernet: NAPI disabled [ 3.391966] of_get_named_gpio_flags exited with status -517 [ 3.392032] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.400775] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.410061] cpu0 supply cpu0 not found, using dummy regulator [ 3.416545] cpufreq_cpu0: failed to scale voltage up: -22 [ 3.422366] cpufreq_cpu0: failed to scale voltage up: -22 [ 3.435148] ALSA device list: [ 3.438381] No soundcards found. [ 3.442923] Freeing init memory: 264K [ 3.446979] Failed to execute /init [ 4.465849] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 5.777413] net eth0: initializing cpsw version 1.12 (0) [ 5.786472] net eth0: phy found : id is : 0x7c0f1 [ 5.791912] libphy: PHY 4a101000.mdio:01 not found [ 5.797108] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 8.864483] libphy: 4a101000.mdio:00 - Link is Up - 100/Full Dec 8 11:29:30 (none) local0.err cgminer: Miner compile time: Fri Aug 25 17:28:57 CST 2017 type: Antminer L3+ Dec 8 11:29:30 (none) local0.warn cgminer: Started cgminer 4.9.0 Dec 8 11:29:30 (none) local0.notice cgminer[374]: detected at /sys/class/gpio/gpio51/value chain 0 Dec 8 11:29:30 (none) local0.notice cgminer[374]: detected at /sys/class/gpio/gpio48/value chain 1 Dec 8 11:29:30 (none) local0.notice cgminer[374]: detected at /sys/class/gpio/gpio47/value chain 2 Dec 8 11:29:30 (none) local0.notice cgminer[374]: detected at /sys/class/gpio/gpio44/value chain 3 Dec 8 11:29:30 (none) local0.notice cgminer[374]: detect total chain num 4 Dec 8 11:29:30 (none) local0.notice cgminer[374]: i2c init ok Title: Re: Issue new antminer l3+ Post by: blissz on December 08, 2017, 11:44:54 AM I am currently compiling a custom L3 firmware version for you guys. It tries to force flash the PIC's on the board. I really have no clue if this works, but I do have hope it can bring your L3's alive. there you go: WARNING: Don't flash this to anything else as a bricked L3(+) caused by flashing a wrong firmware version, as this might harm a working L3(+). https://mega.nz/#!38BwlbgA!7QCxYomuSGqEb1dSWnxRl27Yo_sGKE7gIwxvtSt9UcA (https://mega.nz/#!38BwlbgA!7QCxYomuSGqEb1dSWnxRl27Yo_sGKE7gIwxvtSt9UcA) let me know if it works / post your kernel log if it doesn't ;) thanks , just receive your MP , will try it now :) edit : after reboot fan go 100% permanent even if low fan is checked, logs seem to stop after board detect and not flash , overview got : Hardware Version Socket connect failed: Connection refused SD card could be better ? heres the logs Quote [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 64768 pages, LIFO batch:15 [ 0.000000] AM335X ES1.0 (neon ) [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0933000 s9408 r8192 d15168 u32768 [ 0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc:
[ 0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] allocated 524288 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 255MB = 255MB total [ 0.000000] Memory: 238816k/238816k available, 23328k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB) [ 0.000000] .text : 0xc0008000 - 0xc0612cf0 (6188 kB) [ 0.000000] .init : 0xc0613000 - 0xc06554c0 ( 266 kB) [ 0.000000] .data : 0xc0656000 - 0xc06cc020 ( 473 kB) [ 0.000000] .bss : 0xc06cc020 - 0xc0725e3c ( 360 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000357] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968) [ 0.015443] pid_max: default: 32768 minimum: 301 [ 0.015671] Security Framework initialized [ 0.015767] Mount-cache hash table entries: 512 [ 0.024586] Initializing cgroup subsys cpuacct [ 0.024620] Initializing cgroup subsys memory [ 0.024683] Initializing cgroup subsys blkio [ 0.024821] CPU: Testing write buffer coherency: ok [ 0.025391] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.025469] Setting up static identity map for 0x8038c820 - 0x8038c86c [ 0.026793] Brought up 1 CPUs [ 0.026816] SMP: Total of 1 processors activated (545.07 BogoMIPS). [ 0.028114] devtmpfs: initialized [ 0.092508] pinctrl core: initialized pinctrl subsystem [ 0.092721] rstctl core: initialized rstctl subsystem [ 0.093212] regulator-dummy: no parameters [ 0.093779] NET: Registered protocol family 16 [ 0.094482] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.104170] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle [ 0.104356] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.105451] platform 49000000.edma: alias fck already exists [ 0.105484] platform 49000000.edma: alias fck already exists [ 0.105512] platform 49000000.edma: alias fck already exists [ 0.106660] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.106843] OMAP GPIO hardware version 0.1 [ 0.108246] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.109562] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.110884] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.111516] of_get_named_gpio_flags exited with status 52 [ 0.111547] gpio-rctrl rstctl.3: loaded OK [ 0.116646] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.119843] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.122020] cpsw.0: No hwaddr in dt. Using 50:33:8b:04:40:4d from efuse [ 0.122052] cpsw.1: No hwaddr in dt. Using 50:33:8b:04:40:4f from efuse [ 0.137596] bio: create slab <bio-0> at 0 [ 0.149725] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.149965] of_get_named_gpio_flags: can't parse gpios property [ 0.150251] vmmcsd_fixed: 3300 mV [ 0.153368] SCSI subsystem initialized [ 0.153824] usbcore: registered new interface driver usbfs [ 0.153938] usbcore: registered new interface driver hub [ 0.154274] usbcore: registered new device driver usb [ 0.156367] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz [ 0.156400] omap_i2c 4819c000.i2c: unable to select pin group [ 0.156594] media: Linux media interface: v0.10 [ 0.156689] Linux video capture interface: v2.00 [ 0.156807] pps_core: LinuxPPS API ver. 1 registered [ 0.156823] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.157542] Advanced Linux Sound Architecture Driver Initialized. [ 0.158741] Switching to clocksource gp_timer [ 0.176761] NET: Registered protocol family 2 [ 0.177757] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.177846] TCP bind hash table entries: 2048 (order: 3, 40960 bytes) [ 0.177936] TCP: Hash tables configured (established 2048 bind 2048) [ 0.178029] TCP: reno registered [ 0.178056] UDP hash table entries: 256 (order: 1, 12288 bytes) [ 0.178101] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) [ 0.178593] NET: Registered protocol family 1 [ 0.179187] RPC: Registered named UNIX socket transport module. [ 0.179208] RPC: Registered udp transport module. [ 0.179222] RPC: Registered tcp transport module. [ 0.179236] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.179619] Trying to unpack rootfs image as initramfs... [ 1.934124] Freeing initrd memory: 12100K [ 1.934850] CPU PMU: probing PMU on CPU 0 [ 1.934882] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 1.935414] omap2_mbox_probe: platform not supported [ 1.939313] VFS: Disk quotas dquot_6.5.2 [ 1.939550] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.940956] NFS: Registering the id_resolver key type [ 1.941050] Key type id_resolver registered [ 1.941068] Key type id_legacy registered [ 1.941133] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.941592] msgmni has been set to 490 [ 1.944483] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.944510] io scheduler noop registered [ 1.944526] io scheduler deadline registered [ 1.944584] io scheduler cfq registered (default) [ 1.948656] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.951092] omap_uart 44e09000.serial: did not get pins for uart0 error: -19 [ 1.951380] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0 [ 2.612216] console [ttyO0] enabled [ 2.616753] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1 [ 2.625415] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2 [ 2.634099] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4 [ 2.642707] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5 [ 2.651734] [drm] Initialized drm 1.1.0 20060810 [ 2.670416] brd: module loaded [ 2.680714] loop: module loaded [ 2.684931] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node [ 2.694913] nand_get_flash_type: 2c,da against 2c,da [ 2.700437] ONFI param page 0 valid [ 2.704109] ONFI flash detected [ 2.707428] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64 [ 2.719341] omap2-nand: detected x8 NAND flash [ 2.724007] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme [ 2.729589] omap2-nand: using custom ecc layout [ 2.734428] 10 ofpart partitions found on MTD device omap2-nand.0 [ 2.740820] Creating 10 MTD partitions on "omap2-nand.0": [ 2.746497] 0x000000000000-0x000000020000 : "spl" [ 2.753311] 0x000000020000-0x000000040000 : "spl_backup1" [ 2.760751] 0x000000040000-0x000000060000 : "spl_backup2" [ 2.768126] 0x000000060000-0x000000080000 : "spl_backup3" [ 2.775541] 0x000000080000-0x000000240000 : "u-boot" [ 2.783775] 0x000000240000-0x000000260000 : "bootenv" [ 2.790717] 0x000000260000-0x000000280000 : "fdt" [ 2.797295] 0x000000280000-0x000000780000 : "kernel" [ 2.808326] 0x000000800000-0x000001c00000 : "root" [ 2.831826] 0x000001c00000-0x000003000000 : "config" [ 2.855616] OneNAND driver initializing [ 2.861360] usbcore: registered new interface driver asix [ 2.867176] usbcore: registered new interface driver cdc_ether [ 2.873423] usbcore: registered new interface driver smsc95xx [ 2.879572] usbcore: registered new interface driver net1080 [ 2.885594] usbcore: registered new interface driver cdc_subset [ 2.891888] usbcore: registered new interface driver zaurus [ 2.897895] usbcore: registered new interface driver cdc_ncm [ 2.904623] usbcore: registered new interface driver cdc_acm [ 2.910580] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 2.918961] Initializing USB Mass Storage driver... [ 2.924203] usbcore: registered new interface driver usb-storage [ 2.930502] USB Mass Storage support registered. [ 2.935542] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 2.942294] musb-hdrc musb-hdrc.0.auto: pdev->id = 0 [ 2.947533] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.956304] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.956325] musb-hdrc: MHDRC RTL version 2.0 [ 2.956340] musb-hdrc: setup fifo_mode 4 [ 2.956368] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.956515] musb-hdrc musb-hdrc.0.auto: *** mode=3 [ 2.961574] musb-hdrc musb-hdrc.0.auto: *** power=250 [ 2.967638] musb-hdrc musb-hdrc.1.auto: pdev->id = 1 [ 2.972880] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.981652] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.981672] musb-hdrc: MHDRC RTL version 2.0 [ 2.981685] musb-hdrc: setup fifo_mode 4 [ 2.981708] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.981849] musb-hdrc musb-hdrc.1.auto: *** mode=1 [ 2.986893] musb-hdrc musb-hdrc.1.auto: *** power=250 [ 2.992201] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 2.998578] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 3.007051] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup [ 3.007160] usb usb1: default language 0x0409 [ 3.007217] usb usb1: udev 1, busnum 1, minor = 0 [ 3.007241] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.014386] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.021961] usb usb1: Product: MUSB HDRC host driver [ 3.027176] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd [ 3.032844] usb usb1: SerialNumber: musb-hdrc.1.auto [ 3.038832] usb usb1: usb_probe_device [ 3.038862] usb usb1: configuration #1 chosen from 1 choice [ 3.038928] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 3.039127] hub 1-0:1.0: usb_probe_interface [ 3.039150] hub 1-0:1.0: usb_probe_interface - got id [ 3.039178] hub 1-0:1.0: USB hub found [ 3.043182] hub 1-0:1.0: 1 port detected [ 3.047321] hub 1-0:1.0: standalone hub [ 3.047341] hub 1-0:1.0: individual port power switching [ 3.047359] hub 1-0:1.0: no over-current protection [ 3.047377] hub 1-0:1.0: Single TT [ 3.047397] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 3.047417] hub 1-0:1.0: power on to power good time: 10ms [ 3.047473] hub 1-0:1.0: local power source is good [ 3.047622] hub 1-0:1.0: enabling power on all ports [ 3.048673] mousedev: PS/2 mouse device common for all mice [ 3.056644] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 3.064147] 44e3e000.rtc: already running [ 3.068646] i2c /dev entries driver [ 3.073705] pps_ldisc: PPS line discipline registered [ 3.079187] Driver for 1-wire Dallas network protocol. [ 3.086442] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 3.094018] cpuidle: using governor ladder [ 3.098347] cpuidle: using governor menu [ 3.102920] of_get_named_gpio_flags exited with status 6 [ 3.102940] of_get_named_gpio_flags: can't parse gpios property [ 3.102956] of_get_named_gpio_flags: can't parse gpios property [ 3.102992] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed [ 3.110213] omap_hsmmc mmc.4: Failed to get rstctl; not using any [ 3.117021] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 3.124244] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 3.131599] mmc.4 supply vmmc_aux not found, using dummy regulator [ 3.138534] omap_hsmmc mmc.4: pins are not configured from the driver [ 3.149196] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 3.173114] of_get_named_gpio_flags exited with status -517 [ 3.173181] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.180962] ledtrig-cpu: registered to indicate activity on CPUs [ 3.187742] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36 [ 3.194940] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 3.203103] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 3.209406] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 [ 3.216580] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 [ 3.228825] usbcore: registered new interface driver usbhid [ 3.234740] usbhid: USB HID core driver [ 3.241655] TCP: cubic registered [ 3.245183] Initializing XFRM netlink socket [ 3.249762] NET: Registered protocol family 17 [ 3.254625] NET: Registered protocol family 15 [ 3.259472] Key type dns_resolver registered [ 3.264116] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 3.272228] ThumbEE CPU extension supported. [ 3.276742] Registering SWP/SWPB emulation handler [ 3.282754] registered taskstats version 1 [ 3.289376] of_get_named_gpio_flags exited with status -517 [ 3.289452] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.346395] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 3.352844] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 3.367334] libphy: 4a101000.mdio: probed [ 3.371654] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 3.381888] Detected MACID = 50:33:8b:04:40:4d [ 3.386572] cpsw 4a100000.ethernet: NAPI disabled [ 3.391966] of_get_named_gpio_flags exited with status -517 [ 3.392032] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.400775] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.410061] cpu0 supply cpu0 not found, using dummy regulator [ 3.416545] cpufreq_cpu0: failed to scale voltage up: -22 [ 3.422366] cpufreq_cpu0: failed to scale voltage up: -22 [ 3.435148] ALSA device list: [ 3.438381] No soundcards found. [ 3.442923] Freeing init memory: 264K [ 3.446979] Failed to execute /init [ 4.465849] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 5.777413] net eth0: initializing cpsw version 1.12 (0) [ 5.786472] net eth0: phy found : id is : 0x7c0f1 [ 5.791912] libphy: PHY 4a101000.mdio:01 not found [ 5.797108] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 8.864483] libphy: 4a101000.mdio:00 - Link is Up - 100/Full Dec 8 11:29:30 (none) local0.err cgminer: Miner compile time: Fri Aug 25 17:28:57 CST 2017 type: Antminer L3+ Dec 8 11:29:30 (none) local0.warn cgminer: Started cgminer 4.9.0 Dec 8 11:29:30 (none) local0.notice cgminer[374]: detected at /sys/class/gpio/gpio51/value chain 0 Dec 8 11:29:30 (none) local0.notice cgminer[374]: detected at /sys/class/gpio/gpio48/value chain 1 Dec 8 11:29:30 (none) local0.notice cgminer[374]: detected at /sys/class/gpio/gpio47/value chain 2 Dec 8 11:29:30 (none) local0.notice cgminer[374]: detected at /sys/class/gpio/gpio44/value chain 3 Dec 8 11:29:30 (none) local0.notice cgminer[374]: detect total chain num 4 Dec 8 11:29:30 (none) local0.notice cgminer[374]: i2c init ok Isn't there more after this last kernel log line? Title: Re: Issue new antminer l3+ Post by: cryptonitro on December 08, 2017, 12:06:19 PM unfortunatly no , it seem to stop here , and seem in default cause fan are running 100% , but no redlight on front
Title: Re: Issue new antminer l3+ Post by: blissz on December 08, 2017, 12:41:10 PM and try again with this one, I don't expect much of it yet, but just the kernel logging is interesting for me what to try next:
WARNING: Don't flash this to anything else as a bricked L3(+) caused by flashing a wrong firmware version, as this might harm a working L3(+). https://mega.nz/#!utgGWSbT!hAXEVCgUodhtdKQm1Zfs7rFyDtPEwS85MC-LbJqHhHc (https://mega.nz/#!utgGWSbT!hAXEVCgUodhtdKQm1Zfs7rFyDtPEwS85MC-LbJqHhHc) Title: Re: Issue new antminer l3+ Post by: playboy333 on December 08, 2017, 01:37:16 PM and try again with this one, I don't expect much of it yet, but just the kernel logging is interesting for me what to try next: WARNING: Don't flash this to anything else as a bricked L3(+) caused by flashing a wrong firmware version, as this might harm a working L3(+). https://mega.nz/#!utgGWSbT!hAXEVCgUodhtdKQm1Zfs7rFyDtPEwS85MC-LbJqHhHc (https://mega.nz/#!utgGWSbT!hAXEVCgUodhtdKQm1Zfs7rFyDtPEwS85MC-LbJqHhHc) [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 64768 pages, LIFO batch:15 [ 0.000000] AM335X ES1.0 (neon ) [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0933000 s9408 r8192 d15168 u32768 [ 0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc:
[ 0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] allocated 524288 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 255MB = 255MB total [ 0.000000] Memory: 238816k/238816k available, 23328k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB) [ 0.000000] .text : 0xc0008000 - 0xc0612cf0 (6188 kB) [ 0.000000] .init : 0xc0613000 - 0xc06554c0 ( 266 kB) [ 0.000000] .data : 0xc0656000 - 0xc06cc020 ( 473 kB) [ 0.000000] .bss : 0xc06cc020 - 0xc0725e3c ( 360 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000356] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968) [ 0.015439] pid_max: default: 32768 minimum: 301 [ 0.015672] Security Framework initialized [ 0.015768] Mount-cache hash table entries: 512 [ 0.024603] Initializing cgroup subsys cpuacct [ 0.024636] Initializing cgroup subsys memory [ 0.024699] Initializing cgroup subsys blkio [ 0.024833] CPU: Testing write buffer coherency: ok [ 0.025403] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.025480] Setting up static identity map for 0x8038c820 - 0x8038c86c [ 0.026811] Brought up 1 CPUs [ 0.026834] SMP: Total of 1 processors activated (545.07 BogoMIPS). [ 0.028123] devtmpfs: initialized [ 0.092517] pinctrl core: initialized pinctrl subsystem [ 0.092733] rstctl core: initialized rstctl subsystem [ 0.093225] regulator-dummy: no parameters [ 0.093796] NET: Registered protocol family 16 [ 0.094501] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.104171] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle [ 0.104353] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.105442] platform 49000000.edma: alias fck already exists [ 0.105476] platform 49000000.edma: alias fck already exists [ 0.105505] platform 49000000.edma: alias fck already exists [ 0.106656] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.106838] OMAP GPIO hardware version 0.1 [ 0.108250] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.109571] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.110884] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.111517] of_get_named_gpio_flags exited with status 52 [ 0.111547] gpio-rctrl rstctl.3: loaded OK [ 0.116647] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.119866] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.122059] cpsw.0: No hwaddr in dt. Using 90:70:65:3a:fc:95 from efuse [ 0.122092] cpsw.1: No hwaddr in dt. Using 90:70:65:3a:fc:97 from efuse [ 0.137670] bio: create slab <bio-0> at 0 [ 0.149800] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.150043] of_get_named_gpio_flags: can't parse gpios property [ 0.150338] vmmcsd_fixed: 3300 mV [ 0.153450] SCSI subsystem initialized [ 0.153905] usbcore: registered new interface driver usbfs [ 0.154019] usbcore: registered new interface driver hub [ 0.154345] usbcore: registered new device driver usb [ 0.156452] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz [ 0.156485] omap_i2c 4819c000.i2c: unable to select pin group [ 0.156680] media: Linux media interface: v0.10 [ 0.156775] Linux video capture interface: v2.00 [ 0.156893] pps_core: LinuxPPS API ver. 1 registered [ 0.156910] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.157622] Advanced Linux Sound Architecture Driver Initialized. [ 0.158808] Switching to clocksource gp_timer [ 0.176799] NET: Registered protocol family 2 [ 0.177788] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.177877] TCP bind hash table entries: 2048 (order: 3, 40960 bytes) [ 0.177967] TCP: Hash tables configured (established 2048 bind 2048) [ 0.178058] TCP: reno registered [ 0.178085] UDP hash table entries: 256 (order: 1, 12288 bytes) [ 0.178132] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) [ 0.178619] NET: Registered protocol family 1 [ 0.179210] RPC: Registered named UNIX socket transport module. [ 0.179232] RPC: Registered udp transport module. [ 0.179246] RPC: Registered tcp transport module. [ 0.179260] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.179646] Trying to unpack rootfs image as initramfs... [ 1.934714] Freeing initrd memory: 12100K [ 1.935368] CPU PMU: probing PMU on CPU 0 [ 1.935401] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 1.935947] omap2_mbox_probe: platform not supported [ 1.939825] VFS: Disk quotas dquot_6.5.2 [ 1.940062] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.941491] NFS: Registering the id_resolver key type [ 1.941620] Key type id_resolver registered [ 1.941637] Key type id_legacy registered [ 1.941704] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.942252] msgmni has been set to 490 [ 1.945042] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.945067] io scheduler noop registered [ 1.945083] io scheduler deadline registered [ 1.945132] io scheduler cfq registered (default) [ 1.949151] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.951613] omap_uart 44e09000.serial: did not get pins for uart0 error: -19 [ 1.951988] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0 [ 2.612761] console [ttyO0] enabled [ 2.617317] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1 [ 2.626060] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2 [ 2.634696] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4 [ 2.643349] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5 [ 2.652323] [drm] Initialized drm 1.1.0 20060810 [ 2.670986] brd: module loaded [ 2.681263] loop: module loaded [ 2.685444] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node [ 2.695406] nand_get_flash_type: 2c,da against 2c,da [ 2.700927] ONFI param page 0 valid [ 2.704599] ONFI flash detected [ 2.707918] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64 [ 2.719827] omap2-nand: detected x8 NAND flash [ 2.724490] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme [ 2.730072] omap2-nand: using custom ecc layout [ 2.734905] 10 ofpart partitions found on MTD device omap2-nand.0 [ 2.741295] Creating 10 MTD partitions on "omap2-nand.0": [ 2.746965] 0x000000000000-0x000000020000 : "spl" [ 2.753770] 0x000000020000-0x000000040000 : "spl_backup1" [ 2.761210] 0x000000040000-0x000000060000 : "spl_backup2" [ 2.768633] 0x000000060000-0x000000080000 : "spl_backup3" [ 2.775984] 0x000000080000-0x000000240000 : "u-boot" [ 2.784243] 0x000000240000-0x000000260000 : "bootenv" [ 2.791160] 0x000000260000-0x000000280000 : "fdt" [ 2.797790] 0x000000280000-0x000000780000 : "kernel" [ 2.808794] 0x000000800000-0x000001c00000 : "root" [ 2.832265] 0x000001c00000-0x000003000000 : "config" [ 2.856025] OneNAND driver initializing [ 2.861718] usbcore: registered new interface driver asix [ 2.867537] usbcore: registered new interface driver cdc_ether [ 2.873808] usbcore: registered new interface driver smsc95xx [ 2.879915] usbcore: registered new interface driver net1080 [ 2.885933] usbcore: registered new interface driver cdc_subset [ 2.892220] usbcore: registered new interface driver zaurus [ 2.898221] usbcore: registered new interface driver cdc_ncm [ 2.904944] usbcore: registered new interface driver cdc_acm [ 2.910902] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 2.919279] Initializing USB Mass Storage driver... [ 2.924541] usbcore: registered new interface driver usb-storage [ 2.930839] USB Mass Storage support registered. [ 2.935874] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 2.942580] musb-hdrc musb-hdrc.0.auto: pdev->id = 0 [ 2.947824] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.956589] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.956611] musb-hdrc: MHDRC RTL version 2.0 [ 2.956626] musb-hdrc: setup fifo_mode 4 [ 2.956655] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.956799] musb-hdrc musb-hdrc.0.auto: *** mode=3 [ 2.961841] musb-hdrc musb-hdrc.0.auto: *** power=250 [ 2.967907] musb-hdrc musb-hdrc.1.auto: pdev->id = 1 [ 2.973153] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.981917] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.981937] musb-hdrc: MHDRC RTL version 2.0 [ 2.981951] musb-hdrc: setup fifo_mode 4 [ 2.981973] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.982111] musb-hdrc musb-hdrc.1.auto: *** mode=1 [ 2.987153] musb-hdrc musb-hdrc.1.auto: *** power=250 [ 2.992459] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 2.998863] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 3.007331] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup [ 3.007439] usb usb1: default language 0x0409 [ 3.007497] usb usb1: udev 1, busnum 1, minor = 0 [ 3.007521] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.014660] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.022231] usb usb1: Product: MUSB HDRC host driver [ 3.027445] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd [ 3.033111] usb usb1: SerialNumber: musb-hdrc.1.auto [ 3.039093] usb usb1: usb_probe_device [ 3.039122] usb usb1: configuration #1 chosen from 1 choice [ 3.039187] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 3.039388] hub 1-0:1.0: usb_probe_interface [ 3.039411] hub 1-0:1.0: usb_probe_interface - got id [ 3.039438] hub 1-0:1.0: USB hub found [ 3.043489] hub 1-0:1.0: 1 port detected [ 3.047658] hub 1-0:1.0: standalone hub [ 3.047679] hub 1-0:1.0: individual port power switching [ 3.047697] hub 1-0:1.0: no over-current protection [ 3.047715] hub 1-0:1.0: Single TT [ 3.047736] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 3.047756] hub 1-0:1.0: power on to power good time: 10ms [ 3.047811] hub 1-0:1.0: local power source is good [ 3.047927] hub 1-0:1.0: enabling power on all ports [ 3.048972] mousedev: PS/2 mouse device common for all mice [ 3.056986] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 3.064495] 44e3e000.rtc: already running [ 3.068985] i2c /dev entries driver [ 3.074011] pps_ldisc: PPS line discipline registered [ 3.079490] Driver for 1-wire Dallas network protocol. [ 3.086804] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 3.094360] cpuidle: using governor ladder [ 3.098685] cpuidle: using governor menu [ 3.103259] of_get_named_gpio_flags exited with status 6 [ 3.103278] of_get_named_gpio_flags: can't parse gpios property [ 3.103294] of_get_named_gpio_flags: can't parse gpios property [ 3.103331] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed [ 3.110551] omap_hsmmc mmc.4: Failed to get rstctl; not using any [ 3.117359] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 3.124576] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 3.131889] mmc.4 supply vmmc_aux not found, using dummy regulator [ 3.138830] omap_hsmmc mmc.4: pins are not configured from the driver [ 3.149287] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 3.173301] of_get_named_gpio_flags exited with status -517 [ 3.173367] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.181016] ledtrig-cpu: registered to indicate activity on CPUs [ 3.187795] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36 [ 3.194984] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 3.203155] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 3.209446] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 [ 3.216628] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 [ 3.228843] usbcore: registered new interface driver usbhid [ 3.234766] usbhid: USB HID core driver [ 3.241683] TCP: cubic registered [ 3.245208] Initializing XFRM netlink socket [ 3.249783] NET: Registered protocol family 17 [ 3.254678] NET: Registered protocol family 15 [ 3.259540] Key type dns_resolver registered [ 3.264171] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 3.272251] ThumbEE CPU extension supported. [ 3.276760] Registering SWP/SWPB emulation handler [ 3.282790] registered taskstats version 1 [ 3.289417] of_get_named_gpio_flags exited with status -517 [ 3.289490] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.346464] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 3.352916] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 3.367375] libphy: 4a101000.mdio: probed [ 3.371690] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 3.381931] Detected MACID = 90:70:65:3a:fc:95 [ 3.386614] cpsw 4a100000.ethernet: NAPI disabled [ 3.392005] of_get_named_gpio_flags exited with status -517 [ 3.392074] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.400808] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.410090] cpu0 supply cpu0 not found, using dummy regulator [ 3.416588] cpufreq_cpu0: failed to scale voltage up: -22 [ 3.422409] cpufreq_cpu0: failed to scale voltage up: -22 [ 3.435171] ALSA device list: [ 3.438402] No soundcards found. [ 3.442970] Freeing init memory: 264K [ 3.447023] Failed to execute /init [ 4.427328] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 5.764689] net eth0: initializing cpsw version 1.12 (0) [ 5.773572] net eth0: phy found : id is : 0x7c0f1 [ 5.779004] libphy: PHY 4a101000.mdio:01 not found [ 5.784200] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 9.919210] libphy: 4a101000.mdio:00 - Link is Up - 100/Full Dec 8 13:34:26 (none) local0.err cgminer: Miner compile time: Fri Aug 25 17:28:57 CST 2017 type: Antminer L3+ Dec 8 13:34:26 (none) local0.warn cgminer: Started cgminer 4.9.0 Dec 8 13:34:26 (none) local0.notice cgminer[382]: detected at /sys/class/gpio/gpio51/value chain 0 Dec 8 13:34:26 (none) local0.notice cgminer[382]: detected at /sys/class/gpio/gpio48/value chain 1 Dec 8 13:34:26 (none) local0.notice cgminer[382]: detected at /sys/class/gpio/gpio47/value chain 2 Dec 8 13:34:26 (none) local0.notice cgminer[382]: detected at /sys/class/gpio/gpio44/value chain 3 Dec 8 13:34:26 (none) local0.notice cgminer[382]: detect total chain num 4 Dec 8 13:34:26 (none) local0.notice cgminer[382]: i2c init ok Dec 8 13:34:29 (none) local0.notice cgminer[382]: Chain 0 PIC Version 0xcc Title: Re: Issue new antminer l3+ Post by: blissz on December 08, 2017, 02:03:27 PM Interesting. You only have one chain connected now or...?
Title: Re: Issue new antminer l3+ Post by: playboy333 on December 08, 2017, 02:12:09 PM Interesting. You only have one chain connected now or...? All 4 are connected. The same thing is happening fans are at 100% speed and no hashboards detected.Title: Re: Issue new antminer l3+ Post by: blissz on December 08, 2017, 02:18:38 PM Interesting. You only have one chain connected now or...? All 4 are connected. The same thing is happening fans are at 100% speed and no hashboards detected.Can you try to connect just the first chain and see what happens then Title: Re: Issue new antminer l3+ Post by: playboy333 on December 08, 2017, 02:45:04 PM Interesting. You only have one chain connected now or...? All 4 are connected. The same thing is happening fans are at 100% speed and no hashboards detected.Can you try to connect just the first chain and see what happens then [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 64768 pages, LIFO batch:15 [ 0.000000] AM335X ES1.0 (neon ) [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0933000 s9408 r8192 d15168 u32768 [ 0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc:
[ 0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] allocated 524288 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 255MB = 255MB total [ 0.000000] Memory: 238816k/238816k available, 23328k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB) [ 0.000000] .text : 0xc0008000 - 0xc0612cf0 (6188 kB) [ 0.000000] .init : 0xc0613000 - 0xc06554c0 ( 266 kB) [ 0.000000] .data : 0xc0656000 - 0xc06cc020 ( 473 kB) [ 0.000000] .bss : 0xc06cc020 - 0xc0725e3c ( 360 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000355] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968) [ 0.015436] pid_max: default: 32768 minimum: 301 [ 0.015666] Security Framework initialized [ 0.015760] Mount-cache hash table entries: 512 [ 0.024576] Initializing cgroup subsys cpuacct [ 0.024608] Initializing cgroup subsys memory [ 0.024672] Initializing cgroup subsys blkio [ 0.024810] CPU: Testing write buffer coherency: ok [ 0.025387] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.025462] Setting up static identity map for 0x8038c820 - 0x8038c86c [ 0.026786] Brought up 1 CPUs [ 0.026809] SMP: Total of 1 processors activated (545.07 BogoMIPS). [ 0.028108] devtmpfs: initialized [ 0.092507] pinctrl core: initialized pinctrl subsystem [ 0.092723] rstctl core: initialized rstctl subsystem [ 0.093216] regulator-dummy: no parameters [ 0.093786] NET: Registered protocol family 16 [ 0.094485] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.104156] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle [ 0.104337] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.105423] platform 49000000.edma: alias fck already exists [ 0.105457] platform 49000000.edma: alias fck already exists [ 0.105485] platform 49000000.edma: alias fck already exists [ 0.106631] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.106813] OMAP GPIO hardware version 0.1 [ 0.108218] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.109538] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.110857] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.111489] of_get_named_gpio_flags exited with status 52 [ 0.111520] gpio-rctrl rstctl.3: loaded OK [ 0.116621] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.119840] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.122032] cpsw.0: No hwaddr in dt. Using 90:70:65:3a:fc:95 from efuse [ 0.122064] cpsw.1: No hwaddr in dt. Using 90:70:65:3a:fc:97 from efuse [ 0.137611] bio: create slab <bio-0> at 0 [ 0.149741] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.149978] of_get_named_gpio_flags: can't parse gpios property [ 0.150268] vmmcsd_fixed: 3300 mV [ 0.153382] SCSI subsystem initialized [ 0.153835] usbcore: registered new interface driver usbfs [ 0.153949] usbcore: registered new interface driver hub [ 0.154282] usbcore: registered new device driver usb [ 0.156397] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz [ 0.156431] omap_i2c 4819c000.i2c: unable to select pin group [ 0.156625] media: Linux media interface: v0.10 [ 0.156720] Linux video capture interface: v2.00 [ 0.156835] pps_core: LinuxPPS API ver. 1 registered [ 0.156851] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.157567] Advanced Linux Sound Architecture Driver Initialized. [ 0.158757] Switching to clocksource gp_timer [ 0.176779] NET: Registered protocol family 2 [ 0.177771] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.177860] TCP bind hash table entries: 2048 (order: 3, 40960 bytes) [ 0.177950] TCP: Hash tables configured (established 2048 bind 2048) [ 0.178041] TCP: reno registered [ 0.178067] UDP hash table entries: 256 (order: 1, 12288 bytes) [ 0.178113] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) [ 0.178604] NET: Registered protocol family 1 [ 0.179184] RPC: Registered named UNIX socket transport module. [ 0.179206] RPC: Registered udp transport module. [ 0.179220] RPC: Registered tcp transport module. [ 0.179234] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.179620] Trying to unpack rootfs image as initramfs... [ 1.934038] Freeing initrd memory: 12100K [ 1.934760] CPU PMU: probing PMU on CPU 0 [ 1.934794] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 1.935327] omap2_mbox_probe: platform not supported [ 1.939167] VFS: Disk quotas dquot_6.5.2 [ 1.939404] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.940787] NFS: Registering the id_resolver key type [ 1.940878] Key type id_resolver registered [ 1.940895] Key type id_legacy registered [ 1.940962] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.941419] msgmni has been set to 490 [ 1.944342] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.944368] io scheduler noop registered [ 1.944385] io scheduler deadline registered [ 1.944442] io scheduler cfq registered (default) [ 1.948488] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.950932] omap_uart 44e09000.serial: did not get pins for uart0 error: -19 [ 1.951218] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0 [ 2.612043] console [ttyO0] enabled [ 2.616629] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1 [ 2.625295] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2 [ 2.633990] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4 [ 2.642612] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5 [ 2.651639] [drm] Initialized drm 1.1.0 20060810 [ 2.670237] brd: module loaded [ 2.680518] loop: module loaded [ 2.684745] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node [ 2.694700] nand_get_flash_type: 2c,da against 2c,da [ 2.700224] ONFI param page 0 valid [ 2.703896] ONFI flash detected [ 2.707216] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64 [ 2.719128] omap2-nand: detected x8 NAND flash [ 2.723795] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme [ 2.729379] omap2-nand: using custom ecc layout [ 2.734225] 10 ofpart partitions found on MTD device omap2-nand.0 [ 2.740621] Creating 10 MTD partitions on "omap2-nand.0": [ 2.746299] 0x000000000000-0x000000020000 : "spl" [ 2.753107] 0x000000020000-0x000000040000 : "spl_backup1" [ 2.760555] 0x000000040000-0x000000060000 : "spl_backup2" [ 2.767955] 0x000000060000-0x000000080000 : "spl_backup3" [ 2.775360] 0x000000080000-0x000000240000 : "u-boot" [ 2.783580] 0x000000240000-0x000000260000 : "bootenv" [ 2.790516] 0x000000260000-0x000000280000 : "fdt" [ 2.797123] 0x000000280000-0x000000780000 : "kernel" [ 2.808155] 0x000000800000-0x000001c00000 : "root" [ 2.831658] 0x000001c00000-0x000003000000 : "config" [ 2.855450] OneNAND driver initializing [ 2.861194] usbcore: registered new interface driver asix [ 2.867013] usbcore: registered new interface driver cdc_ether [ 2.873260] usbcore: registered new interface driver smsc95xx [ 2.879379] usbcore: registered new interface driver net1080 [ 2.885437] usbcore: registered new interface driver cdc_subset [ 2.891731] usbcore: registered new interface driver zaurus [ 2.897738] usbcore: registered new interface driver cdc_ncm [ 2.904464] usbcore: registered new interface driver cdc_acm [ 2.910425] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 2.918805] Initializing USB Mass Storage driver... [ 2.924044] usbcore: registered new interface driver usb-storage [ 2.930344] USB Mass Storage support registered. [ 2.935387] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 2.942139] musb-hdrc musb-hdrc.0.auto: pdev->id = 0 [ 2.947371] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.956142] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.956163] musb-hdrc: MHDRC RTL version 2.0 [ 2.956178] musb-hdrc: setup fifo_mode 4 [ 2.956206] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.956355] musb-hdrc musb-hdrc.0.auto: *** mode=3 [ 2.961399] musb-hdrc musb-hdrc.0.auto: *** power=250 [ 2.967471] musb-hdrc musb-hdrc.1.auto: pdev->id = 1 [ 2.972705] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.981475] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.981495] musb-hdrc: MHDRC RTL version 2.0 [ 2.981509] musb-hdrc: setup fifo_mode 4 [ 2.981531] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.981671] musb-hdrc musb-hdrc.1.auto: *** mode=1 [ 2.986715] musb-hdrc musb-hdrc.1.auto: *** power=250 [ 2.992023] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 2.998398] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 3.006867] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup [ 3.006974] usb usb1: default language 0x0409 [ 3.007032] usb usb1: udev 1, busnum 1, minor = 0 [ 3.007056] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.014198] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.021770] usb usb1: Product: MUSB HDRC host driver [ 3.026986] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd [ 3.032653] usb usb1: SerialNumber: musb-hdrc.1.auto [ 3.038639] usb usb1: usb_probe_device [ 3.038667] usb usb1: configuration #1 chosen from 1 choice [ 3.038732] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 3.038932] hub 1-0:1.0: usb_probe_interface [ 3.038955] hub 1-0:1.0: usb_probe_interface - got id [ 3.038982] hub 1-0:1.0: USB hub found [ 3.042986] hub 1-0:1.0: 1 port detected [ 3.047126] hub 1-0:1.0: standalone hub [ 3.047146] hub 1-0:1.0: individual port power switching [ 3.047164] hub 1-0:1.0: no over-current protection [ 3.047183] hub 1-0:1.0: Single TT [ 3.047204] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 3.047224] hub 1-0:1.0: power on to power good time: 10ms [ 3.047279] hub 1-0:1.0: local power source is good [ 3.047394] hub 1-0:1.0: enabling power on all ports [ 3.048479] mousedev: PS/2 mouse device common for all mice [ 3.056443] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 3.064210] i2c /dev entries driver [ 3.069283] pps_ldisc: PPS line discipline registered [ 3.074754] Driver for 1-wire Dallas network protocol. [ 3.082039] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 3.089609] cpuidle: using governor ladder [ 3.093937] cpuidle: using governor menu [ 3.098542] of_get_named_gpio_flags exited with status 6 [ 3.098562] of_get_named_gpio_flags: can't parse gpios property [ 3.098578] of_get_named_gpio_flags: can't parse gpios property [ 3.098615] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed [ 3.105847] omap_hsmmc mmc.4: Failed to get rstctl; not using any [ 3.112651] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 3.119889] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 3.127207] mmc.4 supply vmmc_aux not found, using dummy regulator [ 3.134148] omap_hsmmc mmc.4: pins are not configured from the driver [ 3.147257] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 3.167268] of_get_named_gpio_flags exited with status -517 [ 3.167335] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.175112] ledtrig-cpu: registered to indicate activity on CPUs [ 3.181888] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36 [ 3.189075] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 3.197164] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 3.203513] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 [ 3.210690] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 [ 3.222909] usbcore: registered new interface driver usbhid [ 3.228822] usbhid: USB HID core driver [ 3.235736] TCP: cubic registered [ 3.239263] Initializing XFRM netlink socket [ 3.243841] NET: Registered protocol family 17 [ 3.248651] NET: Registered protocol family 15 [ 3.253518] Key type dns_resolver registered [ 3.258164] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 3.266277] ThumbEE CPU extension supported. [ 3.270789] Registering SWP/SWPB emulation handler [ 3.276826] registered taskstats version 1 [ 3.283430] of_get_named_gpio_flags exited with status -517 [ 3.283504] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.340559] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 3.346972] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 3.361506] libphy: 4a101000.mdio: probed [ 3.365825] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 3.376064] Detected MACID = 90:70:65:3a:fc:95 [ 3.380751] cpsw 4a100000.ethernet: NAPI disabled [ 3.386146] of_get_named_gpio_flags exited with status -517 [ 3.386215] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.394949] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.404215] cpu0 supply cpu0 not found, using dummy regulator [ 3.410714] cpufreq_cpu0: failed to scale voltage up: -22 [ 3.416537] cpufreq_cpu0: failed to scale voltage up: -22 [ 3.429306] ALSA device list: [ 3.432536] No soundcards found. [ 3.437085] Freeing init memory: 264K [ 3.441141] Failed to execute /init [ 4.420461] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 5.720707] net eth0: initializing cpsw version 1.12 (0) [ 5.729673] net eth0: phy found : id is : 0x7c0f1 [ 5.735142] libphy: PHY 4a101000.mdio:01 not found [ 5.740321] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 9.876221] libphy: 4a101000.mdio:00 - Link is Up - 100/Full Dec 8 14:39:03 (none) local0.err cgminer: Miner compile time: Fri Aug 25 17:28:57 CST 2017 type: Antminer L3+ Dec 8 14:39:03 (none) local0.warn cgminer: Started cgminer 4.9.0 Dec 8 14:39:03 (none) local0.notice cgminer[378]: detected at /sys/class/gpio/gpio51/value chain 0 Dec 8 14:39:03 (none) local0.notice cgminer[378]: detect total chain num 1 Dec 8 14:39:03 (none) local0.notice cgminer[378]: i2c init ok Dec 8 14:39:05 (none) local0.notice cgminer[378]: Chain 0 PIC Version 0x3 Dec 8 14:39:05 (none) local0.err cgminer[378]: Blisssz: Chain not found 1 Dec 8 14:39:05 (none) local0.err cgminer[378]: Blisssz: Chain not found 2 Dec 8 14:39:05 (none) local0.err cgminer[378]: Blisssz: Chain not found 3 Dec 8 14:39:15 (none) local0.notice cgminer[378]: in tty_init Dec 8 14:39:15 (none) local0.notice cgminer[378]: tty_init 0 Dec 8 14:39:15 (none) local0.notice cgminer[378]: Start A New Asic Response.Chain Id:[0] Dec 8 14:39:15 (none) local0.notice cgminer[378]: open device over Dec 8 14:39:16 (none) local0.notice cgminer[378]: send cmd to get chip address Dec 8 14:39:18 (none) local0.notice cgminer[378]: Chain 0 ASIC 72 !!! Dec 8 14:39:18 (none) local0.notice cgminer[378]: addrInterval = '3' Dec 8 14:39:18 (none) local0.notice cgminer[378]: software_set_address: chain 0 has 72 ASIC, and addrInterval is 3 Dec 8 14:39:18 (none) local0.notice cgminer[378]: Now Set
Dec 8 14:39:18 (none) local0.notice cgminer[378]: software_set_address: chain 2 has 0 ASIC, and addrInterval is 3 Dec 8 14:39:18 (none) local0.notice cgminer[378]: software_set_address: chain 3 has 0 ASIC, and addrInterval is 3 Dec 8 14:39:19 (none) local0.notice cgminer[378]: frequency = '100' Dec 8 14:39:19 (none) local0.notice cgminer[378]: dev.timeout = 75 Dec 8 14:39:19 (none) local0.notice cgminer[378]: opt_bitmain_L3_core_temp : 2 Dec 8 14:39:19 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][16]@ChainID:[0], Chip[C] Dec 8 14:39:19 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][16]@ChainID:[0], Chip[C] Dec 8 14:39:20 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:20 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:20 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:20 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:20 (none) local0.err cgminer[378]: Get [1]Temp Data Failed! Dec 8 14:39:20 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][1][F3]@ChainID:[0], Chip[C] Dec 8 14:39:20 (none) local0.notice cgminer[378]: Chain 0 chip 0 RemoteTemp 0xfffffff3 Dec 8 14:39:21 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:21 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:21 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:21 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:21 (none) local0.notice cgminer[378]: 2 Chain 0 chip 0 local 0x16 remote 0xfffffff3 offset 0xffffffd8 Dec 8 14:39:21 (none) local0.notice cgminer[378]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0xffffffd8 Dec 8 14:39:22 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][11][FB]@ChainID:[0], Chip[C] Dec 8 14:39:22 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][16]@ChainID:[0], Chip[C] Dec 8 14:39:22 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][16]@ChainID:[0], Chip[C] Dec 8 14:39:22 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:22 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:22 (none) local0.err cgminer[378]: Get [1]Temp Data Failed! Dec 8 14:39:22 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:22 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:23 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][1][16]@ChainID:[0], Chip[C] Dec 8 14:39:23 (none) local0.notice cgminer[378]: Chain 0 chip 0 RemoteTemp 0x16 Dec 8 14:39:23 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:23 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:23 (none) local0.notice cgminer[378]: OK Chain 0 chip 0 local 0x16 remote 0x16 offset 0xfffffffb Dec 8 14:39:23 (none) local0.notice cgminer[378]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0xfffffff6 Dec 8 14:39:23 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:23 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:24 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][11][FB]@ChainID:[0], Chip[C] Dec 8 14:39:24 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][16]@ChainID:[0], Chip[C] Dec 8 14:39:24 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][16]@ChainID:[0], Chip[C] Dec 8 14:39:24 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][16]@ChainID:[0], Chip[C] Dec 8 14:39:25 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:25 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:25 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:25 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:25 (none) local0.err cgminer[378]: Get [1]Temp Data Failed! Dec 8 14:39:25 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][1][16]@ChainID:[0], Chip[C] Dec 8 14:39:25 (none) local0.notice cgminer[378]: Chain 0 chip 0 RemoteTemp 0x16 Dec 8 14:39:26 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:26 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:26 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:26 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:26 (none) local0.notice cgminer[378]: OK Chain 0 chip 0 local 0x16 remote 0x16 offset 0xfffffffb Dec 8 14:39:26 (none) local0.notice cgminer[378]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0x14 Dec 8 14:39:26 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][11][FB]@ChainID:[0], Chip[C] Dec 8 14:39:27 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][16]@ChainID:[0], Chip[C] Dec 8 14:39:27 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][16]@ChainID:[0], Chip[C] Dec 8 14:39:27 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:27 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:27 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:27 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:27 (none) local0.err cgminer[378]: Get [1]Temp Data Failed! Dec 8 14:39:28 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][1][16]@ChainID:[0], Chip[C] Dec 8 14:39:28 (none) local0.notice cgminer[378]: Chain 0 chip 0 RemoteTemp 0x16 Dec 8 14:39:28 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:28 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:28 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:28 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:28 (none) local0.notice cgminer[378]: OK Chain 0 chip 0 local 0x16 remote 0x16 offset 0xfffffffb Dec 8 14:39:28 (none) local0.notice cgminer[378]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0x32 Dec 8 14:39:29 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][11][FB]@ChainID:[0], Chip[C] Dec 8 14:39:29 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][16]@ChainID:[0], Chip[C] Dec 8 14:39:29 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][16]@ChainID:[0], Chip[C] Dec 8 14:39:29 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:29 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:30 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:30 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:30 (none) local0.err cgminer[378]: Get [1]Temp Data Failed! Dec 8 14:39:30 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][1][16]@ChainID:[0], Chip[C] Dec 8 14:39:30 (none) local0.notice cgminer[378]: Chain 0 chip 0 RemoteTemp 0x16 Dec 8 14:39:30 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:30 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:31 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:31 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:31 (none) local0.notice cgminer[378]: OK Chain 0 chip 0 local 0x16 remote 0x16 offset 0xfffffffb Dec 8 14:39:31 (none) local0.notice cgminer[378]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0x50 Dec 8 14:39:31 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][11][FB]@ChainID:[0], Chip[C] Dec 8 14:39:32 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:32 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:32 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:32 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:32 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:32 (none) local0.err cgminer[378]: Get [1]Temp Data Failed! Dec 8 14:39:32 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:33 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][1][16]@ChainID:[0], Chip[C] Dec 8 14:39:33 (none) local0.notice cgminer[378]: Chain 0 chip 0 RemoteTemp 0x16 Dec 8 14:39:33 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:33 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:33 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:33 (none) local0.notice cgminer[378]: OK Chain 0 chip 0 local 0x17 remote 0x16 offset 0xfffffffb Dec 8 14:39:33 (none) local0.notice cgminer[378]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0x6e Dec 8 14:39:33 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:34 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][11][FB]@ChainID:[0], Chip[C] Dec 8 14:39:34 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:34 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:34 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:34 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:34 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:35 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:35 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:35 (none) local0.err cgminer[378]: Get [1]Temp Data Failed! Dec 8 14:39:35 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][1][17]@ChainID:[0], Chip[C] Dec 8 14:39:35 (none) local0.notice cgminer[378]: Chain 0 chip 0 RemoteTemp 0x17 Dec 8 14:39:35 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:35 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:36 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:36 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:36 (none) local0.notice cgminer[378]: OK Chain 0 chip 0 local 0x17 remote 0x17 offset 0xfffffffb Dec 8 14:39:36 (none) local0.notice cgminer[378]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0xffffff8c Dec 8 14:39:36 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][11][FB]@ChainID:[0], Chip[C] Dec 8 14:39:37 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:37 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:37 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:37 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:37 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:37 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:37 (none) local0.err cgminer[378]: Get [1]Temp Data Failed! Dec 8 14:39:37 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][1][17]@ChainID:[0], Chip[C] Dec 8 14:39:38 (none) local0.notice cgminer[378]: Chain 0 chip 0 RemoteTemp 0x17 Dec 8 14:39:38 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:38 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:38 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:38 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:38 (none) local0.notice cgminer[378]: OK Chain 0 chip 0 local 0x17 remote 0x17 offset 0xfffffffb Dec 8 14:39:38 (none) local0.notice cgminer[378]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0xffffffaa Dec 8 14:39:39 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][11][FB]@ChainID:[0], Chip[C] Dec 8 14:39:39 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:39 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:39 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:39 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:40 (none) local0.err cgminer[378]: Get [1]Temp Data Failed! Dec 8 14:39:40 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:40 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:40 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][1][17]@ChainID:[0], Chip[C] Dec 8 14:39:40 (none) local0.notice cgminer[378]: Chain 0 chip 0 RemoteTemp 0x17 Dec 8 14:39:40 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:40 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:41 (none) local0.notice cgminer[378]: OK Chain 0 chip 0 local 0x17 remote 0x17 offset 0xfffffffb Dec 8 14:39:41 (none) local0.notice cgminer[378]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0xffffffc8 Dec 8 14:39:41 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:41 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:41 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][11][FB]@ChainID:[0], Chip[C] Dec 8 14:39:41 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:41 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:42 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:42 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:42 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:42 (none) local0.err cgminer[378]: Get [1]Temp Data Failed! Dec 8 14:39:42 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:42 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][1][17]@ChainID:[0], Chip[C] Dec 8 14:39:42 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][1][17]@ChainID:[0], Chip[C] Dec 8 14:39:42 (none) local0.notice cgminer[378]: Chain 0 chip 0 RemoteTemp 0x17 Dec 8 14:39:43 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:43 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:43 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:43 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:43 (none) local0.notice cgminer[378]: OK Chain 0 chip 0 local 0x17 remote 0x17 offset 0xfffffffb Dec 8 14:39:43 (none) local0.notice cgminer[378]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0xffffffe6 Dec 8 14:39:44 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][11][FB]@ChainID:[0], Chip[C] Dec 8 14:39:44 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:44 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][0][17]@ChainID:[0], Chip[C] Dec 8 14:39:44 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:44 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:45 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:45 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 14:39:45 (none) local0.err cgminer[378]: Get [1]Temp Data Failed! Dec 8 14:39:45 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][1][17]@ChainID:[0], Chip[C] Dec 8 14:39:45 (none) local0.notice cgminer[378]: Chain 0 chip 0 RemoteTemp 0x17 Dec 8 14:39:45 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:45 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:45 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:45 (none) local0.notice cgminer[378]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 14:39:45 (none) local0.notice cgminer[378]: OK Chain 0 chip 0 local 0x17 remote 0x17 offset 0xfffffffb Dec 8 14:39:45 (none) local0.notice cgminer[378]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0x4 Dec 8 14:39:46 (none) local0.notice cgminer[378]: send cmd to open block Dec 8 14:39:46 (none) local0.notice cgminer[378]: Dump IIC Data:[1][98][11][FB]@ChainID:[0], Chip[C] Dec 8 14:39:48 (none) local0.err cgminer[378]: cgminer time error total_secs = 1512743988.584983 last_total_secs = 1.000000 Dec 8 14:39:51 (none) local0.warn cgminer[378]: Pool 1 stratum+tcp://stratum-ltc.antpool.com:443 alive, testing stability Dec 8 14:39:51 (none) local0.warn cgminer[378]: Switching to pool 1 stratum+tcp://stratum-ltc.antpool.com:443 Dec 8 14:39:52 (none) local0.warn cgminer[378]: Pool 0 stratum+tcp://stratum-ltc.antpool.com:8888 alive, testing stability Dec 8 14:39:52 (none) local0.warn cgminer[378]: Switching to pool 0 stratum+tcp://stratum-ltc.antpool.com:8888 Dec 8 14:39:56 (none) local0.warn cgminer[378]: API running in IP access mode on port 4028 (15) http://i65.tinypic.com/a2pvmx.png It worked!!! You are awesome!!! What should I do next? Title: Re: Issue new antminer l3+ Post by: blissz on December 08, 2017, 02:48:51 PM Wooop woop ;D
Now shutdown and disconnect the first (working) chain and connect the next one to the first connector. So you flash them one by one. When you got them all flashed, just flash back to the stock firmware and connect everything like it was before and it should be running like normal again. Title: Re: Issue new antminer l3+ Post by: playboy333 on December 08, 2017, 04:20:26 PM Wooop woop ;D Now shutdown and disconnect the first (working) chain and connect the next one to the first connector. So you flash them one by one. When you got them all flashed, just flash back to the stock firmware and connect everything like it was before and it should be running like normal again. I did as you adviced. The only last hashboard did not want to be flashed. I tried everything - chaned cable to another one and changed chain to another one. But it did not work. Code: [ 0.000000] Booting Linux on physical CPU 0x0 Title: Re: Issue new antminer l3+ Post by: blissz on December 08, 2017, 04:25:25 PM Ok I will have a look at this a bit later. I have some work to do on the d3 firmware first. For now: flash to stock firmware and mine with 3 instead of 4 chains. Just don't connect that one chain.
Title: Re: Issue new antminer l3+ Post by: playboy333 on December 08, 2017, 04:30:42 PM Ok I will have a look at this a bit later. I have some work to do on the d3 firmware first. For now: flash to stock firmware and mine with 3 instead of 4 chains. Just don't connect that one chain. And finally, I flashed it back to stock fw as you said. [code] [ 3.419582] ALSA device list: [ 3.422811] No soundcards found. [ 3.427361] Freeing init memory: 264K [ 3.431419] Failed to execute /init [ 4.407827] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 5.701685] net eth0: initializing cpsw version 1.12 (0) [ 5.710617] net eth0: phy found : id is : 0x7c0f1 [ 5.716098] libphy: PHY 4a101000.mdio:01 not found [ 5.721298] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 9.856709] libphy: 4a101000.mdio:00 - Link is Up - 100/Full Dec 8 15:55:24 (none) local0.err cgminer: Miner compile time: Fri Aug 25 17:28:57 CST 2017 type: Antminer L3+ Dec 8 15:55:24 (none) local0.warn cgminer: Started cgminer 4.9.0 Dec 8 15:55:24 (none) local0.notice cgminer[375]: detected at /sys/class/gpio/gpio51/value chain 0 Dec 8 15:55:24 (none) local0.notice cgminer[375]: detected at /sys/class/gpio/gpio48/value chain 1 Dec 8 15:55:24 (none) local0.notice cgminer[375]: detected at /sys/class/gpio/gpio47/value chain 2 Dec 8 15:55:24 (none) local0.notice cgminer[375]: detected at /sys/class/gpio/gpio44/value chain 3 Dec 8 15:55:24 (none) local0.notice cgminer[375]: detect total chain num 4 Dec 8 15:55:24 (none) local0.notice cgminer[375]: i2c init ok Dec 8 15:55:34 (none) local0.notice cgminer[375]: in tty_init Dec 8 15:55:34 (none) local0.notice cgminer[375]: tty_init 0 Dec 8 15:55:34 (none) local0.notice cgminer[375]: Start A New Asic Response.Chain Id:[0] Dec 8 15:55:34 (none) local0.notice cgminer[375]: tty_init 1 Dec 8 15:55:34 (none) local0.notice cgminer[375]: Start A New Asic Response.Chain Id:[1] Dec 8 15:55:34 (none) local0.notice cgminer[375]: tty_init 2 Dec 8 15:55:34 (none) local0.notice cgminer[375]: Start A New Asic Response.Chain Id:[2] Dec 8 15:55:35 (none) local0.notice cgminer[375]: tty_init 3 Dec 8 15:55:35 (none) local0.notice cgminer[375]: Start A New Asic Response.Chain Id:[3] Dec 8 15:55:35 (none) local0.notice cgminer[375]: open device over Dec 8 15:55:35 (none) local0.notice cgminer[375]: send cmd to get chip address Dec 8 15:55:37 (none) local0.notice cgminer[375]: Chain 0 ASIC 72 !!! Dec 8 15:55:37 (none) local0.notice cgminer[375]: Chain 1 ASIC 72 !!! Dec 8 15:55:37 (none) local0.notice cgminer[375]: Chain 2 ASIC 72 !!! Dec 8 15:55:37 (none) local0.notice cgminer[375]: Chain 3 ASIC 0 !!! Dec 8 15:55:37 (none) local0.notice cgminer[375]: Need to recheck asic num !!! Dec 8 15:55:45 (none) local0.err cgminer: Miner compile time: Fri Aug 25 17:28:57 CST 2017 type: Antminer L3+ Dec 8 15:55:45 (none) local0.warn cgminer: Started cgminer 4.9.0 Dec 8 15:55:45 (none) local0.notice cgminer[670]: detected at /sys/class/gpio/gpio51/value chain 0 Dec 8 15:55:45 (none) local0.notice cgminer[670]: detected at /sys/class/gpio/gpio48/value chain 1 Dec 8 15:55:45 (none) local0.notice cgminer[670]: detected at /sys/class/gpio/gpio47/value chain 2 Dec 8 15:55:45 (none) local0.notice cgminer[670]: detected at /sys/class/gpio/gpio44/value chain 3 Dec 8 15:55:45 (none) local0.notice cgminer[670]: detect total chain num 4 Dec 8 15:55:45 (none) local0.notice cgminer[670]: i2c init ok Dec 8 15:55:54 (none) local0.notice cgminer[670]: in tty_init Dec 8 15:55:54 (none) local0.notice cgminer[670]: tty_init 0 Dec 8 15:55:54 (none) local0.notice cgminer[670]: Start A New Asic Response.Chain Id:[0] Dec 8 15:55:55 (none) local0.notice cgminer[670]: tty_init 1 Dec 8 15:55:55 (none) local0.notice cgminer[670]: Start A New Asic Response.Chain Id:[1] Dec 8 15:55:55 (none) local0.notice cgminer[670]: tty_init 2 Dec 8 15:55:55 (none) local0.notice cgminer[670]: Start A New Asic Response.Chain Id:[2] Dec 8 15:55:55 (none) local0.notice cgminer[670]: tty_init 3 Dec 8 15:55:55 (none) local0.notice cgminer[670]: Start A New Asic Response.Chain Id:[3] Dec 8 15:55:55 (none) local0.notice cgminer[670]: open device over Dec 8 15:55:55 (none) local0.notice cgminer[670]: send cmd to get chip address Dec 8 15:55:57 (none) local0.notice cgminer[670]: Chain 0 ASIC 72 !!! Dec 8 15:55:57 (none) local0.notice cgminer[670]: Chain 1 ASIC 72 !!! Dec 8 15:55:57 (none) local0.notice cgminer[670]: Chain 2 ASIC 72 !!! Dec 8 15:55:57 (none) local0.notice cgminer[670]: Chain 3 ASIC 0 !!! Dec 8 15:55:57 (none) local0.notice cgminer[670]: Need to recheck asic num !!! Dec 8 15:55:59 (none) local0.notice cgminer[670]: Chain 0 ASIC 72 !!! Dec 8 15:55:59 (none) local0.notice cgminer[670]: Chain 1 ASIC 72 !!! Dec 8 15:55:59 (none) local0.notice cgminer[670]: Chain 2 ASIC 72 !!! Dec 8 15:55:59 (none) local0.notice cgminer[670]: Chain 3 ASIC 0 !!! Dec 8 15:55:59 (none) local0.notice cgminer[670]: Need to recheck asic num !!! Dec 8 15:56:01 (none) local0.notice cgminer[670]: Chain 0 ASIC 72 !!! Dec 8 15:56:01 (none) local0.notice cgminer[670]: Chain 1 ASIC 72 !!! Dec 8 15:56:01 (none) local0.notice cgminer[670]: Chain 2 ASIC 72 !!! Dec 8 15:56:01 (none) local0.notice cgminer[670]: Chain 3 ASIC 0 !!! Dec 8 15:56:01 (none) local0.notice cgminer[670]: Need to recheck asic num !!! Dec 8 15:56:04 (none) local0.notice cgminer[670]: Chain 0 ASIC 72 !!! Dec 8 15:56:04 (none) local0.notice cgminer[670]: Chain 1 ASIC 72 !!! Dec 8 15:56:04 (none) local0.notice cgminer[670]: Chain 2 ASIC 72 !!! Dec 8 15:56:04 (none) local0.notice cgminer[670]: Chain 3 ASIC 0 !!! Dec 8 15:56:04 (none) local0.notice cgminer[670]: Need to recheck asic num !!! Dec 8 15:56:06 (none) local0.notice cgminer[670]: Chain 0 ASIC 72 !!! Dec 8 15:56:06 (none) local0.notice cgminer[670]: Chain 1 ASIC 72 !!! Dec 8 15:56:06 (none) local0.notice cgminer[670]: Chain 2 ASIC 72 !!! Dec 8 15:56:06 (none) local0.notice cgminer[670]: Chain 3 ASIC 0 !!! Dec 8 15:56:06 (none) local0.notice cgminer[670]: Need to recheck asic num !!! Dec 8 15:56:08 (none) local0.notice cgminer[670]: Chain 0 ASIC 72 !!! Dec 8 15:56:08 (none) local0.notice cgminer[670]: Chain 1 ASIC 72 !!! Dec 8 15:56:08 (none) local0.notice cgminer[670]: Chain 2 ASIC 72 !!! Dec 8 15:56:08 (none) local0.notice cgminer[670]: Chain 3 ASIC 0 !!! Dec 8 15:56:08 (none) local0.notice cgminer[670]: addrInterval = '3' Dec 8 15:56:08 (none) local0.notice cgminer[670]: software_set_address: chain 0 has 72 ASIC, and addrInterval is 3 Dec 8 15:56:08 (none) local0.notice cgminer[670]: Now Set
Dec 8 15:56:09 (none) local0.notice cgminer[670]: Now Set [1] Chain Address Dec 8 15:56:10 (none) local0.notice cgminer[670]: software_set_address: chain 2 has 72 ASIC, and addrInterval is 3 Dec 8 15:56:10 (none) local0.notice cgminer[670]: Now Set [2] Chain Address Dec 8 15:56:11 (none) local0.notice cgminer[670]: software_set_address: chain 3 has 0 ASIC, and addrInterval is 3 Dec 8 15:56:11 (none) local0.notice cgminer[670]: Now Set [3] Chain Address Dec 8 15:56:12 (none) local0.notice cgminer[670]: frequency = '384' Dec 8 15:56:12 (none) local0.notice cgminer[670]: dev.timeout = 19 Dec 8 15:56:12 (none) local0.notice cgminer[670]: opt_bitmain_L3_core_temp : 2 Dec 8 15:56:12 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1C]@ChainID:[0], Chip[C] Dec 8 15:56:12 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[1], Chip[C] Dec 8 15:56:12 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[2], Chip[C] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:13 (none) local0.err cgminer[670]: Get [1]Temp Data Failed! Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][F8]@ChainID:[0], Chip[C] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][F9]@ChainID:[1], Chip[C] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][F8]@ChainID:[2], Chip[C] Dec 8 15:56:13 (none) local0.notice cgminer[670]: Chain 0 chip 0 RemoteTemp 0xfffffff8 Dec 8 15:56:13 (none) local0.notice cgminer[670]: Chain 1 chip 0 RemoteTemp 0xfffffff9 Dec 8 15:56:13 (none) local0.notice cgminer[670]: Chain 2 chip 0 RemoteTemp 0xfffffff8 Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:14 (none) local0.notice cgminer[670]: 2 Chain 0 chip 0 local 0x1c remote 0xfffffff8 offset 0xffffffd8 Dec 8 15:56:14 (none) local0.notice cgminer[670]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0xffffffd8 Dec 8 15:56:14 (none) local0.notice cgminer[670]: 2 Chain 1 chip 0 local 0x1b remote 0xfffffff9 offset 0xffffffd8 Dec 8 15:56:14 (none) local0.notice cgminer[670]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0xffffffd8 Dec 8 15:56:14 (none) local0.notice cgminer[670]: 2 Chain 2 chip 0 local 0x19 remote 0xfffffff8 offset 0xffffffd8 Dec 8 15:56:14 (none) local0.notice cgminer[670]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0xffffffd8 Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FC]@ChainID:[0], Chip[C] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FA]@ChainID:[1], Chip[C] Dec 8 15:56:14 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][F9]@ChainID:[2], Chip[C] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[0], Chip[C] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[1], Chip[C] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[2], Chip[C] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[0], Chip[C] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[1], Chip[C] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[2], Chip[C] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:15 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:15 (none) local0.err cgminer[670]: Get [1]Temp Data Failed! Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1C]@ChainID:[0], Chip[C] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1B]@ChainID:[1], Chip[C] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][19]@ChainID:[2], Chip[C] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Chain 0 chip 0 RemoteTemp 0x1c Dec 8 15:56:16 (none) local0.notice cgminer[670]: Chain 1 chip 0 RemoteTemp 0x1b Dec 8 15:56:16 (none) local0.notice cgminer[670]: Chain 2 chip 0 RemoteTemp 0x19 Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:16 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:16 (none) local0.notice cgminer[670]: OK Chain 0 chip 0 local 0x1b remote 0x1c offset 0xfffffffc Dec 8 15:56:16 (none) local0.notice cgminer[670]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0xfffffff6 Dec 8 15:56:16 (none) local0.notice cgminer[670]: OK Chain 1 chip 0 local 0x1b remote 0x1b offset 0xfffffffa Dec 8 15:56:16 (none) local0.notice cgminer[670]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0xfffffff6 Dec 8 15:56:16 (none) local0.notice cgminer[670]: OK Chain 2 chip 0 local 0x19 remote 0x19 offset 0xfffffff9 Dec 8 15:56:16 (none) local0.notice cgminer[670]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0xfffffff6 Dec 8 15:56:17 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FC]@ChainID:[0], Chip[C] Dec 8 15:56:17 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FA]@ChainID:[1], Chip[C] Dec 8 15:56:17 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][F9]@ChainID:[2], Chip[C] Dec 8 15:56:17 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[0], Chip[C] Dec 8 15:56:17 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[1], Chip[C] Dec 8 15:56:17 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[2], Chip[C] Dec 8 15:56:17 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[0], Chip[C] Dec 8 15:56:17 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[1], Chip[C] Dec 8 15:56:17 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[2], Chip[C] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:18 (none) local0.err cgminer[670]: Get [1]Temp Data Failed! Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1C]@ChainID:[0], Chip[C] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1B]@ChainID:[1], Chip[C] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][18]@ChainID:[2], Chip[C] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Chain 0 chip 0 RemoteTemp 0x1c Dec 8 15:56:18 (none) local0.notice cgminer[670]: Chain 1 chip 0 RemoteTemp 0x1b Dec 8 15:56:18 (none) local0.notice cgminer[670]: Chain 2 chip 0 RemoteTemp 0x18 Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:18 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:19 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:19 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:19 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:19 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:19 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:19 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:19 (none) local0.notice cgminer[670]: OK Chain 0 chip 0 local 0x1b remote 0x1c offset 0xfffffffc Dec 8 15:56:19 (none) local0.notice cgminer[670]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0x14 Dec 8 15:56:19 (none) local0.notice cgminer[670]: OK Chain 1 chip 0 local 0x1b remote 0x1b offset 0xfffffffa Dec 8 15:56:19 (none) local0.notice cgminer[670]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0x14 Dec 8 15:56:19 (none) local0.notice cgminer[670]: OK Chain 2 chip 0 local 0x19 remote 0x18 offset 0xfffffff9 Dec 8 15:56:19 (none) local0.notice cgminer[670]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0x14 Dec 8 15:56:19 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FC]@ChainID:[0], Chip[C] Dec 8 15:56:19 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FA]@ChainID:[1], Chip[C] Dec 8 15:56:19 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][F9]@ChainID:[2], Chip[C] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[0], Chip[C] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[1], Chip[C] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[2], Chip[C] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[0], Chip[C] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[1], Chip[C] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[2], Chip[C] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:20 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:20 (none) local0.err cgminer[670]: Get [1]Temp Data Failed! Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1B]@ChainID:[0], Chip[C] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1A]@ChainID:[1], Chip[C] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][18]@ChainID:[2], Chip[C] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Chain 0 chip 0 RemoteTemp 0x1b Dec 8 15:56:21 (none) local0.notice cgminer[670]: Chain 1 chip 0 RemoteTemp 0x1a Dec 8 15:56:21 (none) local0.notice cgminer[670]: Chain 2 chip 0 RemoteTemp 0x18 Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:21 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:21 (none) local0.notice cgminer[670]: OK Chain 0 chip 0 local 0x1b remote 0x1b offset 0xfffffffc Dec 8 15:56:21 (none) local0.notice cgminer[670]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0x32 Dec 8 15:56:21 (none) local0.notice cgminer[670]: OK Chain 1 chip 0 local 0x1a remote 0x1a offset 0xfffffffa Dec 8 15:56:21 (none) local0.notice cgminer[670]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0x32 Dec 8 15:56:21 (none) local0.notice cgminer[670]: OK Chain 2 chip 0 local 0x19 remote 0x18 offset 0xfffffff9 Dec 8 15:56:21 (none) local0.notice cgminer[670]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0x32 Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FC]@ChainID:[0], Chip[C] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FA]@ChainID:[1], Chip[C] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][F9]@ChainID:[2], Chip[C] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[0], Chip[C] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[1], Chip[C] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[2], Chip[C] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1B]@ChainID:[0], Chip[C] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[1], Chip[C] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[2], Chip[C] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:22 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:23 (none) local0.err cgminer[670]: Get [1]Temp Data Failed! Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1B]@ChainID:[0], Chip[C] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1A]@ChainID:[1], Chip[C] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][18]@ChainID:[2], Chip[C] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Chain 0 chip 0 RemoteTemp 0x1b Dec 8 15:56:23 (none) local0.notice cgminer[670]: Chain 1 chip 0 RemoteTemp 0x1a Dec 8 15:56:23 (none) local0.notice cgminer[670]: Chain 2 chip 0 RemoteTemp 0x18 Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:23 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:24 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:24 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:24 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:24 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:24 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:24 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:24 (none) local0.notice cgminer[670]: OK Chain 0 chip 0 local 0x1b remote 0x1b offset 0xfffffffc Dec 8 15:56:24 (none) local0.notice cgminer[670]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0x50 Dec 8 15:56:24 (none) local0.notice cgminer[670]: OK Chain 1 chip 0 local 0x1a remote 0x1a offset 0xfffffffa Dec 8 15:56:24 (none) local0.notice cgminer[670]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0x50 Dec 8 15:56:24 (none) local0.notice cgminer[670]: OK Chain 2 chip 0 local 0x19 remote 0x18 offset 0xfffffff9 Dec 8 15:56:24 (none) local0.notice cgminer[670]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0x50 Dec 8 15:56:24 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FC]@ChainID:[0], Chip[C] Dec 8 15:56:24 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FA]@ChainID:[1], Chip[C] Dec 8 15:56:24 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][F9]@ChainID:[2], Chip[C] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[0], Chip[C] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[1], Chip[C] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][18]@ChainID:[2], Chip[C] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[0], Chip[C] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[1], Chip[C] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][18]@ChainID:[2], Chip[C] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:25 (none) local0.err cgminer[670]: Get [1]Temp Data Failed! Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1B]@ChainID:[0], Chip[C] Dec 8 15:56:25 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1A]@ChainID:[1], Chip[C] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][18]@ChainID:[2], Chip[C] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Chain 0 chip 0 RemoteTemp 0x1b Dec 8 15:56:26 (none) local0.notice cgminer[670]: Chain 1 chip 0 RemoteTemp 0x1a Dec 8 15:56:26 (none) local0.notice cgminer[670]: Chain 2 chip 0 RemoteTemp 0x18 Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:26 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:26 (none) local0.notice cgminer[670]: OK Chain 0 chip 0 local 0x1a remote 0x1b offset 0xfffffffc Dec 8 15:56:26 (none) local0.notice cgminer[670]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0x6e Dec 8 15:56:26 (none) local0.notice cgminer[670]: OK Chain 1 chip 0 local 0x1a remote 0x1a offset 0xfffffffa Dec 8 15:56:26 (none) local0.notice cgminer[670]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0x6e Dec 8 15:56:26 (none) local0.notice cgminer[670]: OK Chain 2 chip 0 local 0x18 remote 0x18 offset 0xfffffff9 Dec 8 15:56:26 (none) local0.notice cgminer[670]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0x6e Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FC]@ChainID:[0], Chip[C] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FA]@ChainID:[1], Chip[C] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][F9]@ChainID:[2], Chip[C] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[0], Chip[C] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[1], Chip[C] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][18]@ChainID:[2], Chip[C] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[0], Chip[C] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[1], Chip[C] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][18]@ChainID:[2], Chip[C] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:27 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:28 (none) local0.err cgminer[670]: Get [1]Temp Data Failed! Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1B]@ChainID:[0], Chip[C] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1A]@ChainID:[1], Chip[C] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][18]@ChainID:[2], Chip[C] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1B]@ChainID:[0], Chip[C] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1A]@ChainID:[1], Chip[C] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][18]@ChainID:[2], Chip[C] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1B]@ChainID:[0], Chip[C] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1A]@ChainID:[1], Chip[C] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][18]@ChainID:[2], Chip[C] Dec 8 15:56:28 (none) local0.notice cgminer[670]: Chain 0 chip 0 RemoteTemp 0x1b Dec 8 15:56:28 (none) local0.notice cgminer[670]: Chain 1 chip 0 RemoteTemp 0x1a Dec 8 15:56:28 (none) local0.notice cgminer[670]: Chain 2 chip 0 RemoteTemp 0x18 Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:29 (none) local0.notice cgminer[670]: OK Chain 0 chip 0 local 0x1a remote 0x1b offset 0xfffffffc Dec 8 15:56:29 (none) local0.notice cgminer[670]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0xffffff8c Dec 8 15:56:29 (none) local0.notice cgminer[670]: OK Chain 1 chip 0 local 0x1a remote 0x1a offset 0xfffffffa Dec 8 15:56:29 (none) local0.notice cgminer[670]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0xffffff8c Dec 8 15:56:29 (none) local0.notice cgminer[670]: OK Chain 2 chip 0 local 0x18 remote 0x18 offset 0xfffffff9 Dec 8 15:56:29 (none) local0.notice cgminer[670]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0xffffff8c Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FC]@ChainID:[0], Chip[C] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FA]@ChainID:[1], Chip[C] Dec 8 15:56:29 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][F9]@ChainID:[2], Chip[C] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[0], Chip[C] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[1], Chip[C] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][18]@ChainID:[2], Chip[C] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[0], Chip[C] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[1], Chip[C] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][18]@ChainID:[2], Chip[C] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:30 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:30 (none) local0.err cgminer[670]: Get [1]Temp Data Failed! Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1B]@ChainID:[0], Chip[C] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][19]@ChainID:[1], Chip[C] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][18]@ChainID:[2], Chip[C] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Chain 0 chip 0 RemoteTemp 0x1b Dec 8 15:56:31 (none) local0.notice cgminer[670]: Chain 1 chip 0 RemoteTemp 0x19 Dec 8 15:56:31 (none) local0.notice cgminer[670]: Chain 2 chip 0 RemoteTemp 0x18 Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:31 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:31 (none) local0.notice cgminer[670]: OK Chain 0 chip 0 local 0x1a remote 0x1b offset 0xfffffffc Dec 8 15:56:31 (none) local0.notice cgminer[670]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0xffffffaa Dec 8 15:56:31 (none) local0.notice cgminer[670]: OK Chain 1 chip 0 local 0x1a remote 0x19 offset 0xfffffffa Dec 8 15:56:31 (none) local0.notice cgminer[670]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0xffffffaa Dec 8 15:56:31 (none) local0.notice cgminer[670]: OK Chain 2 chip 0 local 0x18 remote 0x18 offset 0xfffffff9 Dec 8 15:56:31 (none) local0.notice cgminer[670]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0xffffffaa Dec 8 15:56:32 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FC]@ChainID:[0], Chip[C] Dec 8 15:56:32 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FA]@ChainID:[1], Chip[C] Dec 8 15:56:32 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][F9]@ChainID:[2], Chip[C] Dec 8 15:56:32 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[0], Chip[C] Dec 8 15:56:32 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[1], Chip[C] Dec 8 15:56:32 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][18]@ChainID:[2], Chip[C] Dec 8 15:56:32 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[0], Chip[C] Dec 8 15:56:32 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[1], Chip[C] Dec 8 15:56:32 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][18]@ChainID:[2], Chip[C] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:33 (none) local0.err cgminer[670]: Get [1]Temp Data Failed! Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1B]@ChainID:[0], Chip[C] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][19]@ChainID:[1], Chip[C] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][17]@ChainID:[2], Chip[C] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Chain 0 chip 0 RemoteTemp 0x1b Dec 8 15:56:33 (none) local0.notice cgminer[670]: Chain 1 chip 0 RemoteTemp 0x19 Dec 8 15:56:33 (none) local0.notice cgminer[670]: Chain 2 chip 0 RemoteTemp 0x17 Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:33 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:34 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:34 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:34 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:34 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:34 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:34 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:34 (none) local0.notice cgminer[670]: OK Chain 0 chip 0 local 0x1a remote 0x1b offset 0xfffffffc Dec 8 15:56:34 (none) local0.notice cgminer[670]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0xffffffc8 Dec 8 15:56:34 (none) local0.notice cgminer[670]: OK Chain 1 chip 0 local 0x19 remote 0x19 offset 0xfffffffa Dec 8 15:56:34 (none) local0.notice cgminer[670]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0xffffffc8 Dec 8 15:56:34 (none) local0.notice cgminer[670]: OK Chain 2 chip 0 local 0x18 remote 0x17 offset 0xfffffff9 Dec 8 15:56:34 (none) local0.notice cgminer[670]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0xffffffc8 Dec 8 15:56:34 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FC]@ChainID:[0], Chip[C] Dec 8 15:56:34 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FA]@ChainID:[1], Chip[C] Dec 8 15:56:34 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][F9]@ChainID:[2], Chip[C] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[0], Chip[C] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[1], Chip[C] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][18]@ChainID:[2], Chip[C] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[0], Chip[C] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[1], Chip[C] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][18]@ChainID:[2], Chip[C] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:35 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:35 (none) local0.err cgminer[670]: Get [1]Temp Data Failed! Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1A]@ChainID:[0], Chip[C] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][19]@ChainID:[1], Chip[C] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][17]@ChainID:[2], Chip[C] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1A]@ChainID:[0], Chip[C] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][19]@ChainID:[1], Chip[C] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][17]@ChainID:[2], Chip[C] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1A]@ChainID:[0], Chip[C] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][19]@ChainID:[1], Chip[C] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][17]@ChainID:[2], Chip[C] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Chain 0 chip 0 RemoteTemp 0x1a Dec 8 15:56:36 (none) local0.notice cgminer[670]: Chain 1 chip 0 RemoteTemp 0x19 Dec 8 15:56:36 (none) local0.notice cgminer[670]: Chain 2 chip 0 RemoteTemp 0x17 Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:36 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:37 (none) local0.notice cgminer[670]: OK Chain 0 chip 0 local 0x1a remote 0x1a offset 0xfffffffc Dec 8 15:56:37 (none) local0.notice cgminer[670]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0xffffffe6 Dec 8 15:56:37 (none) local0.notice cgminer[670]: OK Chain 1 chip 0 local 0x19 remote 0x19 offset 0xfffffffa Dec 8 15:56:37 (none) local0.notice cgminer[670]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0xffffffe6 Dec 8 15:56:37 (none) local0.notice cgminer[670]: OK Chain 2 chip 0 local 0x18 remote 0x17 offset 0xfffffff9 Dec 8 15:56:37 (none) local0.notice cgminer[670]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0xffffffe6 Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FC]@ChainID:[0], Chip[C] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][FA]@ChainID:[1], Chip[C] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][11][F9]@ChainID:[2], Chip[C] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[0], Chip[C] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[1], Chip[C] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][18]@ChainID:[2], Chip[C] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][1A]@ChainID:[0], Chip[C] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][19]@ChainID:[1], Chip[C] Dec 8 15:56:37 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][0][18]@ChainID:[2], Chip[C] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9] Dec 8 15:56:38 (none) local0.err cgminer[670]: Get [1]Temp Data Failed! Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][1A]@ChainID:[0], Chip[C] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][19]@ChainID:[1], Chip[C] Dec 8 15:56:38 (none) local0.notice cgminer[670]: Dump IIC Data:[1][98][1][17]@ChainID:[2], Chip[C] Dec 8 15:56:39 (none) local0.notice cgminer[670]: Chain 0 chip 0 RemoteTemp 0x1a Dec 8 15:56:39 (none) local0.notice cgminer[670]: Chain 1 chip 0 RemoteTemp 0x19 Dec 8 15:56:39 (none) local0.notice cgminer[670]: Chain 2 chip 0 RemoteTemp 0x17 Dec 8 15:56:39 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:39 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:39 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:39 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:39 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:39 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:39 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:39 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:39 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:39 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9] Dec 8 15:56:39 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9] Dec 8 15:56:39 (none) local0.notice cgminer[670]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9] Dec 8 15:56:39 (none) local0.notice cgminer[670]: OK Chain 0 chip 0 local 0x1a remote 0x1a offset 0xfffffffc Dec 8 15:56:39 (none) local0.notice cgminer[670]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0x4 Dec 8 15:56:39 (none) local0.notice cgminer[670]: OK Chain 1 chip 0 local 0x19 remote 0x19 offset 0xfffffffa Dec 8 15:56:39 (none) local0.notice cgminer[670]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0x4 Dec 8 15:56:39 (none) local0.notice cgminer[670]: OK Chain 2 c Title: Re: Issue new antminer l3+ Post by: blissz on December 08, 2017, 04:33:57 PM hmmz lots of weird stuff going still. Does it mine? Otherwise with the 3 working chains connected try the fix2 firmware...
Title: Re: Issue new antminer l3+ Post by: playboy333 on December 08, 2017, 04:39:09 PM Ok I will have a look at this a bit later. I have some work to do on the d3 firmware first. For now: flash to stock firmware and mine with 3 instead of 4 chains. Just don't connect that one chain. This is the ending of the log under stock fw. Code: Dec 8 15:56:19 (none) local0.notice cgminer[670]: OK Chain 0 chip 0 local 0x1b remote 0x1c offset 0xfffffffc https://imgur.com/a/TWdZQ Thank you soooo much!!! Looking forward for your advices:) Title: Re: Issue new antminer l3+ Post by: playboy333 on December 08, 2017, 04:48:51 PM hmmz lots of weird stuff going still. Does it mine? Otherwise with the 3 working chains connected try the fix2 firmware... I did as you adviced. I flashed your fix fw over stock fw with 3 working boards.Code: [ 3.435199] ALSA device list: https://imgur.com/a/eY2Cm Title: Re: Issue new antminer l3+ Post by: gians82 on December 08, 2017, 06:36:05 PM You're the number one, everything works. thanks thanks thanks ;D ;D ;D ;D
Title: Re: Issue new antminer l3+ Post by: blissz on December 08, 2017, 10:16:51 PM I am glad at least it helps a bit for you guys! I can imagine it's very annoying having a miner doing nothing... Still strange why one of the 4 boards is having a problem still for two of you now. If I find some more time for it I will dive into it
Title: Re: Issue new antminer l3+ Post by: cryptonitro on December 09, 2017, 12:35:08 AM ok if i m right we have for now to flash one by one.
i was went at job after the 1st test. ! will try that tomorrow it s too late 1h30 AM here ... I will edit the 1st post , once we have that fix , for easy find for futur readers with this problem blissz , thumb up as usualy would like to send donation to you , xrp adress may be ? fast and cheap fee or else if you have one favorite (mp me) @playboy333 thanks for call the test , wondering why is only 30mhs / board on your screen? Title: Re: Issue new antminer l3+ Post by: CryptoWatcher420 on December 09, 2017, 01:11:25 AM what rom flashing tool did you use? PICkit3ebay or amazon? Title: Re: Issue new antminer l3+ Post by: cryptonitro on December 09, 2017, 09:56:34 AM what rom flashing tool did you use? PICkit3ebay or amazon? please read we have a temporary solution actually, with flashing firmware of blissz only 3 board let me think about the D3 with have only 3 boards may be BB board got bad things to:'( Title: Re: Issue new antminer l3+ Post by: blissz on December 09, 2017, 10:11:46 AM ok if i m right we have for now to flash one by one. i was went at job after the 1st test. ! will try that tomorrow it s too late 1h30 AM here ... I will edit the 1st post , once we have that fix , for easy find for futur readers with this problem blissz , thumb up as usualy would like to send donation to you , xrp adress may be ? fast and cheap fee or else if you have one favorite (mp me) @playboy333 thanks for call the test , wondering why is only 30mhs / board on your screen? Although it was not that smart maybe, it was my firmware that caused it in the end, so I am glad I could help. There is no need for a donation, but thanks ;) Title: Re: Issue new antminer l3+ Post by: cryptonitro on December 09, 2017, 10:33:40 AM Hi Folks! Absolutely the same stuff I'm having now with my L3+ too. I had a well working L3+, then by mistake flashed it with D3 firmware (instead of different ASIC device... to fix the "x" issue solved in the 20th of November 2017 formware for D3). After that I immediately re-flashed back to the L3+ firmware but got what i got, Zero chips on each of the four hash-blades... I tried all the stuff including Micri SD image as did here and the same it didn't help. I also need this suggestion on which hex file to take and from where (the path) on the correctly working hash blade from another L3+. So I "ssh" the L3+ and should "scp" the file ?? to the same location on the malfunctioning L3+ (do that for all 4 blades) and then reboot. Cirrect? Which path to the file then guys? Please help. Thanks, Egor I had the same issue with my L3+. Mistakenly updated with D3 firmware. I was able to bring it back to life with PICkit 3 and hex file from another L3+. Many thanks guys!!! Happy to help man , please share the file to flash , i will edit 1st post with different solution later :) Title: Re: Issue new antminer l3+ Post by: cryptonitro on December 09, 2017, 10:48:58 AM /notlucky
Code: Dec 9 11:01:28 (none) local0.err cgminer: Miner compile time: Fri Aug 25 17:28:57 CST 2017 type: Antminer L3+ here the one i can flash , other no way https://img15.hostingpics.net/pics/67636520171209112922.jpg here the result with one fixed board and one more connected Code: Dec 9 10:45:39 (none) local0.err cgminer: Miner compile time: Fri Aug 25 17:28:57 CST 2017 type: Antminer L3+ edit : after reflash with one board seem to be not flashed , not succes for me even with fix2 kernel was done and it was mining at 30mhs (100mhz) like playboy333 but now board not recognize . a now stick to Code: Dec 9 12:05:25 (none) local0.notice cgminer[374]: i2c init ok re edit : after again and again , this time i got the 1 st board at up good ... but no way for toher , this make no sense. think i will use pickit at worst , will wait for next fix3 to try seem software version is not recognize everytime Title: Re: Issue new antminer l3+ Post by: omshree on December 10, 2017, 03:02:38 PM This is very strange. After flashing with PICkit all 6 badly flashed boards were working perfectly, it has nothing to do with the controller AFAIK.
One thing to notice, there are 2 different types of PIC chips, one has more memory, might the issue be in this direction? They are mixed in even one L+3 device, so random, Title: Re: Issue new antminer l3+ Post by: pitox on December 11, 2017, 10:10:54 AM Bliszz, are you goig to release a customm firmware for the L3+ like you did with for the D3?
It would really help to have per chain voltage/speed adjustment. I also have 2 L3+'s which are dead from flashing the D3 FW. I'm going to try your solution now. Title: Re: Issue new antminer l3+ Post by: playboy333 on December 11, 2017, 06:22:02 PM I am glad at least it helps a bit for you guys! I can imagine it's very annoying having a miner doing nothing... Still strange why one of the 4 boards is having a problem still for two of you now. If I find some more time for it I will dive into it Blissz and guys! Good news :D :D :D!!! I finally, managed to flash my hashboard using fix2 firmware. As you all remember I flashed only 3 out 4 hashboards from my l3+ that was bricked. In my case, playing with other chains 1,2,3 and changing connection cables out and about. I hope, my positive experimental experience will help and raise your mood!!! Thanks :), Blissz! I am looking forward your L3+ mod firmware!!!! :) :) :) :) http://hpics.li/ef8c32b Title: Re: Issue new antminer l3+ Post by: thantung3110 on December 11, 2017, 06:38:35 PM How is this everyone?
Title: Re: Issue new antminer l3+ Post by: tukker on December 12, 2017, 03:19:16 PM I had the same problem this week and was able to recover 3 boards of the 4 of my l3+
It takes a long time for some boards 2 i had to flash over 10 times before it shown CIP 0x3 thanks Blissz for the 4rth board i will wait for your new version Title: Re: Issue new antminer l3+ Post by: cryptonitro on December 13, 2017, 12:42:56 PM tried to extract hex of hte working board , with pickit3 with MPLAB IPE , the pic OF L3+ is PIC16F1705
But i cant read it :s Target device was not found (could not detect target voltage VDD). You must connect to a target device to use PICkit 3. 2017-12-13 13:41:38 +0100 - Read failed Title: Re: Issue new antminer l3+ Post by: cryptonitro on December 14, 2017, 10:03:25 AM I am glad at least it helps a bit for you guys! I can imagine it's very annoying having a miner doing nothing... Still strange why one of the 4 boards is having a problem still for two of you now. If I find some more time for it I will dive into it Blissz and guys! Good news :D :D :D!!! I finally, managed to flash my hashboard using fix2 firmware. As you all remember I flashed only 3 out 4 hashboards from my l3+ that was bricked. In my case, playing with other chains 1,2,3 and changing connection cables out and about. I hope, my positive experimental experience will help and raise your mood!!! Thanks :), Blissz! I am looking forward your L3+ mod firmware!!!! :) :) :) :) http://hpics.li/ef8c32b so it s flashing sometime when you have Blisssz: Chain not found 0 Blisssz: Chain not found 1 ? have only 2 working ... i try to flash again and again :'( Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: hellscreamer on December 15, 2017, 02:03:38 AM It's confirmed guys ! I have 4/4 working hashboard as usual . Just connect all hashboards to another working L3+ , and flash the stock firmware. ;D ------ Under Device Family of PICkit , what do you pick to export the right HEX ? I was able to flash the 4th board by hooking up to another hashboard in my other L3+ using stock firmware , and then reflash only the 4th board. But still stuck with 3/4 hashboard . I planned to swap the 4th board with a working board from other miner , will update soon if I can have 4/4 . PICkit is more likely to solve this Best regards Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on December 15, 2017, 12:05:11 PM It's confirmed guys ! I have 4/4 working hashboard as usual . Just connect all hashboards to another working L3+ , and flash the stock firmware. ;D ------ Under Device Family of PICkit , what do you pick to export the right HEX ? I was able to flash the 4th board by hooking up to another hashboard in my other L3+ using stock firmware , and then reflash only the 4th board. But still stuck with 3/4 hashboard . I planned to swap the 4th board with a working board from other miner , will update soon if I can have 4/4 . PICkit is more likely to solve this Best regards what you say make no sense , i change the controle board by a new one and try to flash firmware , hashboards was still down ... i have 2 working ont my l3+ and connect the 2 other and try flash stock firmware and they are not all working. Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: hellscreamer on December 15, 2017, 10:34:02 PM I used older firmware , you must leave one of the working hashboard and flash them together I guess
omshree , please share what Device Family did you pick when using the Pickit to flash the hex file , share a working window if possible. Antminer-L3+-201704271426-384M.tar.gz I posted the logs , maybe Blizz can help Quote [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 64768 pages, LIFO batch:15 [ 0.000000] AM335X ES1.0 (neon ) [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0933000 s9408 r8192 d15168 u32768 [ 0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc:
[ 0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] allocated 524288 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 255MB = 255MB total [ 0.000000] Memory: 240548k/240548k available, 21596k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB) [ 0.000000] .text : 0xc0008000 - 0xc0612cf0 (6188 kB) [ 0.000000] .init : 0xc0613000 - 0xc06554c0 ( 266 kB) [ 0.000000] .data : 0xc0656000 - 0xc06cc020 ( 473 kB) [ 0.000000] .bss : 0xc06cc020 - 0xc0725e3c ( 360 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000354] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968) [ 0.015443] pid_max: default: 32768 minimum: 301 [ 0.015674] Security Framework initialized [ 0.015770] Mount-cache hash table entries: 512 [ 0.024589] Initializing cgroup subsys cpuacct [ 0.024623] Initializing cgroup subsys memory [ 0.024687] Initializing cgroup subsys blkio [ 0.024821] CPU: Testing write buffer coherency: ok [ 0.025395] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.025473] Setting up static identity map for 0x8038c820 - 0x8038c86c [ 0.026801] Brought up 1 CPUs [ 0.026824] SMP: Total of 1 processors activated (545.07 BogoMIPS). [ 0.028123] devtmpfs: initialized [ 0.092506] pinctrl core: initialized pinctrl subsystem [ 0.092725] rstctl core: initialized rstctl subsystem [ 0.093217] regulator-dummy: no parameters [ 0.093787] NET: Registered protocol family 16 [ 0.094488] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.104160] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle [ 0.104344] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.105428] platform 49000000.edma: alias fck already exists [ 0.105462] platform 49000000.edma: alias fck already exists [ 0.105491] platform 49000000.edma: alias fck already exists [ 0.106633] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.106816] OMAP GPIO hardware version 0.1 [ 0.108223] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.109539] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.110852] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.111486] of_get_named_gpio_flags exited with status 52 [ 0.111515] gpio-rctrl rstctl.3: loaded OK [ 0.116627] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.119838] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.122015] cpsw.0: No hwaddr in dt. Using 90:70:65:33:30:66 from efuse [ 0.122048] cpsw.1: No hwaddr in dt. Using 90:70:65:33:30:68 from efuse [ 0.137597] bio: create slab <bio-0> at 0 [ 0.149731] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.149970] of_get_named_gpio_flags: can't parse gpios property [ 0.150262] vmmcsd_fixed: 3300 mV [ 0.153378] SCSI subsystem initialized [ 0.153825] usbcore: registered new interface driver usbfs [ 0.153939] usbcore: registered new interface driver hub [ 0.154268] usbcore: registered new device driver usb [ 0.156377] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz [ 0.156410] omap_i2c 4819c000.i2c: unable to select pin group [ 0.156604] media: Linux media interface: v0.10 [ 0.156701] Linux video capture interface: v2.00 [ 0.156819] pps_core: LinuxPPS API ver. 1 registered [ 0.156835] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.157554] Advanced Linux Sound Architecture Driver Initialized. [ 0.158746] Switching to clocksource gp_timer [ 0.176692] NET: Registered protocol family 2 [ 0.177690] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.177780] TCP bind hash table entries: 2048 (order: 3, 40960 bytes) [ 0.177870] TCP: Hash tables configured (established 2048 bind 2048) [ 0.177962] TCP: reno registered [ 0.177989] UDP hash table entries: 256 (order: 1, 12288 bytes) [ 0.178035] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) [ 0.178524] NET: Registered protocol family 1 [ 0.179110] RPC: Registered named UNIX socket transport module. [ 0.179132] RPC: Registered udp transport module. [ 0.179145] RPC: Registered tcp transport module. [ 0.179159] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.179545] Trying to unpack rootfs image as initramfs... [ 1.713015] Freeing initrd memory: 10368K [ 1.713761] CPU PMU: probing PMU on CPU 0 [ 1.713795] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 1.714331] omap2_mbox_probe: platform not supported [ 1.718229] VFS: Disk quotas dquot_6.5.2 [ 1.718465] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.719841] NFS: Registering the id_resolver key type [ 1.719934] Key type id_resolver registered [ 1.719952] Key type id_legacy registered [ 1.720017] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.720458] msgmni has been set to 490 [ 1.723256] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.723353] io scheduler noop registered [ 1.723372] io scheduler deadline registered [ 1.723434] io scheduler cfq registered (default) [ 1.727432] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.729905] omap_uart 44e09000.serial: did not get pins for uart0 error: -19 [ 1.730189] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0 [ 2.391010] console [ttyO0] enabled [ 2.395593] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1 [ 2.404261] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2 [ 2.412954] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4 [ 2.421558] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5 [ 2.430588] [drm] Initialized drm 1.1.0 20060810 [ 2.449213] brd: module loaded [ 2.459478] loop: module loaded [ 2.463716] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node [ 2.473710] nand_get_flash_type: 2c,da against 2c,da [ 2.479245] ONFI param page 0 valid [ 2.482914] ONFI flash detected [ 2.486233] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64 [ 2.498145] omap2-nand: detected x8 NAND flash [ 2.502811] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme [ 2.508392] omap2-nand: using custom ecc layout [ 2.513238] 10 ofpart partitions found on MTD device omap2-nand.0 [ 2.519640] Creating 10 MTD partitions on "omap2-nand.0": [ 2.525321] 0x000000000000-0x000000020000 : "spl" [ 2.532161] 0x000000020000-0x000000040000 : "spl_backup1" [ 2.539551] 0x000000040000-0x000000060000 : "spl_backup2" [ 2.546952] 0x000000060000-0x000000080000 : "spl_backup3" [ 2.554372] 0x000000080000-0x000000240000 : "u-boot" [ 2.562599] 0x000000240000-0x000000260000 : "bootenv" [ 2.569540] 0x000000260000-0x000000280000 : "fdt" [ 2.576154] 0x000000280000-0x000000780000 : "kernel" [ 2.587173] 0x000000800000-0x000001c00000 : "root" [ 2.610693] 0x000001c00000-0x000003000000 : "config" [ 2.634496] OneNAND driver initializing [ 2.640242] usbcore: registered new interface driver asix [ 2.646056] usbcore: registered new interface driver cdc_ether [ 2.652300] usbcore: registered new interface driver smsc95xx [ 2.658420] usbcore: registered new interface driver net1080 [ 2.664447] usbcore: registered new interface driver cdc_subset [ 2.670740] usbcore: registered new interface driver zaurus [ 2.676745] usbcore: registered new interface driver cdc_ncm [ 2.683466] usbcore: registered new interface driver cdc_acm [ 2.689424] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 2.697804] Initializing USB Mass Storage driver... [ 2.703047] usbcore: registered new interface driver usb-storage [ 2.709347] USB Mass Storage support registered. [ 2.714387] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 2.721101] musb-hdrc musb-hdrc.0.auto: pdev->id = 0 [ 2.726340] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.735112] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.735134] musb-hdrc: MHDRC RTL version 2.0 [ 2.735148] musb-hdrc: setup fifo_mode 4 [ 2.735176] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.735324] musb-hdrc musb-hdrc.0.auto: *** mode=3 [ 2.740368] musb-hdrc musb-hdrc.0.auto: *** power=250 [ 2.746384] musb-hdrc musb-hdrc.1.auto: pdev->id = 1 [ 2.751632] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.760423] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.760444] musb-hdrc: MHDRC RTL version 2.0 [ 2.760458] musb-hdrc: setup fifo_mode 4 [ 2.760480] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.760620] musb-hdrc musb-hdrc.1.auto: *** mode=1 [ 2.765667] musb-hdrc musb-hdrc.1.auto: *** power=250 [ 2.770982] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 2.777385] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 2.785628] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup [ 2.785733] usb usb1: default language 0x0409 [ 2.785830] usb usb1: udev 1, busnum 1, minor = 0 [ 2.785855] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.792978] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.800550] usb usb1: Product: MUSB HDRC host driver [ 2.805765] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd [ 2.811433] usb usb1: SerialNumber: musb-hdrc.1.auto [ 2.817433] usb usb1: usb_probe_device [ 2.817461] usb usb1: configuration #1 chosen from 1 choice [ 2.817525] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 2.817725] hub 1-0:1.0: usb_probe_interface [ 2.817746] hub 1-0:1.0: usb_probe_interface - got id [ 2.817773] hub 1-0:1.0: USB hub found [ 2.821772] hub 1-0:1.0: 1 port detected [ 2.825911] hub 1-0:1.0: standalone hub [ 2.825930] hub 1-0:1.0: individual port power switching [ 2.825948] hub 1-0:1.0: no over-current protection [ 2.825966] hub 1-0:1.0: Single TT [ 2.825987] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 2.826007] hub 1-0:1.0: power on to power good time: 10ms [ 2.826064] hub 1-0:1.0: local power source is good [ 2.826178] hub 1-0:1.0: enabling power on all ports [ 2.827265] mousedev: PS/2 mouse device common for all mice [ 2.835192] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 2.842942] i2c /dev entries driver [ 2.847944] pps_ldisc: PPS line discipline registered [ 2.853428] Driver for 1-wire Dallas network protocol. [ 2.860667] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 2.868238] cpuidle: using governor ladder [ 2.872567] cpuidle: using governor menu [ 2.877129] of_get_named_gpio_flags exited with status 6 [ 2.877150] of_get_named_gpio_flags: can't parse gpios property [ 2.877166] of_get_named_gpio_flags: can't parse gpios property [ 2.877203] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed [ 2.884440] omap_hsmmc mmc.4: Failed to get rstctl; not using any [ 2.891302] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 2.898509] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 2.905827] mmc.4 supply vmmc_aux not found, using dummy regulator [ 2.912829] omap_hsmmc mmc.4: pins are not configured from the driver [ 2.926530] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 2.946553] of_get_named_gpio_flags exited with status -517 [ 2.946618] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 2.954399] ledtrig-cpu: registered to indicate activity on CPUs [ 2.961177] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36 [ 2.968366] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 2.976460] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 2.982804] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 [ 2.989988] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 [ 3.002490] usbcore: registered new interface driver usbhid [ 3.008459] usbhid: USB HID core driver [ 3.015370] TCP: cubic registered [ 3.018897] Initializing XFRM netlink socket [ 3.023477] NET: Registered protocol family 17 [ 3.028287] NET: Registered protocol family 15 [ 3.033154] Key type dns_resolver registered [ 3.037833] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 3.045939] ThumbEE CPU extension supported. [ 3.050452] Registering SWP/SWPB emulation handler [ 3.056443] registered taskstats version 1 [ 3.063075] of_get_named_gpio_flags exited with status -517 [ 3.063222] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.119842] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 3.126253] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 3.140789] libphy: 4a101000.mdio: probed [ 3.145105] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 3.155350] Detected MACID = 90:70:65:33:30:66 [ 3.160026] cpsw 4a100000.ethernet: NAPI disabled [ 3.165421] of_get_named_gpio_flags exited with status -517 [ 3.165490] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.174222] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.183486] cpu0 supply cpu0 not found, using dummy regulator [ 3.190002] cpufreq_cpu0: failed to scale voltage up: -22 [ 3.195824] cpufreq_cpu0: failed to scale voltage up: -22 [ 3.208579] ALSA device list: [ 3.211815] No soundcards found. [ 3.216365] Freeing init memory: 264K [ 3.220413] Failed to execute /init [ 4.224902] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 5.521314] net eth0: initializing cpsw version 1.12 (0) [ 5.530322] net eth0: phy found : id is : 0x7c0f1 [ 5.535727] libphy: PHY 4a101000.mdio:01 not found [ 5.540937] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 9.677001] libphy: 4a101000.mdio:00 - Link is Up - 100/Full Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on December 16, 2017, 10:40:53 AM i think you didnt have the same error than people flash bad firmware ... this cant force flashing pics , or blissz fix have flash all your boards may be , i will try this firmware , but i m sure that wont change , but thanks for your try*
:) Title: Re: Issue new antminer l3+ Post by: cryptonitro on December 17, 2017, 02:14:17 PM This is very strange. After flashing with PICkit all 6 badly flashed boards were working perfectly, it has nothing to do with the controller AFAIK. One thing to notice, there are 2 different types of PIC chips, one has more memory, might the issue be in this direction? They are mixed in even one L+3 device, so random, seems some boards get logs like, and generaly flashing after a bit less than 5 minutes Code: Chain 0 PIC Version 0xcc and other Code: Chain 0 PIC Version 0x0 Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on December 18, 2017, 06:25:25 AM Had hexa files on 1st post for people want to manually flash
thanks to martin_fryc for sharing it Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: MoNTE48 on December 22, 2017, 01:46:55 AM I FIXED my board! Big thank!
Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: versuss on December 29, 2017, 11:12:23 AM Hello Friends,
I have the same problem - hashboard cannot be recognized from the Control IO Board. I read all posts here but can not understand where is this PIC and where is this EEPROM? On the hashboard I have 6 hole and I think that is for programming. Where can I get the pinout? The hashboard is L3+ and the controller with firmware for L3+. Please guys witch have experience with fixing of this problem on L3+ to write the procedure to resolve this problem. Best Regards Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on December 29, 2017, 11:38:15 AM Hello Friends, I have the same problem - hashboard cannot be recognized from the Control IO Board. I read all posts here but can not understand where is this PIC and where is this EEPROM? On the hashboard I have 6 hole and I think that is for programming. Where can I get the pinout? The hashboard is L3+ and the controller with firmware for L3+. Please guys witch have experience with fixing of this problem on L3+ to write the procedure to resolve this problem. Best Regards hi, did you try the firmware method ? manually write pic is delicate Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: versuss on December 29, 2017, 11:57:47 AM Yes I trying with FW method but without result. manual method is not problem for me I have pickit 3 and electronic knowledges but I need help and support...
Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: versuss on December 29, 2017, 01:47:24 PM Dear Friends,
I was connect my pickit3 to the hashboard as follow but I can not find programming software for pickit3 witch support PIC16F1704 Any ideas? Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: versuss on December 29, 2017, 03:38:12 PM Dear Friends,
i desolder programming and again solder the pic but without result. I am trying to load your fix firmware and with your firmware flashing the led green and nothing. When I load the original bitmain firmware the green led flashing than stop and start flashing the red led and after that the red led light on. Any ideas? Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: microtechies on December 29, 2017, 04:33:44 PM worked for me thanks
Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: versuss on December 29, 2017, 04:41:49 PM worked for me thanks Witch one work for you... FixFW or with programming the pic manually? Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: microtechies on December 29, 2017, 06:02:47 PM worked for me thanks Witch one work for you... FixFW or with programming the pic manually? The modded firmware and ruining one board at a time, then flashing official firmware and all 4 boards working. BTW I had this problem by accidentally installing the Blissz D3 Mod on my L3+ Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on January 05, 2018, 03:40:53 PM worked for me thanks Witch one work for you... FixFW or with programming the pic manually? The modded firmware and ruining one board at a time, then flashing official firmware and all 4 boards working. BTW I had this problem by accidentally installing the Blissz D3 Mod on my L3+ Very happy for you friend Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: aardvark20188 on January 07, 2018, 09:41:30 PM Hi All ,
I had the same problem , i erroneously flashed one of my antminer L+ miners with the wrong firmware , i dont know it was late , im sure i clicked on a link which was meant for a L3+ and not a D....however , i did flash it , and it was truly buggered ... tried reflashing original firmware, no good , tried the other firmware flash from this post, no good tried a support ticket with bitmain .....lol what did work was buying a pic programmer pulling the boards out and re-programming the the pic chips on the hash boards , one at time.. with the code from one of my working non flashed L+ miners , works perfectly now. Lessons learned , dont flash your L+ antminers with 3rd party incorrect miner firmware meant for dash miners... If anyone else is in the same predicament,anywhere north london, pm me , i do a program whilst you wait , for 10 a board .. .. Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on January 09, 2018, 01:36:09 PM Hi All , what is your batch I had the same problem , i erroneously flashed one of my antminer L+ miners with the wrong firmware , i dont know it was late , im sure i clicked on a link which was meant for a L3+ and not a D....however , i did flash it , and it was truly buggered ... tried reflashing original firmware, no good , tried the other firmware flash from this post, no good tried a support ticket with bitmain .....lol what did work was buying a pic programmer pulling the boards out and re-programming the the pic chips on the hash boards , one at time.. with the code from one of my working non flashed L+ miners , works perfectly now. Lessons learned , dont flash your L+ antminers with 3rd party incorrect miner firmware meant for dash miners... If anyone else is in the same predicament,anywhere north london, pm me , i do a program whilst you wait , for 10 a board .. .. whats are le kernel logs with this fix ? Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: aardvark20188 on January 10, 2018, 09:15:41 PM Hi there
I have the Dec 2017 batch L+ ,l the ones i've checked so far have the PIC16F1704 chip, but i believe there is also a batch with PIC16F1705 chips , however i have the hex for both I know don't why you would need kernel logs i just pulled the bricked hashing board out , connected it to the pickit3 tag and re-programmed it, popped it back in , and it worked , ive had no issues since ... Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: omshree on January 10, 2018, 09:28:37 PM Actually it does not matter which hex file you use, you can write the same to both types of chip
Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on January 13, 2018, 10:50:51 AM Hi there had a tutorial how to flash manually could be very nice from you for next people ... I have the Dec 2017 batch L+ ,l the ones i've checked so far have the PIC16F1704 chip, but i believe there is also a batch with PIC16F1705 chips , however i have the hex for both I know don't why you would need kernel logs i just pulled the bricked hashing board out , connected it to the pickit3 tag and re-programmed it, popped it back in , and it worked , ive had no issues since ... Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: m0nngis on January 29, 2018, 05:32:10 PM I have a D3 with the same problem - one of the boards show "0 ASICs" in the kernel log.
Any chance that someone (blissz?) could create a firmware fix for the D3 as well? I have neither the skills nor the tools to grab the PIC from one of the working boards and flashing it to the bricked one. Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: MarcusD on January 30, 2018, 12:12:00 PM Hi all,
Board 1,2,4 works perfect, Board 3 comes up and after few sec. the MH/s(RT) are 0. Can using this FIX ? Thanks Marcus Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on January 30, 2018, 10:16:51 PM Hi all, Board 1,2,4 works perfect, Board 3 comes up and after few sec. the MH/s(RT) are 0. Can using this FIX ? Thanks Marcus this do not seem an pic problem. if the board dont show 0 asic in logsd at start , this fix wont fix it Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: MarcusD on January 31, 2018, 09:13:03 AM Hi all, Board 1,2,4 works perfect, Board 3 comes up and after few sec. the MH/s(RT) are 0. Can using this FIX ? Thanks Marcus this do not seem an pic problem. if the board dont show 0 asic in logsd at start , this fix wont fix it Ok, any idea how to fix ? Thanks Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: stevebills on February 03, 2018, 12:09:41 AM Here's the issue you may have , hashboards are not recognized, anymore hello Sirhttps://img15.hostingpics.net/pics/396492403293Screenshot201711101152151.jpg /!\ please read carefuly /!\ ************************************************************** Firmware Flash ************************************************************** Here's a fix solution to rewite PIC's of L3+ after some of us flash bad firmware to their L3+. Many has recovered 3 boards , some all of it Thanks to Blissz for this fix (please do not pm him for this ) 1. Download File (re-up) Quote WARNING: Don't flash this to anything else as a bricked L3(+) caused by flashing a wrong firmware version, as this might harm a working L3(+). MEGA (https://mega.nz/#!8zwzGbRB!ImyUOtfpZbEo9E4DDnJv5M8ejXXVyh-2rjGsMfUYKQU) or 1fichier (https://1fichier.com/?rl6jg4941p) 2. Plug only 1 board from chain 0 (white cable on the left) as you can see under , you can plug upper hashboard 1st https://img15.hostingpics.net/pics/67636520171209112922.jpg 3. Go to system -> Upgrade -> "Flash new firmware image" choose the file downloaded to flash new firmware and click flash image wait for reboot. If kernel logs get this ... 0xcc , wait after you see it (5 minutes, to see again 0xcc or most of time 0x3 and then it will fix your board) other way try to connect an other boards and restart from "3" Quote Dec 17 14:09:30 (none) local0.warn cgminer: Started cgminer 4.9.0 Dec 17 14:09:30 (none) local0.notice cgminer[377]: detected at /sys/class/gpio/gpio51/value chain 0 Dec 17 14:09:30 (none) local0.notice cgminer[377]: detect total chain num 1 Dec 17 14:09:30 (none) local0.notice cgminer[377]: i2c init ok Dec 17 14:09:32 (none) local0.notice cgminer[377]: Chain 0 PIC Version 0xcc Dec 17 14:13:45 (none) local0.err cgminer[377]: Blisssz: Chain not found 1 Dec 17 14:13:45 (none) local0.err cgminer[377]: Blisssz: Chain not found 2 Dec 17 14:13:45 (none) local0.err cgminer[377]: Blisssz: Chain not found 3 Dec 17 14:13:51 (none) local0.notice cgminer[377]: Chain 0 PIC Version 0x3 [...] you will see some logs like this , PIC's is currently writing. Code: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] wait logs "miner start and switching pool" the board has been flashed with success. After fixing all or some of boards , you can finaly flash back bitmain l3+ original Firmware. (https://s3.cn-north-1.amazonaws.com.cn/shop-bitmain/download/Antminer-L3%2B-201708251737-384M.tar.gz) ************************************************************** Manually Flash ************************************************************** /!\ I will not assist with "how to" here cause i didnt experience it yet but if you have stuff (pickit3) and knowledge to manually flash chip of your miner here's the files ! warning ! have a look to the pic version you have (writed on the chip). there is PIC16F1704 or PIC16F1705 Here's the hexa files for each version MEGA PIC16F1704.hex (https://mega.nz/#!oEMByRqB!hm-s2VgoDe_jVEIRgECbHG0V2bLCujCAkOhXhJrswUc) PIC16F1705.hex (https://mega.nz/#!tQMCTZBS!n80UvNH-7fw1zQVjkBsRvIM_fA_0IBA9ikjVCMOFGK0) 1FICHIER PIC16F1704.hex (https://1fichier.com/?0am7he0kt8) PIC16F1705.hex (https://1fichier.com/?22xhc0iu36) Thanks to martin_fryc for sharing files, after succefully fix his L3+ by manually flashing PICs ************************************************************** I am looking on the board for the pic chip number and i cant se it please help me? thx steve Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: xefe on February 07, 2018, 01:34:19 AM Is there a version similar but for D3?
Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on February 09, 2018, 09:56:23 PM Here's the issue you may have , hashboards are not recognized, anymore hello Sirhttps://img15.hostingpics.net/pics/396492403293Screenshot201711101152151.jpg /!\ please read carefuly /!\ ************************************************************** Firmware Flash ************************************************************** Here's a fix solution to rewite PIC's of L3+ after some of us flash bad firmware to their L3+. Many has recovered 3 boards , some all of it Thanks to Blissz for this fix (please do not pm him for this ) 1. Download File (re-up) Quote WARNING: Don't flash this to anything else as a bricked L3(+) caused by flashing a wrong firmware version, as this might harm a working L3(+). MEGA (https://mega.nz/#!8zwzGbRB!ImyUOtfpZbEo9E4DDnJv5M8ejXXVyh-2rjGsMfUYKQU) or 1fichier (https://1fichier.com/?rl6jg4941p) 2. Plug only 1 board from chain 0 (white cable on the left) as you can see under , you can plug upper hashboard 1st https://img15.hostingpics.net/pics/67636520171209112922.jpg 3. Go to system -> Upgrade -> "Flash new firmware image" choose the file downloaded to flash new firmware and click flash image wait for reboot. If kernel logs get this ... 0xcc , wait after you see it (5 minutes, to see again 0xcc or most of time 0x3 and then it will fix your board) other way try to connect an other boards and restart from "3" Quote Dec 17 14:09:30 (none) local0.warn cgminer: Started cgminer 4.9.0 Dec 17 14:09:30 (none) local0.notice cgminer[377]: detected at /sys/class/gpio/gpio51/value chain 0 Dec 17 14:09:30 (none) local0.notice cgminer[377]: detect total chain num 1 Dec 17 14:09:30 (none) local0.notice cgminer[377]: i2c init ok Dec 17 14:09:32 (none) local0.notice cgminer[377]: Chain 0 PIC Version 0xcc Dec 17 14:13:45 (none) local0.err cgminer[377]: Blisssz: Chain not found 1 Dec 17 14:13:45 (none) local0.err cgminer[377]: Blisssz: Chain not found 2 Dec 17 14:13:45 (none) local0.err cgminer[377]: Blisssz: Chain not found 3 Dec 17 14:13:51 (none) local0.notice cgminer[377]: Chain 0 PIC Version 0x3 [...] you will see some logs like this , PIC's is currently writing. Code: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] wait logs "miner start and switching pool" the board has been flashed with success. After fixing all or some of boards , you can finaly flash back bitmain l3+ original Firmware. (https://s3.cn-north-1.amazonaws.com.cn/shop-bitmain/download/Antminer-L3%2B-201708251737-384M.tar.gz) ************************************************************** Manually Flash ************************************************************** /!\ I will not assist with "how to" here cause i didnt experience it yet but if you have stuff (pickit3) and knowledge to manually flash chip of your miner here's the files ! warning ! have a look to the pic version you have (writed on the chip). there is PIC16F1704 or PIC16F1705 Here's the hexa files for each version MEGA PIC16F1704.hex (https://mega.nz/#!oEMByRqB!hm-s2VgoDe_jVEIRgECbHG0V2bLCujCAkOhXhJrswUc) PIC16F1705.hex (https://mega.nz/#!tQMCTZBS!n80UvNH-7fw1zQVjkBsRvIM_fA_0IBA9ikjVCMOFGK0) 1FICHIER PIC16F1704.hex (https://1fichier.com/?0am7he0kt8) PIC16F1705.hex (https://1fichier.com/?22xhc0iu36) Thanks to martin_fryc for sharing files, after succefully fix his L3+ by manually flashing PICs ************************************************************** I am looking on the board for the pic chip number and i cant se it please help me? thx steve its directly write on the pic (find 5 linear wholes) the pic is just close to some people say the manual flash is working and not depending the pic you have , in fact flash any of 1704 or 1705 file. i didnt experience manual flash. and people did it , dont send back tutorial. hopefully someone send the files , thanks again to him :) Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on February 09, 2018, 09:57:32 PM Is there a version similar but for D3? i dont think so sorryTitle: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: FNT on February 26, 2018, 03:23:44 PM Hi guys,
I'd like to get the PIC hex code of the D3, as it's here for the L3+. Could anybody please send me the HEX file for PIC from a D3? or tell me where to find? Thanks and bye, FNT Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: nexoeon9 on May 19, 2018, 09:26:47 AM I was thinking to do the same for S9. 1 of my boards failed during trying to downclock my s9 with 550M firmware on autotune model. I even tried replacing the the PIC with a brand new one and reflashing firmware but I guess its just empty now. I'd be really great if someone could upload the PIC file from the S9. I already orderd the PICkit3. If not can someone tell me if I will be able to read from working board and write to faulty without desoldering the chips? If I manage to dump it I will upload. BTW. PIC firmware revision for S9 I'm looking for would be " fw version=0x03 " Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on May 22, 2018, 11:27:48 AM @nexoeon9 , you cant flash an other bitmain fw on s9 if you have auto ajust frequency 13.5th one
@chugelfish what do you mean by tweaked firmware , my download link are up ? or you mean the blissz one for l3+ replace original one? you say you have 2 l3+ break , but how do you broke them ? for D3 or s9 pics , sorry but i havent it. my chinese pickit3 seem to be dumb , i never flash manually success with it Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: nexoeon9 on May 22, 2018, 06:52:06 PM @cryptonitro I played around and managed to flash 550M, 600M and 650M onto my autotune S9 as I needed the fan control and potentially it to stay cooler. It worked but when I went from 650M back to 550M once board decided to give up on me... (it was before the april 2017 firmware update). But yes I know there are hardware differences between S9s and it could have bricked it completely.
Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: rascao on May 22, 2018, 07:06:11 PM for the D3 i use pickit 2 and i can read and write the pic but i have no difference on the d3 is broken i dont know what is wrong but is not the PIC
Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: concac on May 27, 2018, 12:11:57 PM My L3 + controller card is broken,
I used a replacement D3 controller card, After firmware update for D3 controller card with firmawre L3 +, I did not get the hash table of L3 + please help me how to use D3 controller card for L3 + thanks Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: WinMar on June 21, 2018, 04:56:45 PM I had the problem where all 4 of my hash boards got corrupted. I found the Blissz program and loaded it and all the hash boards started working. I am guessing that program writes the pic when I imaged at some point. Anyway it fully restored my miner. I could probably revert to bitmain code at this point and I am guessing it will still work.
My miner would start and connect maybe it would get 1 or 2 accepted shares and then stop. I tried reloading image and resetting nothing worked until I loaded blissz's program. Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: Stepan163 on August 25, 2018, 11:31:06 PM First and foremost I want to poblagodarite of ezabatzeko this firmware for their hard work!!! That's great!
Guys, help me!I installed the firmware on my L3+ as specified in the instructions. The result on the screen https://pp.userapi.com/c834304/v834304789/109dfc/Z9zAek5EuSg.jpg Kernel Log [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 64768 pages, LIFO batch:15 [ 0.000000] AM335X ES1.0 (neon ) [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0933000 s9408 r8192 d15168 u32768 [ 0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc:
[ 0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] allocated 524288 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 255MB = 255MB total [ 0.000000] Memory: 238816k/238816k available, 23328k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB) [ 0.000000] .text : 0xc0008000 - 0xc0612cf0 (6188 kB) [ 0.000000] .init : 0xc0613000 - 0xc06554c0 ( 266 kB) [ 0.000000] .data : 0xc0656000 - 0xc06cc020 ( 473 kB) [ 0.000000] .bss : 0xc06cc020 - 0xc0725e3c ( 360 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000358] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968) [ 0.015438] pid_max: default: 32768 minimum: 301 [ 0.015670] Security Framework initialized [ 0.015766] Mount-cache hash table entries: 512 [ 0.024598] Initializing cgroup subsys cpuacct [ 0.024629] Initializing cgroup subsys memory [ 0.024693] Initializing cgroup subsys blkio [ 0.024829] CPU: Testing write buffer coherency: ok [ 0.025396] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.025472] Setting up static identity map for 0x8038c820 - 0x8038c86c [ 0.026795] Brought up 1 CPUs [ 0.026819] SMP: Total of 1 processors activated (545.07 BogoMIPS). [ 0.028114] devtmpfs: initialized [ 0.092498] pinctrl core: initialized pinctrl subsystem [ 0.092718] rstctl core: initialized rstctl subsystem [ 0.093217] regulator-dummy: no parameters [ 0.093794] NET: Registered protocol family 16 [ 0.094502] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.104186] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle [ 0.104367] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.105446] platform 49000000.edma: alias fck already exists [ 0.105480] platform 49000000.edma: alias fck already exists [ 0.105509] platform 49000000.edma: alias fck already exists [ 0.106659] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.106841] OMAP GPIO hardware version 0.1 [ 0.108244] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.109566] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.110877] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.111507] of_get_named_gpio_flags exited with status 52 [ 0.111539] gpio-rctrl rstctl.3: loaded OK [ 0.116656] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.119867] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.122055] cpsw.0: No hwaddr in dt. Using 88:c2:55:41:f2:cf from efuse [ 0.122088] cpsw.1: No hwaddr in dt. Using 88:c2:55:41:f2:d1 from efuse [ 0.137659] bio: create slab <bio-0> at 0 [ 0.149782] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.150023] of_get_named_gpio_flags: can't parse gpios property [ 0.150311] vmmcsd_fixed: 3300 mV [ 0.153429] SCSI subsystem initialized [ 0.153884] usbcore: registered new interface driver usbfs [ 0.154000] usbcore: registered new interface driver hub [ 0.154328] usbcore: registered new device driver usb [ 0.156439] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz [ 0.156472] omap_i2c 4819c000.i2c: unable to select pin group [ 0.156668] media: Linux media interface: v0.10 [ 0.156762] Linux video capture interface: v2.00 [ 0.156879] pps_core: LinuxPPS API ver. 1 registered [ 0.156896] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.157612] Advanced Linux Sound Architecture Driver Initialized. [ 0.158806] Switching to clocksource gp_timer [ 0.176808] NET: Registered protocol family 2 [ 0.177799] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.177889] TCP bind hash table entries: 2048 (order: 3, 40960 bytes) [ 0.177979] TCP: Hash tables configured (established 2048 bind 2048) [ 0.178070] TCP: reno registered [ 0.178097] UDP hash table entries: 256 (order: 1, 12288 bytes) [ 0.178142] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) [ 0.178638] NET: Registered protocol family 1 [ 0.179225] RPC: Registered named UNIX socket transport module. [ 0.179246] RPC: Registered udp transport module. [ 0.179260] RPC: Registered tcp transport module. [ 0.179274] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.179663] Trying to unpack rootfs image as initramfs... [ 1.934320] Freeing initrd memory: 12100K [ 1.935006] CPU PMU: probing PMU on CPU 0 [ 1.935039] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 1.935570] omap2_mbox_probe: platform not supported [ 1.939461] VFS: Disk quotas dquot_6.5.2 [ 1.939698] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.941093] NFS: Registering the id_resolver key type [ 1.941195] Key type id_resolver registered [ 1.941212] Key type id_legacy registered [ 1.941279] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.941731] msgmni has been set to 490 [ 1.944620] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.944646] io scheduler noop registered [ 1.944662] io scheduler deadline registered [ 1.944719] io scheduler cfq registered (default) [ 1.948775] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.951217] omap_uart 44e09000.serial: did not get pins for uart0 error: -19 [ 1.951493] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0 [ 2.612386] console [ttyO0] enabled [ 2.616922] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1 [ 2.625589] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2 [ 2.634272] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4 [ 2.642887] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5 [ 2.651921] [drm] Initialized drm 1.1.0 20060810 [ 2.670566] brd: module loaded [ 2.680854] loop: module loaded [ 2.685081] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node [ 2.695060] nand_get_flash_type: 2c,da against 2c,da [ 2.700586] ONFI param page 0 valid [ 2.704258] ONFI flash detected [ 2.707578] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64 [ 2.719493] omap2-nand: detected x8 NAND flash [ 2.724159] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme [ 2.729742] omap2-nand: using custom ecc layout [ 2.734588] 10 ofpart partitions found on MTD device omap2-nand.0 [ 2.740983] Creating 10 MTD partitions on "omap2-nand.0": [ 2.746659] 0x000000000000-0x000000020000 : "spl" [ 2.753470] 0x000000020000-0x000000040000 : "spl_backup1" [ 2.760909] 0x000000040000-0x000000060000 : "spl_backup2" [ 2.768334] 0x000000060000-0x000000080000 : "spl_backup3" [ 2.775711] 0x000000080000-0x000000240000 : "u-boot" [ 2.783990] 0x000000240000-0x000000260000 : "bootenv" [ 2.790909] 0x000000260000-0x000000280000 : "fdt" [ 2.797492] 0x000000280000-0x000000780000 : "kernel" [ 2.808521] 0x000000800000-0x000001c00000 : "root" [ 2.832015] 0x000001c00000-0x000003000000 : "config" [ 2.855800] OneNAND driver initializing [ 2.861536] usbcore: registered new interface driver asix [ 2.867358] usbcore: registered new interface driver cdc_ether [ 2.873605] usbcore: registered new interface driver smsc95xx [ 2.879723] usbcore: registered new interface driver net1080 [ 2.885750] usbcore: registered new interface driver cdc_subset [ 2.892045] usbcore: registered new interface driver zaurus [ 2.898053] usbcore: registered new interface driver cdc_ncm [ 2.904777] usbcore: registered new interface driver cdc_acm [ 2.910735] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 2.919116] Initializing USB Mass Storage driver... [ 2.924356] usbcore: registered new interface driver usb-storage [ 2.930656] USB Mass Storage support registered. [ 2.935697] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 2.942436] musb-hdrc musb-hdrc.0.auto: pdev->id = 0 [ 2.947678] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.956450] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.956471] musb-hdrc: MHDRC RTL version 2.0 [ 2.956486] musb-hdrc: setup fifo_mode 4 [ 2.956514] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.956661] musb-hdrc musb-hdrc.0.auto: *** mode=3 [ 2.961707] musb-hdrc musb-hdrc.0.auto: *** power=250 [ 2.967769] musb-hdrc musb-hdrc.1.auto: pdev->id = 1 [ 2.973012] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.981784] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.981804] musb-hdrc: MHDRC RTL version 2.0 [ 2.981818] musb-hdrc: setup fifo_mode 4 [ 2.981840] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.981979] musb-hdrc musb-hdrc.1.auto: *** mode=1 [ 2.987037] musb-hdrc musb-hdrc.1.auto: *** power=250 [ 2.992347] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 2.998717] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 3.007192] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup [ 3.007300] usb usb1: default language 0x0409 [ 3.007358] usb usb1: udev 1, busnum 1, minor = 0 [ 3.007381] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.014524] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.022099] usb usb1: Product: MUSB HDRC host driver [ 3.027316] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd [ 3.032984] usb usb1: SerialNumber: musb-hdrc.1.auto [ 3.038973] usb usb1: usb_probe_device [ 3.039001] usb usb1: configuration #1 chosen from 1 choice [ 3.039065] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 3.039265] hub 1-0:1.0: usb_probe_interface [ 3.039289] hub 1-0:1.0: usb_probe_interface - got id [ 3.039316] hub 1-0:1.0: USB hub found [ 3.043325] hub 1-0:1.0: 1 port detected [ 3.047462] hub 1-0:1.0: standalone hub [ 3.047481] hub 1-0:1.0: individual port power switching [ 3.047500] hub 1-0:1.0: no over-current protection [ 3.047517] hub 1-0:1.0: Single TT [ 3.047539] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 3.047586] hub 1-0:1.0: power on to power good time: 10ms [ 3.047643] hub 1-0:1.0: local power source is good [ 3.047758] hub 1-0:1.0: enabling power on all ports [ 3.048803] mousedev: PS/2 mouse device common for all mice [ 3.056749] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 3.064515] i2c /dev entries driver [ 3.069596] pps_ldisc: PPS line discipline registered [ 3.075086] Driver for 1-wire Dallas network protocol. [ 3.082358] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 3.089933] cpuidle: using governor ladder [ 3.094263] cpuidle: using governor menu [ 3.098826] of_get_named_gpio_flags exited with status 6 [ 3.098846] of_get_named_gpio_flags: can't parse gpios property [ 3.098862] of_get_named_gpio_flags: can't parse gpios property [ 3.098900] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed [ 3.106138] omap_hsmmc mmc.4: Failed to get rstctl; not using any [ 3.112955] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 3.120182] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 3.127502] mmc.4 supply vmmc_aux not found, using dummy regulator [ 3.134442] omap_hsmmc mmc.4: pins are not configured from the driver [ 3.149251] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 3.169272] of_get_named_gpio_flags exited with status -517 [ 3.169341] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.177125] ledtrig-cpu: registered to indicate activity on CPUs [ 3.183904] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36 [ 3.191098] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 3.199214] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 3.205563] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 [ 3.212745] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 [ 3.224914] usbcore: registered new interface driver usbhid [ 3.230831] usbhid: USB HID core driver [ 3.237907] TCP: cubic registered [ 3.241479] Initializing XFRM netlink socket [ 3.246057] NET: Registered protocol family 17 [ 3.250837] NET: Registered protocol family 15 [ 3.255704] Key type dns_resolver registered [ 3.260338] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 3.268419] ThumbEE CPU extension supported. [ 3.272932] Registering SWP/SWPB emulation handler [ 3.278951] registered taskstats version 1 [ 3.285570] of_get_named_gpio_flags exited with status -517 [ 3.285644] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.342559] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 3.348972] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 3.363504] libphy: 4a101000.mdio: probed [ 3.367826] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 3.378067] Detected MACID = 88:c2:55:41:f2:cf [ 3.382748] cpsw 4a100000.ethernet: NAPI disabled [ 3.388139] of_get_named_gpio_flags exited with status -517 [ 3.388205] platform gpio-leds.7: Driver leds-gpio requests probe deferral [ 3.396941] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.406232] cpu0 supply cpu0 not found, using dummy regulator [ 3.412717] cpufreq_cpu0: failed to scale voltage up: -22 [ 3.418538] cpufreq_cpu0: failed to scale voltage up: -22 [ 3.431303] ALSA device list: [ 3.434534] No soundcards found. [ 3.439085] Freeing init memory: 264K [ 3.443140] Failed to execute /init [ 4.402757] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 5.765024] net eth0: initializing cpsw version 1.12 (0) [ 5.773966] net eth0: phy found : id is : 0x7c0f1 [ 5.779387] libphy: PHY 4a101000.mdio:01 not found [ 5.784582] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 8.848923] libphy: 4a101000.mdio:00 - Link is Up - 100/Full Aug 25 23:24:22 (none) local0.err cgminer: Miner compile time: Fri Aug 25 17:28:57 CST 2017 type: Antminer L3+ Aug 25 23:24:22 (none) local0.warn cgminer: Started cgminer 4.9.0 Aug 25 23:24:22 (none) local0.notice cgminer[374]: detected at /sys/class/gpio/gpio51/value chain 0 Aug 25 23:24:22 (none) local0.notice cgminer[374]: detected at /sys/class/gpio/gpio48/value chain 1 Aug 25 23:24:22 (none) local0.notice cgminer[374]: detect total chain num 2 Aug 25 23:24:22 (none) local0.notice cgminer[374]: i2c init ok Aug 25 23:24:24 (none) local0.notice cgminer[374]: Chain 0 PIC Version 0x3 Aug 25 23:24:24 (none) local0.notice cgminer[374]: Chain 1 PIC Version 0x3 Aug 25 23:24:24 (none) local0.err cgminer[374]: Blisssz: Chain not found 2 Aug 25 23:24:24 (none) local0.err cgminer[374]: Blisssz: Chain not found 3 Aug 25 23:24:34 (none) local0.notice cgminer[374]: in tty_init Aug 25 23:24:34 (none) local0.notice cgminer[374]: tty_init 0 Aug 25 23:24:34 (none) local0.notice cgminer[374]: Start A New Asic Response.Chain Id:[0] Aug 25 23:24:34 (none) local0.notice cgminer[374]: tty_init 1 Aug 25 23:24:34 (none) local0.notice cgminer[374]: Start A New Asic Response.Chain Id:[1] Aug 25 23:24:34 (none) local0.notice cgminer[374]: open device over Aug 25 23:24:35 (none) local0.notice cgminer[374]: send cmd to get chip address Aug 25 23:24:37 (none) local0.notice cgminer[374]: Chain 0 ASIC 8 !!! Aug 25 23:24:37 (none) local0.notice cgminer[374]: Chain 1 ASIC 42 !!! Aug 25 23:24:37 (none) local0.notice cgminer[374]: Need to recheck asic num !!! Aug 25 23:24:42 (none) local0.err cgminer: Miner compile time: Fri Aug 25 17:28:57 CST 2017 type: Antminer L3+ Aug 25 23:24:42 (none) local0.warn cgminer: Started cgminer 4.9.0 Aug 25 23:24:42 (none) local0.notice cgminer[444]: detected at /sys/class/gpio/gpio51/value chain 0 Aug 25 23:24:42 (none) local0.notice cgminer[444]: detected at /sys/class/gpio/gpio48/value chain 1 Aug 25 23:24:42 (none) local0.notice cgminer[444]: detect total chain num 2 Aug 25 23:24:42 (none) local0.notice cgminer[444]: i2c init ok Aug 25 23:24:44 (none) local0.notice cgminer[444]: Chain 0 PIC Version 0x3 Aug 25 23:24:44 (none) local0.notice cgminer[444]: Chain 1 PIC Version 0x3 Aug 25 23:24:44 (none) local0.err cgminer[444]: Blisssz: Chain not found 2 Aug 25 23:24:44 (none) local0.err cgminer[444]: Blisssz: Chain not found 3 Aug 25 23:24:54 (none) local0.notice cgminer[444]: in tty_init Aug 25 23:24:54 (none) local0.notice cgminer[444]: tty_init 0 Aug 25 23:24:54 (none) local0.notice cgminer[444]: Start A New Asic Response.Chain Id:[0] Aug 25 23:24:55 (none) local0.notice cgminer[444]: tty_init 1 Aug 25 23:24:55 (none) local0.notice cgminer[444]: Start A New Asic Response.Chain Id:[1] Aug 25 23:24:55 (none) local0.notice cgminer[444]: open device over Aug 25 23:24:55 (none) local0.notice cgminer[444]: send cmd to get chip address Aug 25 23:24:57 (none) local0.notice cgminer[444]: Chain 0 ASIC 8 !!! Aug 25 23:24:57 (none) local0.notice cgminer[444]: Chain 1 ASIC 42 !!! Aug 25 23:24:57 (none) local0.notice cgminer[444]: Need to recheck asic num !!! Aug 25 23:24:59 (none) local0.notice cgminer[444]: Chain 0 ASIC 8 !!! Aug 25 23:24:59 (none) local0.notice cgminer[444]: Chain 1 ASIC 42 !!! Aug 25 23:24:59 (none) local0.notice cgminer[444]: Need to recheck asic num !!! Aug 25 23:25:01 (none) local0.notice cgminer[444]: Chain 0 ASIC 8 !!! Aug 25 23:25:01 (none) local0.notice cgminer[444]: Chain 1 ASIC 42 !!! Aug 25 23:25:01 (none) local0.notice cgminer[444]: addrInterval = '6' Aug 25 23:25:01 (none) local0.notice cgminer[444]: software_set_address: chain 0 has 8 ASIC, and addrInterval is 6 Aug 25 23:25:01 (none) local0.notice cgminer[444]: Now Set
Aug 25 23:25:02 (none) local0.notice cgminer[444]: Now Set [1] Chain Address Aug 25 23:25:02 (none) local0.notice cgminer[444]: software_set_address: chain 2 has 0 ASIC, and addrInterval is 6 Aug 25 23:25:02 (none) local0.notice cgminer[444]: software_set_address: chain 3 has 0 ASIC, and addrInterval is 6 Aug 25 23:25:02 (none) local0.notice cgminer[444]: frequency = '100' Aug 25 23:25:02 (none) local0.notice cgminer[444]: dev.timeout = 151 Aug 25 23:25:02 (none) local0.notice cgminer[444]: opt_bitmain_L3_core_temp : 2 Aug 25 23:25:03 (none) local0.notice cgminer[444]: Dump IIC Data:[1][98][0][0]@ChainID:[0], Chip[C] Aug 25 23:25:03 (none) local0.notice cgminer[444]: Dump IIC Data:[1][98][0][0]@ChainID:[1], Chip[C] Aug 25 23:25:03 (none) local0.notice cgminer[444]: Dump IIC Data:[1][98][1][0]@ChainID:[0], Chip[C] Aug 25 23:25:03 (none) local0.notice cgminer[444]: Dump IIC Data:[1][98][1][0]@ChainID:[1], Chip[C] Aug 25 23:25:04 (none) local0.notice cgminer[444]: Dump IIC Data:[1][98][11][0]@ChainID:[0], Chip[C] Aug 25 23:25:04 (none) local0.notice cgminer[444]: Dump IIC Data:[1][98][11][0]@ChainID:[1], Chip[C] Aug 25 23:25:04 (none) local0.notice cgminer[444]: send cmd to open block Aug 25 23:25:06 (none) local0.err cgminer[444]: cgminer time error total_secs = 1535239506.809705 last_total_secs = 1.000000 Aug 25 23:25:06 (none) local0.warn cgminer[444]: Failed to resolve (?wrong URL) stratum+tcp://:(null) Aug 25 23:25:07 (none) local0.warn cgminer[444]: Pool 0 stratum+tcp://pool2pool.asuscomm.com:5521 alive, testing stability Aug 25 23:25:07 (none) local0.warn cgminer[444]: Switching to pool 0 stratum+tcp://pool2pool.asuscomm.com:5521 Aug 25 23:25:12 (none) local0.warn cgminer[444]: API running in IP access mode on port 4028 (15) Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: cryptonitro on August 31, 2018, 08:51:48 AM one board chips looks dead , other board may be work , it probably come from py connector
Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: Echo8002 on January 12, 2019, 10:19:28 AM Guys ,why the link for the repair firmware is not active?Can someone send me the file on PM ,please?Thanks in advance!
Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: ronald2010 on January 14, 2019, 06:09:03 PM someone has already experienced the L3 + stops no fan working and does not work anymore, the power is OK, I have tried an A3 controlboard but nothing works than also.
Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: guarrio on June 06, 2021, 07:30:29 AM I had the problem where all 4 of my hash boards got corrupted. I found the Blissz program and loaded it and all the hash boards started working. I am guessing that program writes the pic when I imaged at some point. Anyway it fully restored my miner. I could probably revert to bitmain code at this point and I am guessing it will still work. My miner would start and connect maybe it would get 1 or 2 accepted shares and then stop. I tried reloading image and resetting nothing worked until I loaded blissz's program. Do you mean the Blissz Firmware? did you just reinstall the Firmware and worked? Title: Re: [FIX] Issue antminer l3+ (boards not recognized, bad fw flash , etc) Post by: oscartheprofessor on June 08, 2021, 01:13:13 PM Here's the issue you may have , hashboards are not recognized, anymore https://img15.hostingpics.net/pics/396492403293Screenshot201711101152151.jpg /!\ please read carefuly /!\ ************************************************************** Firmware Flash ************************************************************** Here's a fix solution to rewite PIC's of L3+ after some of us flash bad firmware to their L3+. Many has recovered 3 boards , some all of it Thanks to Blissz for this fix (please do not pm him for this ) 1. Download File (re-up) Quote WARNING: Don't flash this to anything else as a bricked L3(+) caused by flashing a wrong firmware version, as this might harm a working L3(+). MEGA (https://mega.nz/#!8zwzGbRB!ImyUOtfpZbEo9E4DDnJv5M8ejXXVyh-2rjGsMfUYKQU) or 1fichier (https://1fichier.com/?rl6jg4941p) 2. Plug only 1 board from chain 0 (white cable on the left) as you can see under , you can plug upper hashboard 1st https://img15.hostingpics.net/pics/67636520171209112922.jpg 3. Go to system -> Upgrade -> "Flash new firmware image" choose the file downloaded to flash new firmware and click flash image wait for reboot. If kernel logs get this ... 0xcc , wait after you see it (5 minutes, to see again 0xcc or most of time 0x3 and then it will fix your board) other way try to connect an other boards and restart from "3" Quote Dec 17 14:09:30 (none) local0.warn cgminer: Started cgminer 4.9.0 Dec 17 14:09:30 (none) local0.notice cgminer[377]: detected at /sys/class/gpio/gpio51/value chain 0 Dec 17 14:09:30 (none) local0.notice cgminer[377]: detect total chain num 1 Dec 17 14:09:30 (none) local0.notice cgminer[377]: i2c init ok Dec 17 14:09:32 (none) local0.notice cgminer[377]: Chain 0 PIC Version 0xcc Dec 17 14:13:45 (none) local0.err cgminer[377]: Blisssz: Chain not found 1 Dec 17 14:13:45 (none) local0.err cgminer[377]: Blisssz: Chain not found 2 Dec 17 14:13:45 (none) local0.err cgminer[377]: Blisssz: Chain not found 3 Dec 17 14:13:51 (none) local0.notice cgminer[377]: Chain 0 PIC Version 0x3 [...] you will see some logs like this , PIC's is currently writing. Code: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9] wait logs "miner start and switching pool" the board has been flashed with success. After fixing all or some of boards , you can finaly flash back bitmain l3+ original Firmware. (https://s3.cn-north-1.amazonaws.com.cn/shop-bitmain/download/Antminer-L3%2B-201708251737-384M.tar.gz) ************************************************************** Manually Flash ************************************************************** /!\ I will not assist with "how to" here cause i didnt experience it yet but if you have stuff (pickit3) and knowledge to manually flash chip of your miner here's the files ! warning ! have a look to the pic version you have (writed on the chip). there is PIC16F1704 or PIC16F1705 Here's the hexa files for each version MEGA PIC16F1704.hex (https://mega.nz/#!oEMByRqB!hm-s2VgoDe_jVEIRgECbHG0V2bLCujCAkOhXhJrswUc) PIC16F1705.hex (https://mega.nz/#!tQMCTZBS!n80UvNH-7fw1zQVjkBsRvIM_fA_0IBA9ikjVCMOFGK0) 1FICHIER PIC16F1704.hex (https://1fichier.com/?0am7he0kt8) PIC16F1705.hex (https://1fichier.com/?22xhc0iu36) Thanks to martin_fryc for sharing files, after succefully fix his L3+ by manually flashing PICs ************************************************************** where are the images ?? and do i need to plug only 1 hash board to the circuit board ? and which version should i choose ..based on what ?? Title: Re: Issue new antminer l3+ Post by: oscartheprofessor on June 19, 2021, 09:08:00 PM No other solutions apart from sending it back, I am the one who discovered the manual flashing of the PIC controller, and I can confirm it works. can you please explain how to do that ? |
