Bitcoin Forum

Ask about gas gwei that use for send some token from myetherwallet to exchange.
Iam ever try send some token to market exchange.i try low gas gwei when i send my token to exchange..i try use 4 gwei.
But why when i use 4 gwei ,any token succesful send out but other token failed use 4 gwei,any info about low gas gwei,
what the factor that make token succesful send out or failed send out when we just use 4 gwei ,
Have you experience about it?
What your opinion?

I always use services that shows what recommended gas https://ethgasstation.info/. With the help of this site you can see what will happen with the increase of gas.

You don;t need to worry about the gwei or gas fee,
Simply visit ethgasstation for the present slow and fast gas fees for utilizations and also the easies one to use as well

Don't waste away your etherum so cheaply, remember to use ethgasstation always to guide you.
Ensure to verify the address you are sending to twice, and avoid sending to a smart contract.

Use the best gas and the highest gwei at a very cheap rate.

Just remember go to ethgasstation or etherscan gastracker check the safe Gas Price before send out token from mew, most of the time eth transaction fees is cheap, your transaction will become success if use the safe gas price, if sometimes failed then try to increase gas limit

every time
gas can incrased or decreased every transaction
for example
on block 1,4 GWEI still normal for paying miner to confrim ur transaction,
but on block 2,4 GWEI is not recomended, because high traffic, so to make ur transaction succesfully, u need to paying more.
for checking u can see on ethgasstation or etherscan also have menu for GAS

I always put the most minimal gas if I'm not in a hurry. if I  need to send my ETH quickly, for example, to participate in good ICO, then I put more gas

Please check out https://etherscan.io/gastracker before you make a transaction. Because the gas price is changing every time. I personally believe 4 gwei is too low to send ERC20 token transactions. Yes, sometimes it works. But not every time. It has a chance to fail your transactions.

2 important things need to remember when you send the token. Gas limit and Gas price.

1. Always set high Gas limit. If you do not sure how many is enough, you can set 100K - 150K.

2. There are 2 choices. Hurry: 10-15 Gwei. Have alot freetime: 3-5 Gwei.

And it seems that I have not failed to send any token with my solution.

If you use a lower gwei you normally need to set a higher gas limit or else your transaction might not go through. Very rarely will it use the full gas limit but the transaction won't be accepted otherwise because it's based on an average length for the transactions to be processed.

I use this service https://ethgasstation.info/ to find out which gwei is now for quick transaction, usualy I set gwei from item "gas price std" and transaction takes a few minutes but if you are ready to wait for 10-60 minutes you can use "Gas Price SafeLow ".

I don't think the tokens themselves matter. Maybe, you were sending on different time and in one of those times, it was a peak hour and the other one is not. I'm also using 4gwei on most of my token transfer, fortunately, they were all successful.

First of all, the recommended gas to send any ERC20/eth token is 8gwei, but it also mainly affected by the ETH network. When the network is busy filled with so many transaction the price of ethereum gas to send your token will be increased. To make sure your transaction is sent successfully, refer to http://ethgasstation.info to check the currently recommended gas. On the other hand, if you use wallet such as myetherwallet, usually their default gas is already meet the currently recommended gas.

myetherwaleet is one of the best wallets right now so i think if you have any problej with them just let them know

thatnk you verh much for such a good answer an di hope that you will believe in myetherwallet nusg like i do

Great example. I think it is not necessary to calculate to share. I often use 10 Gwei and everything works fine. It all depends on your needs.

If its unsuccessful then you have to increase your fee.
That's how you should make it successful, sometimes they aren't the same.
Fees such as gwei's are increasing depending on the network.

myetherwallet is one of them best right now ad i have heard they have a grsat support team so you can ask them what they think about it

myetherwallet will never let down its users so i think tt the only good decision here is let them know about the mistake

I think you are using less gwei because there was also some congestion in the eth network from past few days so may be you need to increase the gwei amount, i will suggest to set gwei over 10 in situation of network congestion.

No need to adjust the gwei because the mew is automatically set the gas price. Low gas means you set the gwei to low and you need to set the gas high in order to process your request.

I haven't experienced it, but I've heard about gas 4 gwei, many people say the gas is lower and the speed of delivery is also very amazing, I know a little if there is one token that can't use it

Same here. I always check ethgastation before sending any eth or tokens. You could be setting it too low and wait several hours before miners pickup your transaction.

It really depends how busy the network is, you can try to use ethgasstation.info to gauge the right amount to set your GWEI at, however, I have sometimes found this to be inaccurate and had to choose a GWEI setting higher than the recommended just to get it to work.

Take care with your gas limits also as sending ERC-20 tokens requires more than just sending ETH they are generally set automatically for you but occasionally you need to increase that also especially if you find the tx running out of gas.

right. I also experienced this before when I wanted to send a token from myetherwallet to exchange it when I used 4 gwei failed. but after I submitted to the rules it turned out that gwei could change at any time. therefore before we send the token from myetherwallet, we need to check the gwei first so that the delivery of the token does not fail.

I often use 4Gwei gas for transactions, for example, yesterday I did an IZX token send out transaction using 4Gwei and it was successful but when I sent the DARICO token, I used the same gas but there was a gas notification that was very lowaffect the cost of gas used.