Title: Issue with too many shares and disconnect when dual mining with CLAYMORE v12 Post by: mizeria on February 10, 2019, 10:24:00 PM here is what I have in start.bat
EthDcrMiner64.exe -epool europe.ethash-hub.miningpoolhub.com:20535 -ewal mizeria.mizeria -eworker mizeria.mizeria -epsw x -esm 1 -dpool stratum+tcp://coinotron.com:3350 -dwal mizeria.001 -esm 2 -dpsw x -dcoin pasc -allpools 1 and here is the log ╔════════════════════════════════════════════════════════════════╗ ║ Claymore's Dual GPU Miner - v12.0 ║ ║ ETH + DCR/SIA/LBC/PASC/BLAKE2S/KECCAK ║ ╚════════════════════════════════════════════════════════════════╝ ETH: 1 pool is specified Main Ethereum pool is europe.ethash-hub.miningpoolhub.com:20535 PASC: 1 pool is specified Main Pascal pool is coinotron.com:3350 At least 16 GB of Virtual Memory is required for multi-GPU systems Make sure you defined GPU_MAX_ALLOC_PERCENT 100 Be careful with overclocking, use default clocks for first tests Press "s" for current statistics, "0".."9" to turn on/off cards, "r" to reload pools, "e" or "d" to select current pool, "x" to select GPU, "z" to find best -dcri values Press "y" to set Compute Mode and disable CrossFire in AMD drivers for all cards OpenCL initializing... AMD Cards available: 2 GPU #0: gfx901 (Radeon RX Vega), 8176 MB available, 64 compute units (pci bus 11:0:0) GPU #0 recognized as Vega GPU #1: Ellesmere (Radeon RX 580 Series), 8192 MB available, 36 compute units (pci bus 65:0:0) GPU #1 recognized as Radeon RX 480/580 POOL/SOLO version GPU #0: algorithm ASM 1 GPU #1: algorithm ASM 1 No NVIDIA CUDA GPUs detected. Total cards: 2 ETH: Stratum - connecting to 'europe.ethash-hub.miningpoolhub.com' <18.197.166.72> port 20535 (unsecure) ETH: Stratum - Connected (europe.ethash-hub.miningpoolhub.com:20535) (unsecure) DUAL MINING MODE ENABLED: ETHEREUM+PASCAL PASC: Stratum - connecting to 'coinotron.com' <178.217.186.125> port 3350 (unsecure) ETH: miner-proxy stratum mode "-allpools" option is set, default pools can be used for devfee, check "Readme" file for details. Watchdog enabled Remote management (READ-ONLY MODE) is enabled on port 3333 PASC: Stratum - Connected (coinotron.com:3350) (unsecure) Setting DAG epoch #240... PASC: Authorized PASC: Share rejected! ETH: Authorized ETH: 02/11/19-00:19:43 - New job from europe.ethash-hub.miningpoolhub.com:20535 ETH - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00 ETH: GPU0 0.000 Mh/s, GPU1 0.000 Mh/s PASC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 1 PASC: GPU0 0.000 Mh/s, GPU1 0.000 Mh/s Setting DAG epoch #240 for GPU1 Setting DAG epoch #240 for GPU0 Create GPU buffer for GPU1 Create GPU buffer for GPU0 GPU0 DAG creation time - 2509 ms Setting DAG epoch #240 for GPU0 done PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: Share rejected (0 ms)! PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: Share rejected (78 ms)! PASC: Share rejected (187 ms)! PASC: Share rejected (250 ms)! PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: Share rejected (78 ms)! PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: Share rejected (0 ms)! PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: 02/11/19-00:19:47 - SHARE FOUND - (GPU 0) PASC: Share rejected (78 ms)! PASC: Share rejected (109 ms)! PASC: Share rejected (109 ms)! PASC: Share rejected (109 ms)! PASC: Share rejected (109 ms)! PASC: Share rejected (109 ms)! PASC: Share rejected (109 ms)! PASC: Share rejected (109 ms)! PASC: Too many rejects from pool, disconnect... PASC: - connection in 20 sec... The Eth mining is ok but the pascal mining shares rejected is a problem. I have tried also another 2 pools but the same thing with rejected shares. When doing Eth only solo mining everything is perfect. Thanks! Title: Re: Issue with too many shares and disconnect when dual mining with CLAYMORE v12 Post by: mikeywith on February 11, 2019, 12:29:10 AM did you try to adjust the intensity ? it's either the intensity or the overclocking is too much. these are the most likely scenarios.
Title: Re: Issue with too many shares and disconnect when dual mining with CLAYMORE v12 Post by: mizeria on February 11, 2019, 09:04:17 AM did you try to adjust the intensity ? it's either the intensity or the overclocking is too much. these are the most likely scenarios. What you mean by intensity? What I have to adjust? Also I will try to bypass the overclocking to see what I get and let you know. Do you think the start.bat settings are correct? Thank you! Title: Re: Issue with too many shares and disconnect when dual mining with CLAYMORE v12 Post by: mikeywith on February 11, 2019, 02:35:25 PM What you mean by intensity? What I have to adjust? Also I will try to bypass the overclocking to see what I get and let you know. Do you think the start.bat settings are correct? Thank you! you have to reduce or increase it until the issue disappears, at the end of the bat file you need to add this Code: -dcri 45 while running use the + and - on your keyboard to adjust it, once you get the number you want, save it in the bat file. post the bat file here so i can tell you if there is anything wrong. Title: Re: Issue with too many shares and disconnect when dual mining with CLAYMORE v12 Post by: mizeria on February 11, 2019, 02:57:41 PM What you mean by intensity? What I have to adjust? Also I will try to bypass the overclocking to see what I get and let you know. Do you think the start.bat settings are correct? Thank you! you have to reduce or increase it until the issue disappears, at the end of the bat file you need to add this Code: -dcri 45 while running use the + and - on your keyboard to adjust it, once you get the number you want, save it in the bat file. post the bat file here so i can tell you if there is anything wrong. here is what I have in start.bat EthDcrMiner64.exe -epool europe.ethash-hub.miningpoolhub.com:20535 -ewal mizeria.mizeria -eworker mizeria.mizeria -epsw x -esm 1 -dpool stratum+tcp://coinotron.com:3350 -dwal mizeria.001 -esm 2 -dpsw x -dcoin pasc -allpools 1 Title: Re: Issue with too many shares and disconnect when dual mining with CLAYMORE v12 Post by: mikeywith on February 11, 2019, 04:14:22 PM What you mean by intensity? What I have to adjust? Also I will try to bypass the overclocking to see what I get and let you know. Do you think the start.bat settings are correct? Thank you! you have to reduce or increase it until the issue disappears, at the end of the bat file you need to add this Code: -dcri 45 while running use the + and - on your keyboard to adjust it, once you get the number you want, save it in the bat file. post the bat file here so i can tell you if there is anything wrong. here is what I have in start.bat EthDcrMiner64.exe -epool europe.ethash-hub.miningpoolhub.com:20535 -ewal mizeria.mizeria -eworker mizeria.mizeria -epsw x -esm 1 -dpool stratum+tcp://coinotron.com:3350 -dwal mizeria.001 -esm 2 -dpsw x -dcoin pasc -allpools 1 save your current setting somewhere, and replace them with this Code: EthDcrMiner64.exe -epool europe.ethash-hub.miningpoolhub.com:20535 -ewal mizeria.mizeria -eworker mizeria.mizeria -epsw x -dcri 34 -dcoin pasc -dpool stratum+tcp://coinotron.com:3350 -dwal mizeria.001 -esm 2 -dpsw x try different -dcri values until you find the one that works best, for many gpus it's 45 that does the trick, but you really need to try different values , keep track on ETH hashrate as it will change based on the -dcri value, so find the number the suits you best. if the problem is still there, then you need to reduce your gpu freq, i would also try another coin. Title: Re: Issue with too many shares and disconnect when dual mining with CLAYMORE v12 Post by: mizeria on February 11, 2019, 04:19:18 PM What you mean by intensity? What I have to adjust? Also I will try to bypass the overclocking to see what I get and let you know. Do you think the start.bat settings are correct? Thank you! you have to reduce or increase it until the issue disappears, at the end of the bat file you need to add this Code: -dcri 45 while running use the + and - on your keyboard to adjust it, once you get the number you want, save it in the bat file. post the bat file here so i can tell you if there is anything wrong. here is what I have in start.bat EthDcrMiner64.exe -epool europe.ethash-hub.miningpoolhub.com:20535 -ewal mizeria.mizeria -eworker mizeria.mizeria -epsw x -esm 1 -dpool stratum+tcp://coinotron.com:3350 -dwal mizeria.001 -esm 2 -dpsw x -dcoin pasc -allpools 1 save your current setting somewhere, and replace them with this Code: EthDcrMiner64.exe -epool europe.ethash-hub.miningpoolhub.com:20535 -ewal mizeria.mizeria -eworker mizeria.mizeria -epsw x -dcri 34 -dcoin pasc -dpool stratum+tcp://coinotron.com:3350 -dwal mizeria.001 -esm 2 -dpsw x try different -dcri values until you find the one that works best, for many gpus it's 45 that does the trick, but you really need to try different values , keep track on ETH hashrate as it will change based on the -dcri value, so find the number the suits you best. if the problem is still there, then you need to reduce your gpu freq, i would also try another coin. I will try and let you know. Thank you very much! Title: Re: Issue with too many shares and disconnect when dual mining with CLAYMORE v12 Post by: fanatic26_ on February 11, 2019, 05:29:44 PM Why has noone mentioned this is not the place to be posting this? Please post in the proper altcoin section.
p.s. dual mining is basically dead at this point Title: Re: Issue with too many shares and disconnect when dual mining with CLAYMORE v12 Post by: styleshifter on February 12, 2019, 12:39:15 PM You could try another miner like Phoenix Miner, too.
It has only 0.65% dev fee and supports most of Claymore's command-line options and configuration files. Check my overview page for the latest mining software: https://latest-miner.firebaseapp.com/ (https://latest-miner.firebaseapp.com/) Title: Re: Issue with too many shares and disconnect when dual mining with CLAYMORE v12 Post by: sxemini on February 12, 2019, 01:15:19 PM LOL you know that pascal coin has forked to the algo randomhash in november, so no mining possible with claymore.
You can dual mine pascallite Why you don´t read the help from cointron? ::) https://www.coinotron.com/app?action=help Next time check algo and such easy things, before you start mining. @styleshifter don´t spam this forum with such stupid answers and webpages. If someone need a miner, load it from github or from the bitcointalk thread. And phönixminer only support dualmining ethash and blake2s and not pascal. |