Title: Avalon 921 blue light but dont hash Post by: Bloodstorm88 on January 15, 2021, 01:23:37 PM Hello, I have a problem with my Avalon 921, here my CGminer API log.... The light is blue on my avalon, auc3 are green, everything look fines...but no hash.
Code: [Firmware Version] => Avalon Firmware for avalon9 - 20190301 Title: Re: Avalon 921 blue light but dont hash Post by: mikeywith on January 17, 2021, 04:25:18 AM MW0[0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0] MW1[0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0] MW2[0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0] MW3[0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0] The API log is saying that all 4 hash boards are bad, but what are the chances? there is probably something else that's causing the problem, did you buy the miner recently? was it working? this information can be really handy in troubleshooting, you should also post your issue in this topic (https://bitcointalk.org/index.php?topic=3224256.0), HagssFIN is an expert in Avalon gears. Title: Re: Avalon 921 blue light but dont hash Post by: NotFuzzyWarm on January 18, 2021, 02:03:51 PM Are the controller and miner firmware both the same version? Both have to be the same or Avalons will not run.
Also missing from the log is any information about the AUC3 dongle. Right after the board info (MW0, MW1, MW2, MW3) should be this: Code: CRC[0 1 0 1],MM Count=1,Smart Speed=1,Connecter=AUC,AUC VER=AUC-20151208,AUC I2C Speed=400000,AUC I2C XDelay=19200,AUC Sensor=15548,AUC Temperature=27.96,Connection Overloaded=false,Voltage Level Offset=0,Nonce Mask=24,USB Pipe=0,USB Delay=r0 0.000000 w0 0.000000,USB tmo=0 0|STATS=1,ID=POOL0,Elapsed=3667879,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=8190.00000000,Min Diff=8190.00000000,Max Diff=8190.00000000,Min Diff Count=4635064,Max Diff Count=4635064,Times Sent=920042,Bytes Sent=130533721,Times Recv=1044781,Bytes Recv=199049292,Net Bytes Sent=130533721,Net Bytes Recv=199049292|STATS=2,ID=POOL1,Elapsed=3667879,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=0.00000000,Min Diff=0.00000000,Max Diff=0.00000000,Min Diff Count=0,Max Diff Count=0,Times Sent=2,Bytes Sent=153,Times Recv=5,Bytes Recv=1476,Net Bytes Sent=153,Net Bytes Recv=1476|STATS=3,ID=POOL2,Elapsed=3667879,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=0.00000000,Min Diff=0.00000000,Max Diff=0.00000000,Min Diff Count=0,Max Diff Count=0,Times Sent=2,Bytes Sent=153,Times Recv=6,Bytes Recv=2674,Net Bytes Sent=153,Net Bytes Recv=2674|' edit: Should also add to be sure that you are using a USB data cable between the RasPi & AUC3 vs a charging cable. Charging cables often only have 2 wires in them and will not support data xfrs. Title: Re: Avalon 921 blue light but dont hash Post by: HagssFIN on January 18, 2021, 05:15:30 PM Is it the same with any pool?
Title: Re: Avalon 921 blue light but dont hash Post by: Steamtyme on January 18, 2021, 05:32:43 PM How long did you wait after turning on the gear to check for an error? The Log readout is showing 55 seconds for relapsed time. If this is the first time you've fired up the gear you should give it a couple minutes to try and ramp up fully to be sure there is a problem in the first place. If it does start hashing, wait a half hour or so to get an idea of it's Total AVG. to decide if there might be an issue.
Answers to everybody's questions will help in sorting this out. |