|
Title: Antminer L3+ can’t find asic boards Post by: Rogga31 on May 07, 2021, 06:10:57 PM Hi I need some expert help on this. My Antminer just shows 0 on all 4 asic boards. Is it the status board that is faulty or is there some other issues? From Kernel log: May 7 17:50:46 (none) local0.notice cgminer[381]: Start A New Asic Response.Chain Id:[1] May 7 17:50:46 (none) local0.notice cgminer[381]: tty_init 2 May 7 17:50:46 (none) local0.notice cgminer[381]: Start A New Asic Response.Chain Id:[2] May 7 17:50:46 (none) local0.notice cgminer[381]: tty_init 3 May 7 17:50:46 (none) local0.notice cgminer[381]: Start A New Asic Response.Chain Id:[3] May 7 17:50:46 (none) local0.notice cgminer[381]: open device over May 7 17:50:46 (none) local0.notice cgminer[381]: send cmd to get chip address May 7 17:50:48 (none) local0.notice cgminer[381]: Chain 0 ASIC 0 !!! May 7 17:50:48 (none) local0.notice cgminer[381]: Chain 1 ASIC 0 !!! May 7 17:50:48 (none) local0.notice cgminer[381]: Chain 2 ASIC 0 !!! May 7 17:50:48 (none) local0.notice cgminer[381]: Chain 3 ASIC 0 !!! May 7 17:50:48 (none) local0.notice cgminer[381]: Need to recheck asic num !!! May 7 17:50:49 (none) local0.err cgminer: Miner compile time: Sun Jan 14 00:00:57 CST 2018 type: Antminer L3+ Blissz v1.02 May 7 17:50:49 (none) local0.warn cgminer: Started cgminer 4.10.0 Appreciate any help on this! Title: Re: Antminer L3+ can’t find asic boards Post by: philipma1957 on May 07, 2021, 06:16:28 PM you have installed bliss firmware so I do not know if you have a corrupted version of it.
Did it ever work? Did it work with bitmain firmware? Title: Re: Antminer L3+ can’t find asic boards Post by: Rogga31 on May 07, 2021, 06:59:22 PM Hi
It worked on original firmware and also on Bliss firmware ( I also have the same Bliss firmware on three other L3 working fine). But when I moved the machine it stopped working. Title: Re: Antminer L3+ can’t find asic boards Post by: philipma1957 on May 07, 2021, 08:26:50 PM Hi It worked on original firmware and also on Bliss firmware ( I also have the same Bliss firmware on three other L3 working fine). But when I moved the machine it stopped working. And did you move it in the same home? or to a different home. It may not be compatible with the new internet. If it is on the same internet we can do some other troubleshooting Title: Re: Antminer L3+ can’t find asic boards Post by: Rogga31 on May 07, 2021, 09:38:32 PM Moved from cellar to garage. Still on same network. And I also have three other working L3 on that network.
Title: Re: Antminer L3+ can’t find asic boards Post by: Philipma1957cellphone on May 07, 2021, 11:33:30 PM Moved from cellar to garage. Still on same network. And I also have three other working L3 on that network. [/quote At party and a bit drunk. Let me get.back to you in the morning. Title: Re: Antminer L3+ can’t find asic boards Post by: Rogga31 on May 08, 2021, 07:09:57 AM Sounds fun with party :).
Thanks for looking into this, appreciated! Title: Re: Antminer L3+ can’t find asic boards Post by: philipma1957 on May 08, 2021, 01:43:01 PM Sounds fun with party :). Thanks for looking into this, appreciated! All sober. Okay so assuming you simply detached the l3+ from its eth cable and walked it into another room. You then plugged it into a new power outlet and are using an eth cable in the new spot. Assuming the 3 good units in different room are all working. Lets try detaching 1 good unit. leave it sit just out of the way. bring the dead unit to the spot you detached a working unit. plug the dead unit in boot and let us know if it works. if it does not work put it aside. reattach the good unit and boot it should work. If all of the above is true then you know the problem is within the dead miner. Title: Re: Antminer L3+ can’t find asic boards Post by: Rogga31 on May 08, 2021, 03:57:37 PM I hope that you had a good time!
Took the faulty machine to the spot with the working machines. Unplugged one of the working one. Use that eth cable and also the power supply. Still not working. Attached the eth cable and psu to the working one and booted up that and it works fine. So I think that we can assume that there is something that is not working as it should in the faulty machine. Title: Re: Antminer L3+ can’t find asic boards Post by: philipma1957 on May 08, 2021, 06:25:53 PM I hope that you had a good time! Took the faulty machine to the spot with the working machines. Unplugged one of the working one. Use that eth cable and also the power supply. Still not working. Attached the eth cable and psu to the working one and booted up that and it works fine. So I think that we can assume that there is something that is not working as it should in the faulty machine. The control board sometimes dies. I have 2 good hash boards in the house and three bad controllers. It is more likely the controller died and not the 4 hash boards. Try a few resets then flashing the controller with the firmware. Oh BTW the party/dinner was fun Title: Re: Antminer L3+ can’t find asic boards Post by: Rogga31 on May 08, 2021, 08:37:53 PM Thanks, I will give it a go and if it doesn’t work I will change status board.
|