|
Title: Hardware/Software Help Needed! Post by: SilverWWW on July 21, 2021, 01:32:17 AM Hey yo,
Currently in the process of setting up a new rig and am having some trouble with GPU detection after POST. For context, I'm using an ASUS B250 and it shows me a screen of which cards are working and which aren't right before launching BIOS. Anyways, on my very first POST, I had one card in and it detected fine - showed up green and everything. Then, for some reason, each time I relaunch BIOS, the slot the card is plugged into always comes up with an error. I went a tweaked around with the BIOS setting (detailed description below), but no luck. Was wondering if anyone had any ideas. Thanks! BIOS setting changes: - Changed primary display to CPU graphics from PCI-E - Changed both PCIe and PCIEX16_1 speeds from Gen1 to Auto - Disabled SATA ports 2-4 (not in use) - Enabled Power on by PCI-E - Disabled HD Audio Controller No big changes really, as you can see. Also, I've tried detecting the card on both Gen1 and 2, but no luck. Ideas? Title: Re: Hardware/Software Help Needed! Post by: anu1908 on July 21, 2021, 05:48:31 AM have you checked whether your card is ok? what about the power, is it sufficient to power up all of your cards? as one last resort, maybe try to clean the slot itself just in case there's some dust there.
Title: Re: Hardware/Software Help Needed! Post by: JayDDee on July 21, 2021, 06:48:26 AM the slot the card is plugged into always comes up with an error. Did you try different slots? different cards? If the error follows the card it's a card problem, if it stays with the slot it's a slot problem. Title: Re: Hardware/Software Help Needed! Post by: batsonxl on July 21, 2021, 08:03:51 AM It is riser. Change riser.
If problem continues check card alone on working pc at pcie 16x slot Good luck Title: Re: Hardware/Software Help Needed! Post by: SilverWWW on July 21, 2021, 05:56:28 PM have you checked whether your card is ok? what about the power, is it sufficient to power up all of your cards? as one last resort, maybe try to clean the slot itself just in case there's some dust there. Yeah all these cards should be brand new unused, also I'm only using one card at the moment so the power shouldn't be an issue (1000W+ psu). If it's any extra help, when I plug in all 11 cards, they all come up red, despite everything being new. That why I think its a general problem rather than one specific to a card or riser.Title: Re: Hardware/Software Help Needed! Post by: batsonxl on July 21, 2021, 06:59:44 PM have you checked whether your card is ok? what about the power, is it sufficient to power up all of your cards? as one last resort, maybe try to clean the slot itself just in case there's some dust there. Yeah all these cards should be brand new unused, also I'm only using one card at the moment so the power shouldn't be an issue (1000W+ psu). If it's any extra help, when I plug in all 11 cards, they all come up red, despite everything being new. That why I think its a general problem rather than one specific to a card or riser.Simple way is adding 1 card at the time will help in most cases. Bring bios to default then try again adding 1 by 1. i have 2 asus b250 running them with 1200w + 1400w server psu. no problem at all. Once i had red slot then i changed riser problem resolved. Title: Re: Hardware/Software Help Needed! Post by: FP91G on July 21, 2021, 09:41:57 PM Hey yo, The best idea is to read the documentation for the motherboard.Currently in the process of setting up a new rig and am having some trouble with GPU detection after POST. For context, I'm using an ASUS B250 and it shows me a screen of which cards are working and which aren't right before launching BIOS. Anyways, on my very first POST, I had one card in and it detected fine - showed up green and everything. Then, for some reason, each time I relaunch BIOS, the slot the card is plugged into always comes up with an error. I went a tweaked around with the BIOS setting (detailed description below), but no luck. Was wondering if anyone had any ideas. Thanks! BIOS setting changes: - Changed primary display to CPU graphics from PCI-E - Changed both PCIe and PCIEX16_1 speeds from Gen1 to Auto - Disabled SATA ports 2-4 (not in use) - Enabled Power on by PCI-E - Disabled HD Audio Controller No big changes really, as you can see. Also, I've tried detecting the card on both Gen1 and 2, but no luck. Ideas? https://dlcdnets.asus.com/pub/ASUS/mb/LGA1151/B250_MINING_EXPERT/E13594_B250_MINING_EXPERT_UM_V2_WEB.pdf Read the mining mode info and check for BIOS updates for this motherboard 4G ?? Look on YouTube for a video on setting up this motherboard. |