|
Title: TB250 M.2 Conversion Post by: MCcryptonia on October 03, 2021, 06:42:07 AM I have a BiOSTAR MOBO TB250 with 6pcie slots and I notice it has a m.2 slot too, is there any conversion that I can use in that slot to use an extra GPU on the mobo? Any m.2 to pcie slot that can work perfectly with this motherboard?
Title: Re: TB250 M.2 Conversion Post by: miner29 on October 03, 2021, 02:21:31 PM Can try the m.2 to pcie adapter board. looks like usng the m.2 will disable sata 3-1 but that shouldnt be an issue. Do note slots 1-6 should be set to pcie gen 1 per the manual. Then only thing you can do is try. Adapter is about $8 on amazon.
Title: Re: TB250 M.2 Conversion Post by: Williamm07 on October 03, 2021, 02:41:15 PM M.2 to 4x or 1x pcie will work, it shouldn't cost you more than 10$ highest, this is the exact amount it's been sold in my country, just plug in your riser and the GPU I'm sure it will work, I've seen guys using this, also don't forget to change gen in bios to gen 2
https://i.imgur.com/aOjIdJa.jpg Title: Re: TB250 M.2 Conversion Post by: JayDDee on October 03, 2021, 02:46:06 PM For a mining rig it shouldn't be a problem as long as the m.2 slot supports PCIe/NVME (any mobo less than
5 years old does) and you have enough PCIe lanes available. They usually come together because more lanes are required to support an NVME device than a SATA device. Using a SATA or USB boot device also leaves more lanes available for use by GPUs. Mobos often have more ports that use PCIe than there are lanes available. The number of lanes is often determined by the CPU. A budget CPU like Celeron has fewer lanes making it trickier to feed all the GPUs. You may have to change the PCIe config in the BIOS to disable some uneeded devices, like extra SATA ports as previously mentioned or extra USB ports. Title: Re: TB250 M.2 Conversion Post by: Ceyflix-Rez on October 03, 2021, 04:39:54 PM For a mining rig it shouldn't be a problem as long as the m.2 slot supports PCIe/NVME (any mobo less than This have anything to do with my motherboard that refuse to work with 5 GPUs? I only make it work with 4gpus and if I insert the 5th the motherboard won't boot up, I've tried bios settings but the CPU in the MOBO is a core i3 processor, can i3 power more than 4gpus ?5 years old does) and you have enough PCIe lanes available. They usually come together because more lanes are required to support an NVME device than a SATA device. Using a SATA or USB boot device also leaves more lanes available for use by GPUs. Mobos often have more ports that use PCIe than there are lanes available. The number of lanes is often determined by the CPU. A budget CPU like Celeron has fewer lanes making it trickier to feed all the GPUs. You may have to change the PCIe config in the BIOS to disable some uneeded devices, like extra SATA ports as previously mentioned or extra USB ports. Title: Re: TB250 M.2 Conversion Post by: JayDDee on October 03, 2021, 05:11:04 PM For a mining rig it shouldn't be a problem as long as the m.2 slot supports PCIe/NVME (any mobo less than This have anything to do with my motherboard that refuse to work with 5 GPUs? I only make it work with 4gpus and if I insert the 5th the motherboard won't boot up, I've tried bios settings but the CPU in the MOBO is a core i3 processor, can i3 power more than 4gpus ?5 years old does) and you have enough PCIe lanes available. They usually come together because more lanes are required to support an NVME device than a SATA device. Using a SATA or USB boot device also leaves more lanes available for use by GPUs. Mobos often have more ports that use PCIe than there are lanes available. The number of lanes is often determined by the CPU. A budget CPU like Celeron has fewer lanes making it trickier to feed all the GPUs. You may have to change the PCIe config in the BIOS to disable some uneeded devices, like extra SATA ports as previously mentioned or extra USB ports. An i3 should be good. Do all the slots work if you don't use more than 4 at a time? The mobo specs should tell how lanes are shared. It could be a different problem, gen1 is often required to use more than 4 GPUs. |
