Title: Avalon 821, 841, 851 hash board repair manual Post by: GFDhd on July 21, 2022, 03:59:05 AM Hi guys, I recently got a repair manual for the AvalonMiner 8 series hash board. Share with you here, and if there are any questions, please help me to point out:
This tutorial applies to Avalon 821, 841, 851, and other series of miners. The article takes Avalon 821 as an example to explain the precautions and methods of A821 hash board maintenance. First, we need to understand how to connect the test fixture and hash board. The test fixture consists of the PMU board and the MM board (control board). The connection method is as follows: https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/test-fixture-connection-method.jpg PMU connection diagram: 12V power input port: connect to the power supply of the miner; VCore and GND: Connect the VCore and GND of the hash board to be tested; Signal output: connect to the signal port of the hash board to be tested; Connect with the A821 MM board: Connect the Avalon 821 PMU with the A821 MM board. https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/pmu-connection-diagram.jpg Notice: 1. The A821 MM board is connected to the A821 PMU. Due to the program settings, the DATA2 interface of A821 is connected to J8 of the PMU, and the DATA2 pin1 of the A821 MM board corresponds to the J8 pin2 of the A821 PMU; 2. The signal and VCore power of the A821 PMU are only output from the J6 connector and the VCore-2 side, so only the J6 side connector and the VCore-2 power output can be connected. Therefore, it is necessary to pay attention to the interface direction of the signal output end of the A821 PMU; like regular plugs, the pins are reversed. Pay attention to the order of the 12V power input ports, the top is GND (black), and the bottom is 12V (yellow); MM board (control board) connection diagram: https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/mm-board-connection-diagram.jpg Connect with A821 PMU board: A821 MM board is connected with the A821 PMU; Serial port connection: used to view the hash board test information on the computer screen; connect the computer USB port through the USB to TTL serial port module; The serial port connection sequence is: MM side PIN Serial port line sequence Pin 1 Ground Pin 2 TXD Pin 3 Receiving end FPGA reset button (the test button, which can be connected to an external foot switch or automatic reset switch): After the test program is completed, pressing the test button again will output a reset signal and restart the test. Hash board connection diagram: https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/hash-board-connection-diagram.jpg PMU output connection diagram: VCore Power Supply: Powering the hash board GND: Hash board power GND, the signal is connected to PMU and hash board, PMU transmits data to hash board through the data cable, and then transmits the calculated data back to A821 PMU through the data cable. https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/pmu-output-connection-diagram.jpg A821 hash board "Pin No.": Pin No. Signal Pin No. Signal Pin 1 12V Pin 2 1.8V Pin 3 1.8V Pin 4 RO Pin 5 Ground Pin 6 CO Pin 7 Ground Pin 8 DO Pin 9 Ground Pin 10 DI Pin 11 Ground Pin 12 CI Pin 13 Ground Pin 14 RI Notice: 1. Do not reverse the connection between VCore and GND; 2. The wiring sequence of the PMU board and the hash board; when connecting the signal line, do not insert the wrong or misplaced; otherwise, it will cause damage to the hash board, MM board, and PMU board. 3. The red and black power cables and signal cables must be connected well before the test; otherwise, the LDO of the hash board will be burned. 4. When testing the hash board, a cooling fan needs to be placed to dissipate heat; 5. Do not test the hash board for a long time; otherwise, the temperature will be too high. Avalon 821 hash board structure: When replacing the ASIC chip on the hash board, you need to replace the chip with the same Bin number according to the chip label on the hash board. https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/avalon-821-hash-board.jpg Hash board test steps: 1. Determine the status of the hash board; power on the hash board, and judge whether maintenance is required according to the status of the hash board indicator light: The status indicator is judged as follows: Green, the hash board is normal and does not need repair. Red, the hash board is abnormal and needs to be repaired. https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/hash-board-test.jpg 2. Determine whether there is a problem with the hash board through the serial port View the LOG information of the hash board running on the computer through the serial port debugging tool, as shown in the figure: Serial port debugging tool settings need to set the serial port number, the baud rate is set to 115200, the data bit is 8 bits, and the stop bit is 1 bit. https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/serial-port-debugging-tool.jpg 3. Coretest abnormal phenomenon judgment and repair If the following code appears in the LOG information, asic count = 26, miner 0 asic 21 pass 0, miner 0 asic 24 pass 0, it means that there is a problem with the A21 and A24 chips corresponding to the A821 hash board, and the A21 and A24-bit chips need to be replaced. Note: The BIN number of the chip to be replaced should correspond to the BIN number marked on the back of the hash board. https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/log-information.jpg 4. Loopback abnormal phenomenon and repair If asic count=0 appears in the LOG information, it means loopback fails; that is, the link of the hash board is unreachable, indicating that there is a problem with the signal transmission of the A821 hash board, and further testing is required. https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/asic-count-0.jpg First of all, we need to check whether the appearance of the components is damaged visually, or the welding is poor; LDO soldering problems: https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/ldo-soldering-problems.jpg Abnormal resistance: https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/abnormal-resistance.jpg If you can't see it with the naked eye, you need an oscilloscope or a Fluke 15B+ multimeter to locate the hash board problem quickly: 1. Use the Fluke 15B+ multimeter impedance gear to measure the impedance between the 12V test point and GND. If the impedance is between 0-100Ω, there is a problem with the LDOs (U1, U2) of A0-A5. Test the impedance of the A0-A5 VTOP test point and the VDD test point to determine whether the impedance is normal. If the impedances do not match, the corresponding LDOs (U1, U2) need to be replaced. https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/avalon-hash-board-test-point.jpg Test Point Impedance (Ω) Corresponding chip VTOP > 90Ω U1 VDD > 70KΩ U2 If the impedance of the test point is abnormal, the corresponding chip needs to be replaced. 2. Use an oscilloscope to test the CO signal of each group of chips. If there is no waveform, there is a problem with the chipset. First, you need to use a Fluke 15B+ multimeter to determine whether the output voltages of U1 and U2 meet the impedance value and voltage value. If not, you need to replace the corresponding power chip (U1, U2). The CO signal waveform is shown in the following figure: (The oscilloscope is set to AC; the amplitude is set to 1.00V/div, and the frequency is set to 500ns/div) https://www.zeusbtc.com/share/Avalon-8-series-hash-board-repair-manual/co-signal-waveform.jpg A821 hash board parameter reference: Signal Resistance (Ω) RO and GND 365K CO and GND 365K DO and GND 365K DI and GND 234K CI and GND 234K RI and GND 234K 12V and GND 64K 1.8V and GND 37K RO and CO 747K CO and DO 747K DO and DI 700K DI and CI 553K CI and RI 554K C and GND 1K D and GND 1K R and GND 1K A821 hash board voltage value: Voltage Voltage value VDD 1.8V VTOP 0.75V CORE 0.35V Notice: 1. Since the chip modules are in series mode, the signal is transmitted from the 25th chip module to the 0th chip module. So we need to check from the 25th chip to the 0th chip. If the front chip doesn't work, the back chip doesn't work either. The test fixture inspection will show that all chips cannot be found. 2. Confirm that each module's two adjacent signal waveforms are inconsistent. If they are consistent, you need to confirm the impedance of adjacent signals to determine whether the pins are short-circuited; 3. The signal voltage of each chip module is 1.8V. 4. If after repairing the hash board, all power supply circuit voltages and chip signals are normal. However, the hash rate cannot reach the original hash rate after the miner is turned on. You can replace the control board or use a USB programmer to brush the program of the EEPROM chip of the control board. The hash board will return to its normal hash rate. |