Title: S19J pro 104th NO HASH Post by: simy55 on December 25, 2023, 09:40:43 AM Hello,
My S19J Pro 104th stopped hash yesterday. Rate abnormal Temp abnormal Fault light is on. Im new to mining and would be nice with some support. Pool: Nicehash My log here: 2023-12-24 18:18:31 fails to write 1 2023-12-24 18:18:31 fails to read 0:1 2023-12-24 18:18:31 fails to write 1 2023-12-24 18:18:31 fails to read 0:1 2023-12-24 18:18:31 fails to write 1 2023-12-24 18:18:31 fails to read 0:1 2023-12-24 18:18:31 fails to write 1 2023-12-24 18:18:31 fails to read 0:1 2023-12-24 18:18:31 fails to write 1 2023-12-24 18:18:31 fails to read 0:1 2023-12-24 18:18:31 load chain 1 eeprom data 2023-12-24 18:18:34 load chain 2 eeprom data 2023-12-24 18:18:34 i2c_sim_init start 2023-12-24 18:18:34 init gpio477 2023-12-24 18:18:34 init gpio476 2023-12-24 18:18:34 i2c_sim_init end 2023-12-24 18:18:36 power open power_version = 0x75 2023-12-24 18:18:38 power is not calibrated 2023-12-24 18:18:40 miner type: Antminer S19j Pro 2023-12-24 18:18:40 multimachine mode 2023-12-24 18:18:40 load machine BHB42631 conf 2023-12-24 18:18:40 machine: BHB42631 2023-12-24 18:18:40 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3 2023-12-24 18:18:40 abandon mixboard! 2023-12-24 18:18:40 abandon mixboard! 2023-12-24 18:18:40 fan_eft: 1 fan_pwm: 80 2023-12-24 18:18:40 create thread get_nonce_and_register_thread 2023-12-24 18:18:40 fixed working voltage = 1360 2023-12-24 18:18:40 fixed frequency is 525 2023-12-24 18:18:40 Chain
2023-12-24 18:18:40 Chain [1] BOM Version: 0x0010 2023-12-24 18:18:40 Chain [2] PCB Version: 0x0130 2023-12-24 18:18:40 Chain [2] BOM Version: 0x0010 2023-12-24 18:18:40 bad chain ID = 3 2023-12-24 18:18:40 Fan control approved. 2023-12-24 18:18:40 uart_trans addr:0xf70a6000. 2023-12-24 18:18:40 max sensor number = 4 2023-12-24 18:18:40 STATUS_INITED: soc init complete! 2023-12-24 18:18:40 temperature_monitor_thread_start... 2023-12-24 18:18:40 cannot read tsensor via iic, chain: 1, slave: 72, addr: 0 2023-12-24 18:18:40 cannot read image temp for chain 1 2023-12-24 18:18:40 cannot read tsensor via iic, chain: 1, slave: 76, addr: 0 2023-12-24 18:18:40 cannot read image temp for chain 1 2023-12-24 18:18:41 cannot read tsensor via iic, chain: 1, slave: 72, addr: 0 2023-12-24 18:18:41 unable to read image temp for chain 1 2023-12-24 18:18:41 cannot read tsensor via iic, chain: 1, slave: 76, addr: 0 2023-12-24 18:18:41 unable to read image temp for chain 1 2023-12-24 18:18:42 cannot read tsensor via iic, chain: 1, slave: 72, addr: 0 2023-12-24 18:18:42 cannot read image temp for chain 1 2023-12-24 18:18:42 cannot read tsensor via iic, chain: 1, slave: 76, addr: 0 2023-12-24 18:18:42 cannot read image temp for chain 1 2023-12-24 18:18:42 over max temp, pcb temp 26 (max 75), chip temp 26 (max 95) pcb temp rise 0 chip temp rise 0, total_exit_failure 6 2023-12-24 18:18:42 Sweep error string = J0:6. 2023-12-24 18:18:42 ERROR_TEMP_TOO_HIGH: over max temp 2023-12-24 18:18:42 stop_mining: over max temp 2023-12-24 18:18:42 uninit_temp_info 2023-12-24 18:18:42 no longer reading temp... 2023-12-24 18:18:42 cancel thread 2023-12-24 18:18:42 *power off hashboard* 2023-12-24 18:18:42 starting... 2023-12-24 18:18:42 warning: power is not calibrated. 2023-12-24 18:18:42 Version number 65536 2023-12-24 18:18:42 Mask num 0x1fffe000 2023-12-24 18:18:42 opt_multi_version = 65536, interval timeout = 2945120 2023-12-24 18:18:42 freq = 525, percent = 90, hcn = 4993, timeout = 2945120 2023-12-24 18:18:44 power type version: 0x0075 2023-12-24 18:18:45 disable power watchdog: 0x0000 2023-12-24 18:18:46 temp monitor thread exit 2023-12-24 18:18:46 Initializing power, wait, this may take up to 2 minutes... Title: Re: S19J pro 104th NO HASH Post by: simy55 on December 25, 2023, 09:47:28 AM My room is around 27 celsius. No heating problem.
|