Title: S19k pro firmware 2024-02-21 upgrade stopped mining
Post by: glovl on February 28, 2024, 06:47:02 AM
log Please take a look. what is the issue? 024-02-28 06:05:45 ==========================capability start========================== 2024-02-28 06:05:45 board num = 3 2024-02-28 06:05:45 board id = 0, chain num = 1 2024-02-28 06:05:45 chain id = 0 2024-02-28 06:05:45 board id = 1, chain num = 1 2024-02-28 06:05:45 chain id = 1 2024-02-28 06:05:45 board id = 2, chain num = 1 2024-02-28 06:05:45 chain id = 2 2024-02-28 06:05:45 ==========================capability end============================ 2024-02-28 06:05:45 chain num = 3 2024-02-28 06:05:50 load chain 0 eeprom data 2024-02-28 06:05:54 load chain 1 eeprom data 2024-02-28 06:05:58 load chain 2 eeprom data 2024-02-28 06:05:58 eeprom load ret:0 2024-02-28 06:05:58 miner:BHB56901,board_name:BHB56902 2024-02-28 06:05:58 miner:BHB56902,board_name:BHB56902 2024-02-28 06:05:58 create thread get_nonce_and_register_thread 2024-02-28 06:05:58 fixed working voltage = 1350 2024-02-28 06:05:58 Chain [0] PCB Version: 0x0300 2024-02-28 06:05:58 Chain [0] BOM Version: 0x0000 2024-02-28 06:05:58 Chain [1] PCB Version: 0x0300 2024-02-28 06:05:58 Chain [1] BOM Version: 0x0000 2024-02-28 06:05:58 Chain [2] PCB Version: 0x0300 2024-02-28 06:05:58 Chain [2] BOM Version: 0x0000 2024-02-28 06:05:58 Fan check passed. 2024-02-28 06:05:58 init fan pid target=55 2024-02-28 06:05:58 max sensor num = 4 2024-02-28 06:05:58 STATUS_INITED: soc init done! 2024-02-28 06:05:58 temperature_monitor_thread start... 2024-02-28 06:06:00 start to init... 2024-02-28 06:06:01 start up min temp by 75a = 12, limit -25 2024-02-28 06:06:01 i2c_sim_init start 2024-02-28 06:06:01 power i2c device:sim_dev addr:0x10 fd:255 2024-02-28 06:06:01 i2c_sim_init end 2024-02-28 06:06:03 power open power_version = 0x76 2024-02-28 06:06:06 power is Calibrated 2024-02-28 06:06:06 power sn:DGQG329BCJIAB1157 2024-02-28 06:06:06 enable_power_calibration,calibration date:211208. 2024-02-28 06:06:07 power type version: 0x0076 2024-02-28 06:06:08 disable power watchdog: 0x0000 2024-02-28 06:06:09 Initializing the power, please wait, this may take up to 2 minutes... 2024-02-28 06:08:56 Slept 167 seconds, diff = 3. 2024-02-28 06:09:06 set_voltage_by_steps to 1300. 2024-02-28 06:09:08 set_voltage_by_steps to 1500. 2024-02-28 06:09:16 Chain[0]: find 77 asic, times 0 2024-02-28 06:09:18 Chain[1]: find 77 asic, times 0 2024-02-28 06:09:20 Chain[2]: find 77 asic, times 0 2024-02-28 06:09:25 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 4 2024-02-28 06:09:29 fixed frequency is 590 2024-02-28 06:09:29 Bring up temperature is 13 2024-02-28 06:09:29 set uart relay 2024-02-28 06:09:29 set UART baud to 1000000 2024-02-28 06:09:30 create thread check_miner_status_thread 2024-02-28 06:09:30 create thread check_system_work_thread 2024-02-28 06:09:30 create thread debug_freq_thread 2024-02-28 06:09:30 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 4 2024-02-28 06:09:30 start do_core_reset 2024-02-28 06:09:41 end do_core_reset 2024-02-28 06:09:41 noraml inc freq voltage 2024-02-28 06:09:41 set_voltage_by_steps to 1500. 2024-02-28 06:09:45 Version num 65536 2024-02-28 06:09:45 Mask num 0x1fffe000 2024-02-28 06:09:45 opt_multi_version = 65536, interval timeout = 2620657 2024-02-28 06:09:45 freq = 590, percent = 90, hcn = 4442, timeout = 2620657 2024-02-28 06:09:45 (null) 2024-02-28 06:09:59 freq 200 waiting board temp to 35,curr temp 14 2024-02-28 06:10:09 freq 200 waiting board temp to 35,curr temp 14 2024-02-28 06:10:19 freq 200 waiting board temp to 35,curr temp 15 2024-02-28 06:10:29 freq 200 waiting board temp to 35,curr temp 16 2024-02-28 06:10:39 freq 200 waiting board temp to 35,curr temp 18 2024-02-28 06:10:49 freq 200 waiting board temp to 35,curr temp 19 2024-02-28 06:10:59 freq 200 waiting board temp to 35,curr temp 20 2024-02-28 06:11:09 freq 200 waiting board temp to 35,curr temp 21 2024-02-28 06:11:19 freq 200 waiting board temp to 35,curr temp 22 2024-02-28 06:11:29 freq 200 waiting board temp to 35,curr temp 22 2024-02-28 06:11:39 freq 200 waiting board temp to 35,curr temp 22 2024-02-28 06:11:49 freq 200 waiting board temp to 35,curr temp 23 2024-02-28 06:12:18 freq 400 waiting board temp to 35,curr temp 24 2024-02-28 06:12:28 freq 400 waiting board temp to 35,curr temp 25 2024-02-28 06:12:38 freq 400 waiting board temp to 35,curr temp 26 2024-02-28 06:12:48 freq 400 waiting board temp to 35,curr temp 28 2024-02-28 06:12:58 freq 400 waiting board temp to 35,curr temp 28 2024-02-28 06:13:08 freq 400 waiting board temp to 35,curr temp 29 2024-02-28 06:13:18 freq 400 waiting board temp to 35,curr temp 30 2024-02-28 06:13:28 freq 400 waiting board temp to 35,curr temp 31 2024-02-28 06:13:38 freq 400 waiting board temp to 35,curr temp 31 2024-02-28 06:13:48 freq 400 waiting board temp to 35,curr temp 32 2024-02-28 06:13:58 freq 400 waiting board temp to 35,curr temp 32 2024-02-28 06:14:08 freq 400 waiting board temp to 35,curr temp 33 2024-02-28 06:14:32 set_voltage_by_steps to 1480. 2024-02-28 06:14:35 set_voltage_by_steps to 1460. 2024-02-28 06:14:38 set_voltage_by_steps to 1440. 2024-02-28 06:14:42 set_voltage_by_steps to 1420. 2024-02-28 06:14:45 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 4 2024-02-28 06:14:45 get board temp:34 2024-02-28 06:14:45 waiting board temp come to 35 2024-02-28 06:14:45 waiting board temp to 35,curr temp 34 2024-02-28 06:14:55 waiting board temp to 35,curr temp 35 2024-02-28 06:15:05 get board temp:35 2024-02-28 06:15:21 set voltage to work voltage 2024-02-28 06:15:21 set_voltage_by_steps to 1410. 2024-02-28 06:15:23 set_voltage_by_steps to 1400. 2024-02-28 06:15:25 set_voltage_by_steps to 1390. 2024-02-28 06:15:27 set_voltage_by_steps to 1380. 2024-02-28 06:15:29 set_voltage_by_steps to 1370. 2024-02-28 06:15:31 set_voltage_by_steps to 1360. 2024-02-28 06:15:33 set_voltage_by_steps to 1356. 2024-02-28 06:15:35 create thread check_nonce_status_thread 2024-02-28 06:15:35 create thread power_heart_beat_thread 2024-02-28 06:15:35 Init done! 2024-02-28 06:15:35 STATUS_OKAY 2024-02-28 06:15:35 start the cached job 2024-02-28 06:15:35 set_start_time_point total_tv_start_sys=609 total_tv_end_sys=610 2024-02-28 06:15:36 enable power watchdog: 0x0001 2024-02-28 06:15:50 chain[1] asic[6] [70] [416] 2024-02-28 06:15:50 chain[1] asic[7] [266] [157] 2024-02-28 06:15:50 chain[1] asic[10] [437] [4] 2024-02-28 06:15:50 chain[1] asic[20] [330] [196] 2024-02-28 06:15:50 chain[2] asic[0] [444] [15] 2024-02-28 06:15:50 chain[2] asic[1] [433] [3] 2024-02-28 06:15:50 chain[2] asic[2] [356] [63] 2024-02-28 06:15:50 chain[2] asic[3] [314] [0] 2024-02-28 06:15:50 chain[2] asic[4] [309] [0] 2024-02-28 06:15:50 chain[2] asic[5] [312] [0] 2024-02-28 06:15:50 chain[2] bad asic num: 6 6 0 2024-02-28 06:15:50 chain[2] asic[5] [312] 26454-26142 [0] 17-17 2024-02-28 06:15:50 chain[2] asic[6] [62] [157] 2024-02-28 06:15:50 chain[2] asic[7] [197] [178] 2024-02-28 06:15:50 chain[2] asic[8] [259] [172] 2024-02-28 06:15:50 chain[2] asic[9] [447] [3] 2024-02-28 06:15:50 chain[2] asic[10] [448] [3] 2024-02-28 06:15:50 chain[2] asic[11] [452] [0] 2024-02-28 06:15:55 chain[0] asic[62] [446] [115] 2024-02-28 06:15:55 chain[1] asic[5] [448] [91] 2024-02-28 06:15:55 chain[1] asic[6] [52] [391] 2024-02-28 06:15:55 chain[1] asic[7] [314] [144] 2024-02-28 06:15:55 chain[1] asic[8] [443] [5] 2024-02-28 06:15:55 chain[1] asic[9] [412] [3] 2024-02-28 06:15:55 chain[1] asic[20] [329] [200] 2024-02-28 06:15:55 chain[2] asic[0] [417] [11] 2024-02-28 06:15:55 chain[2] asic[2] [335] [80] 2024-02-28 06:15:55 chain[2] asic[3] [319] [4] 2024-02-28 06:15:55 chain[2] asic[4] [324] [0] 2024-02-28 06:15:55 chain[2] asic[5] [294] [2] 2024-02-28 06:15:55 chain[2] asic[6] [64] [164] 2024-02-28 06:15:55 chain[2] bad asic num: 6 6 1 2024-02-28 06:15:55 chain[2] asic[6] [64] 25312-25248 [164] 1002-838 2024-02-28 06:15:55 chain[2] asic[7] [177] [200] 2024-02-28 06:15:55 chain[2] asic[8] [278] [148] 2024-02-28 06:15:55 chain[2] asic[10] [435] [4] 2024-02-28 06:16:00 chain[0] asic[62] [441] [95] 2024-02-28 06:16:00 chain[1] asic[6] [60] [415] 2024-02-28 06:16:00 chain[1] asic[7] [272] [170] 2024-02-28 06:16:00 chain[1] asic[8] [436] [6] 2024-02-28 06:16:00 chain[1] asic[10] [424] [3] 2024-02-28 06:16:00 chain[1] asic[20] [323] [222] 2024-02-28 06:16:00 chain[2] asic[0] [448] [10] 2024-02-28 06:16:00 chain[2] asic[2] [314] [71] 2024-02-28 06:16:00 chain[2] asic[3] [318] [0] 2024-02-28 06:16:00 chain[2] asic[4] [306] [0] 2024-02-28 06:16:00 chain[2] asic[5] [259] [0] 2024-02-28 06:16:00 chain[2] asic[6] [71] [162] 2024-02-28 06:16:00 chain[2] bad asic num: 6 6 2 2024-02-28 06:16:00 chain[2] asic[6] [71] 25383-25312 [162] 1164-1002 2024-02-28 06:16:00 Sweep error string = N:3. 2024-02-28 06:16:00 ERROR_UNBALANCE: Unbalance happened, waiting! 2024-02-28 06:16:00 stop_mining_waiting: Unbalance happened, waiting! 2024-02-28 06:16:00 uninit_temp_info 2024-02-28 06:16:00 do not read temp anymore... 2024-02-28 06:16:00 cancel thread 2024-02-28 06:16:00 cancel thread 2024-02-28 06:16:00 cancel thread 2024-02-28 06:16:00 ****power off hashboard**** 2024-02-28 06:16:00 power off 2024-02-28 06:16:01 temp monitor thread exit it used to be like this before the update 1970-01-01 00:00:13 get high_temp_sub_freq failed,set default high_temp_sub_freq = 10 1970-01-01 00:00:13 get mix boardname[0][BHB56902], name:BHB56902 1970-01-01 00:00:18 power off 2024-02-25 23:57:18 ==========================capability start========================== 2024-02-25 23:57:18 board num = 3 2024-02-25 23:57:18 board id = 0, chain num = 1 2024-02-25 23:57:18 chain id = 0 2024-02-25 23:57:18 board id = 1, chain num = 1 2024-02-25 23:57:18 chain id = 1 2024-02-25 23:57:18 board id = 2, chain num = 1 2024-02-25 23:57:18 chain id = 2 2024-02-25 23:57:18 ==========================capability end============================ 2024-02-25 23:57:18 chain num = 3 2024-02-25 23:57:22 load chain 0 eeprom data 2024-02-25 23:57:26 load chain 1 eeprom data 2024-02-25 23:57:30 load chain 2 eeprom data 2024-02-25 23:57:30 eeprom load ret:0 2024-02-25 23:57:30 miner:BHB56901,board_name:BHB56902 2024-02-25 23:57:30 miner:BHB56902,board_name:BHB56902 2024-02-25 23:57:30 create thread get_nonce_and_register_thread 2024-02-25 23:57:30 fixed working voltage = 1350 2024-02-25 23:57:30 Chain [0] PCB Version: 0x0300 2024-02-25 23:57:30 Chain [0] BOM Version: 0x0000 2024-02-25 23:57:30 Chain [1] PCB Version: 0x0300 2024-02-25 23:57:30 Chain [1] BOM Version: 0x0000 2024-02-25 23:57:30 Chain [2] PCB Version: 0x0300 2024-02-25 23:57:30 Chain [2] BOM Version: 0x0000 2024-02-25 23:57:30 Fan check passed. 2024-02-25 23:57:30 init fan pid target=55 2024-02-25 23:57:30 max sensor num = 4 2024-02-25 23:57:30 STATUS_INITED: soc init done! 2024-02-25 23:57:30 temperature_monitor_thread start... 2024-02-25 23:57:33 start to init... 2024-02-25 23:57:33 i2c_sim_init start 2024-02-25 23:57:33 power i2c device:sim_dev addr:0x10 fd:255 2024-02-25 23:57:33 i2c_sim_init end 2024-02-25 23:57:34 power open power_version = 0x76 2024-02-25 23:57:37 power is Calibrated 2024-02-25 23:57:37 power sn:DGQG329BCJIAB1157 2024-02-25 23:57:37 enable_power_calibration,calibration date:211208. 2024-02-25 23:57:38 power type version: 0x0076 2024-02-25 23:57:40 disable power watchdog: 0x0000 2024-02-25 23:57:41 Initializing the power, please wait, this may take up to 2 minutes... 2024-02-25 23:59:01 Slept 80 seconds, diff = 0. 2024-02-25 23:59:11 set_voltage_by_steps to 1300. 2024-02-25 23:59:13 set_voltage_by_steps to 1500. 2024-02-25 23:59:18 start up min temp by 75a = 23 2024-02-25 23:59:21 Chain[0]: find 77 asic, times 0 2024-02-25 23:59:23 Chain[1]: find 77 asic, times 0 2024-02-25 23:59:25 Chain[2]: find 77 asic, times 0 2024-02-25 23:59:30 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 4 2024-02-25 23:59:34 fixed frequency is 590 2024-02-25 23:59:34 Bring up temperature is 24 2024-02-25 23:59:34 set uart relay 2024-02-25 23:59:34 set UART baud to 1000000 2024-02-25 23:59:34 create thread check_miner_status_thread 2024-02-25 23:59:34 create thread check_system_work_thread 2024-02-25 23:59:34 create thread inc_freq_matrix_thread 2024-02-25 23:59:34 create thread debug_freq_thread 2024-02-25 23:59:34 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 4 2024-02-25 23:59:34 start do_core_reset 2024-02-25 23:59:46 end do_core_reset 2024-02-25 23:59:46 noraml inc freq voltage 2024-02-25 23:59:46 set_voltage_by_steps to 1500. 2024-02-26 00:00:20 set_voltage_by_steps to 1480. 2024-02-26 00:00:23 set_voltage_by_steps to 1460. 2024-02-26 00:00:26 set_voltage_by_steps to 1440. 2024-02-26 00:00:29 set_voltage_by_steps to 1420. 2024-02-26 00:00:31 set_voltage_by_steps to 1400. 2024-02-26 00:00:35 get board temp:31 2024-02-26 00:00:35 create thread power_heart_beat_thread 2024-02-26 00:00:35 waiting board temp come to 35 2024-02-26 00:00:35 Init done! 2024-02-26 00:00:35 STATUS_OKAY 2024-02-26 00:00:35 start the cached job 2024-02-26 00:00:35 Version num 65536 2024-02-26 00:00:35 Mask num 0x1fffe000 2024-02-26 00:00:35 opt_multi_version = 65536, interval timeout = 2620657 2024-02-26 00:00:35 freq = 590, percent = 90, hcn = 4442, timeout = 2620657 2024-02-26 00:00:35 set_start_time_point total_tv_start_sys=217 total_tv_end_sys=218 2024-02-26 00:00:36 enable power watchdog: 0x0001 2024-02-26 00:00:45 waiting board temp to 35,curr temp 33 when time 10s 2024-02-26 00:00:50 get board temp:35 2024-02-26 00:00:51 set voltage to work voltage 2024-02-26 00:00:51 set_voltage_by_steps to 1390. 2024-02-26 00:00:53 set_voltage_by_steps to 1380. 2024-02-26 00:00:55 set_voltage_by_steps to 1370. 2024-02-26 00:00:57 set_voltage_by_steps to 1360. 2024-02-26 00:00:59 set_voltage_by_steps to 1350. 2024-02-26 00:07:33 5m later restore pid to 52 2024-02-26 00:29:42 30m avg rate is 112239.56 in 29 mins 2024-02-26 00:59:50 30m avg rate is 111509.82 in 30 mins 2024-02-26 01:29:59 30m avg rate is 110763.79 in 30 mins 2024-02-26 02:00:07 30m avg rate is 110760.15 in 30 mins 2024-02-26 02:30:16 30m avg rate is 110972.22 in 30 mins 2024-02-26 03:00:24 30m avg rate is 110731.40 in 30 mins 2024-02-26 03:30:33 30m avg rate is 110822.75 in 30 mins 2024-02-26 04:00:41 30m avg rate is 110491.80 in 30 mins 2024-02-26 04:30:49 30m avg rate is 111037.91 in 30 mins 2024-02-26 05:00:58 30m avg rate is 110729.58 in 30 mins 2024-02-26 05:31:06 30m avg rate is 110612.45 in 30 mins 2024-02-26 06:01:15 30m avg rate is 110649.30 in 30 mins 2024-02-26 06:31:23 30m avg rate is 111217.82 in 30 mins 2024-02-26 07:01:32 30m avg rate is 110969.79 in 30 mins 2024-02-26 07:31:40 30m avg rate is 110628.02 in 30 mins 2024-02-26 08:01:48 30m avg rate is 110334.08 in 30 mins 2024-02-26 08:31:57 30m avg rate is 110215.09 in 30 mins 2024-02-26 09:02:06 30m avg rate is 110011.34 in 30 mins 2024-02-26 09:32:14 30m avg rate is 110253.85 in 30 mins 2024-02-26 10:02:23 30m avg rate is 109860.55 in 30 mins 2024-02-26 10:32:31 30m avg rate is 110293.35 in 30 mins 2024-02-26 11:02:40 30m avg rate is 110273.48 in 30 mins 2024-02-26 11:32:49 30m avg rate is 110405.19 in 30 mins 2024-02-26 12:02:57 30m avg rate is 110037.52 in 30 mins 2024-02-26 12:33:05 30m avg rate is 110353.53 in 30 mins 2024-02-26 13:03:14 30m avg rate is 110056.37 in 30 mins 2024-02-26 13:33:22 30m avg rate is 111197.76 in 30 mins 2024-02-26 14:03:31 30m avg rate is 111247.71 in 30 mins 2024-02-26 14:33:40 30m avg rate is 110887.18 in 30 mins 2024-02-26 15:03:49 30m avg rate is 110713.34 in 30 mins 2024-02-26 15:33:57 30m avg rate is 110237.44 in 30 mins 2024-02-26 16:04:06 30m avg rate is 110418.82 in 30 mins 2024-02-26 16:34:15 30m avg rate is 110582.06 in 30 mins 2024-02-26 17:04:23 30m avg rate is 110761.36 in 30 mins 2024-02-26 17:34:32 30m avg rate is 111006.28 in 30 mins 2024-02-26 18:04:40 30m avg rate is 110964.93 in 30 mins 2024-02-26 18:34:49 30m avg rate is 110656.21 in 30 mins 2024-02-26 19:04:57 30m avg rate is 110565.04 in 30 mins 2024-02-26 19:35:06 30m avg rate is 110483.89 in 30 mins 2024-02-26 20:05:15 30m avg rate is 110952.82 in 30 mins 2024-02-26 20:35:24 30m avg rate is 110811.20 in 30 mins 2024-02-26 21:05:33 30m avg rate is 110988.07 in 30 mins 2024-02-26 21:35:41 30m avg rate is 110444.09 in 30 mins 2024-02-26 22:05:50 30m avg rate is 110703.43 in 30 mins 2024-02-26 22:35:58 30m avg rate is 110529.18 in 30 mins 2024-02-26 23:06:07 30m avg rate is 110341.59 in 30 mins 2024-02-26 23:36:15 30m avg rate is 110353.53 in 30 mins 2024-02-27 00:06:24 30m avg rate is 110505.18 in 30 mins 2024-02-27 00:36:33 30m avg rate is 110230.75 in 30 mins 2024-02-27 01:06:41 30m avg rate is 110185.77 in 30 mins 2024-02-27 01:36:50 30m avg rate is 110064.88 in 30 mins 2024-02-27 02:06:58 30m avg rate is 109594.38 in 30 mins 2024-02-27 02:37:07 30m avg rate is 109817.98 in 30 mins 2024-02-27 03:07:15 30m avg rate is 110267.83 in 30 mins 2024-02-27 03:37:24 30m avg rate is 110014.98 in 30 mins 2024-02-27 04:07:33 30m avg rate is 110035.69 in 30 mins 2024-02-27 04:37:42 30m avg rate is 109766.39 in 30 mins 2024-02-27 05:07:50 30m avg rate is 110090.96 in 30 mins 2024-02-27 05:37:59 30m avg rate is 109887.31 in 30 mins 2024-02-27 06:08:08 30m avg rate is 109629.03 in 30 mins 2024-02-27 06:38:17 30m avg rate is 109869.11 in 30 mins 2024-02-27 07:08:25 30m avg rate is 109765.18 in 30 mins 2024-02-27 07:38:34 30m avg rate is 109758.49 in 30 mins 2024-02-27 08:08:43 30m avg rate is 109660.03 in 30 mins 2024-02-27 08:38:52 30m avg rate is 109764.46 in 30 mins 2024-02-27 09:09:01 30m avg rate is 109991.28 in 30 mins 2024-02-27 09:39:09 30m avg rate is 109847.78 in 30 mins 2024-02-27 10:09:18 30m avg rate is 109472.82 in 30 mins 2024-02-27 10:39:27 30m avg rate is 109754.84 in 30 mins 2024-02-27 11:09:35 30m avg rate is 109389.55 in 30 mins 2024-02-27 11:39:44 30m avg rate is 110044.76 in 30 mins 2024-02-27 12:09:53 30m avg rate is 109548.58 in 30 mins 2024-02-27 12:40:02 30m avg rate is 109665.50 in 30 mins 2024-02-27 13:10:11 30m avg rate is 110619.74 in 30 mins 2024-02-27 13:40:20 30m avg rate is 110149.91 in 30 mins 2024-02-27 14:10:28 30m avg rate is 110508.52 in 30 mins 2024-02-27 14:40:37 30m avg rate is 110661.47 in 30 mins 2024-02-27 15:10:46 30m avg rate is 110596.04 in 30 mins 2024-02-27 15:40:54 30m avg rate is 110229.54 in 30 mins 2024-02-27 16:11:03 30m avg rate is 110839.04 in 30 mins 2024-02-27 16:41:12 30m avg rate is 111061.01 in 30 mins 2024-02-27 17:11:20 30m avg rate is 111282.25 in 30 mins 2024-02-27 17:41:29 30m avg rate is 110803.77 in 30 mins 2024-02-27 18:11:38 30m avg rate is 110980.17 in 30 mins 2024-02-27 18:41:46 30m avg rate is 110542.88 in 30 mins and always abnormal hashrate since I bought it
Title: Re: S19k pro firmware 2024-02-21 upgrade stopped mining
Post by: BitMaxz on February 28, 2024, 11:02:02 AM
Why did you update it to the new firmware? if it's working fine?
Anyway, there is an SD card recovery image would you mind to try flashing the unit through the SD card? You can download the TF card image from the link below.
- https://shop.bitmain.com/support/download
Update here if the issue is fixed or not.
Title: Re: S19k pro firmware 2024-02-21 upgrade stopped mining
Post by: glovl on February 28, 2024, 03:43:42 PM
I did upgrade because I had abnormal hashrate. And it was working stable only at normal performance, at high performance it was restarting a couple of times everyday.
Any idea what does this message mean? 2024-02-28 06:16:00 Sweep error string = N:3. 2024-02-28 06:16:00 ERROR_UNBALANCE: Unbalance happened, waiting!
Will update here. Ty for response
Title: Re: S19k pro firmware 2024-02-21 upgrade stopped mining
Post by: philipma1957 on February 28, 2024, 04:30:06 PM
I did upgrade because I had abnormal hashrate. And it was working stable only at normal performance, at high performance it was restarting a couple of times everyday.
Any idea what does this message mean? 2024-02-28 06:16:00 Sweep error string = N:3. 2024-02-28 06:16:00 ERROR_UNBALANCE: Unbalance happened, waiting!
Will update here. Ty for response
the new firmware broke it. whatsminer sometimes shows unbalanced. I never saw this with bitmain. my guess is you have 1 shit board. that is why you underhashed with old firmware but you hashed. i would try using braiins or even buy a brains hashboard if you can not get a sd card to work. https://altairtech.io/product/braiins-antminer-microsdc/ https://altairtech.io/product/bcb/ if you run braiins you can isolate the shitty hashboard.
Title: Re: S19k pro firmware 2024-02-21 upgrade stopped mining
Post by: glovl on February 28, 2024, 07:13:47 PM
I took Miner out of a noise box and reattached power cables. Since then everything has been working fine. The abnormal hashrate issue is gone too. Didnt touch the firmware after the update 1970-01-01 00:00:20 ==========================capability end============================ 1970-01-01 00:00:20 chain num = 3 2024-02-28 16:37:43 load chain 0 eeprom data 2024-02-28 16:37:47 load chain 1 eeprom data 2024-02-28 16:37:51 load chain 2 eeprom data 2024-02-28 16:37:51 eeprom load ret:0 2024-02-28 16:37:51 miner:BHB56901,board_name:BHB56902 2024-02-28 16:37:51 miner:BHB56902,board_name:BHB56902 2024-02-28 16:37:51 create thread get_nonce_and_register_thread 2024-02-28 16:37:51 fixed working voltage = 1420 2024-02-28 16:37:51 Chain [0] PCB Version: 0x0300 2024-02-28 16:37:51 Chain [0] BOM Version: 0x0000 2024-02-28 16:37:51 Chain [1] PCB Version: 0x0300 2024-02-28 16:37:51 Chain [1] BOM Version: 0x0000 2024-02-28 16:37:51 Chain [2] PCB Version: 0x0300 2024-02-28 16:37:51 Chain [2] BOM Version: 0x0000 2024-02-28 16:37:51 Fan check passed. 2024-02-28 16:37:51 init fan pid target=60 2024-02-28 16:37:51 max sensor num = 4 2024-02-28 16:37:51 STATUS_INITED: soc init done! 2024-02-28 16:37:51 temperature_monitor_thread start... 2024-02-28 16:37:54 start to init... 2024-02-28 16:37:55 start up min temp by 75a = 20, limit -25 2024-02-28 16:37:55 i2c_sim_init start 2024-02-28 16:37:55 power i2c device:sim_dev addr:0x10 fd:255 2024-02-28 16:37:55 i2c_sim_init end 2024-02-28 16:37:56 power open power_version = 0x76 2024-02-28 16:37:59 power is Calibrated 2024-02-28 16:37:59 power sn:DGQG329BCJIAB1157 2024-02-28 16:37:59 enable_power_calibration,calibration date:211208. 2024-02-28 16:38:00 power type version: 0x0076 2024-02-28 16:38:02 disable power watchdog: 0x0000 2024-02-28 16:38:03 Initializing the power, please wait, this may take up to 2 minutes... 2024-02-28 16:40:03 Slept 120 seconds, diff = 0. 2024-02-28 16:40:13 set_voltage_by_steps to 1300. 2024-02-28 16:40:15 set_voltage_by_steps to 1500. 2024-02-28 16:40:22 Chain[0]: find 77 asic, times 0 2024-02-28 16:40:24 Chain[1]: find 77 asic, times 0 2024-02-28 16:40:26 Chain[2]: find 77 asic, times 0 2024-02-28 16:40:31 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 4 2024-02-28 16:40:36 fixed frequency is 670 2024-02-28 16:40:36 Bring up temperature is 25 2024-02-28 16:40:36 set uart relay 2024-02-28 16:40:36 set UART baud to 1000000 2024-02-28 16:40:36 create thread check_miner_status_thread 2024-02-28 16:40:36 create thread check_system_work_thread 2024-02-28 16:40:36 create thread debug_freq_thread 2024-02-28 16:40:36 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 4 2024-02-28 16:40:36 start do_core_reset 2024-02-28 16:40:48 end do_core_reset 2024-02-28 16:40:48 noraml inc freq voltage 2024-02-28 16:40:48 set_voltage_by_steps to 1500. 2024-02-28 16:40:52 Version num 65536 2024-02-28 16:40:52 Mask num 0x1fffe000 2024-02-28 16:40:52 opt_multi_version = 65536, interval timeout = 2307743 2024-02-28 16:40:52 freq = 670, percent = 90, hcn = 3912, timeout = 2307743 2024-02-28 16:40:52 (null) 2024-02-28 16:41:03 freq 200 waiting board temp to 35,curr temp 26 2024-02-28 16:41:13 freq 200 waiting board temp to 35,curr temp 27 2024-02-28 16:41:23 freq 200 waiting board temp to 35,curr temp 28 2024-02-28 16:41:33 freq 200 waiting board temp to 35,curr temp 29 2024-02-28 16:41:43 freq 200 waiting board temp to 35,curr temp 30 2024-02-28 16:41:53 freq 200 waiting board temp to 35,curr temp 31 2024-02-28 16:42:03 freq 200 waiting board temp to 35,curr temp 31 2024-02-28 16:42:13 freq 200 waiting board temp to 35,curr temp 32 2024-02-28 16:42:23 freq 200 waiting board temp to 35,curr temp 32 2024-02-28 16:42:33 freq 200 waiting board temp to 35,curr temp 33 2024-02-28 16:42:43 freq 200 waiting board temp to 35,curr temp 33 2024-02-28 16:42:53 freq 200 waiting board temp to 35,curr temp 33 2024-02-28 16:43:19 freq 400 waiting board temp to 35,curr temp 34 2024-02-28 16:43:29 freq 400 waiting board temp to 35,curr temp 35 2024-02-28 16:43:59 set_voltage_by_steps to 1480. 2024-02-28 16:44:02 set_voltage_by_steps to 1460. 2024-02-28 16:44:04 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 4 2024-02-28 16:44:04 get board temp:38 2024-02-28 16:44:04 waiting board temp come to 35 2024-02-28 16:44:04 get board temp:38 2024-02-28 16:44:21 set voltage to work voltage 2024-02-28 16:44:21 set_voltage_by_steps to 1450. 2024-02-28 16:44:23 set_voltage_by_steps to 1440. 2024-02-28 16:44:25 set_voltage_by_steps to 1430. 2024-02-28 16:44:27 set_voltage_by_steps to 1420. 2024-02-28 16:44:29 create thread check_nonce_status_thread 2024-02-28 16:44:29 create thread power_heart_beat_thread 2024-02-28 16:44:29 Init done! 2024-02-28 16:44:29 STATUS_OKAY 2024-02-28 16:44:29 start the cached job 2024-02-28 16:44:29 set_start_time_point total_tv_start_sys=431 total_tv_end_sys=432 2024-02-28 16:44:31 enable power watchdog: 0x0001 2024-02-28 16:57:20 10m later restore pid to 58 2024-02-28 17:03:37 15m later restore pid to 56 2024-02-28 17:09:54 20m later restore pid to 54 2024-02-28 17:14:37 30m avg rate is 138979.97 in 30 mins 2024-02-28 17:44:46 30m avg rate is 139204.01 in 30 mins 2024-02-28 18:14:54 30m avg rate is 139767.51 in 30 mins 2024-02-28 18:45:03 30m avg rate is 139701.19 in 30 mins
Title: Re: S19k pro firmware 2024-02-21 upgrade stopped mining
Post by: frost047 on June 04, 2024, 07:53:12 AM
i'm having the same issue, but I think its not firmware issue it was electricity that was unbalanced during sometimes for me it was around 1PM, if you think there's another solution please tell
Title: Re: S19k pro firmware 2024-02-21 upgrade stopped mining
Post by: BitMaxz on June 04, 2024, 09:33:07 PM
i'm having the same issue, but I think its not firmware issue it was electricity that was unbalanced during sometimes for me it was around 1PM, if you think there's another solution please tell
What is the unit's current status? OP's problem seems solved by just taking out the miner from the noise box which means the reason behind his issue is the overheating issue this is a common issue when you put your miner into any box for noise reduction. Do you have a similar issue? And you already tried to take the unit out of the box to test? or run the unit far from the wall? I mean the hot air out that came from the unit should not bouncing back to the unit it would cause some issues like overheating. If not, better give more info about your issue by posting the logs here or make a new thread.
|