Title: S19KPRO SINGLE HASHBOAD NOT MINING.
Post by: irfan655 on July 22, 2024, 07:52:20 PM
This is my miner log Anyone please 2015-01-01 00:00:16 This is fix-freq version
2015-01-01 00:00:16 Miner compile time: Wed Nov 15 14:47:56 CST 2023 type: Antminer S19k Pro
2015-01-01 00:00:16 commit version: 143b498a 2023-11-09 14:37:23, build by: jenkins 2023-11-15 15:11:08
2015-01-01 00:00:16 opt_multi_version = 1
2015-01-01 00:00:16 opt_bitmain_ab = 1
2015-01-01 00:00:16 mid_auto_gen = 1
2015-01-01 00:00:16 opt_bitmain_work_mode = 2
2015-01-01 00:00:16 port 439 already exported
2015-01-01 00:00:16 port 454 already exported
2015-01-01 00:00:16 port 440 already exported
2015-01-01 00:00:16 port 455 already exported
2015-01-01 00:00:16 port 441 already exported
2015-01-01 00:00:16 port 456 already exported
2015-01-01 00:00:16 port 438 already exported
2015-01-01 00:00:16 port 453 already exported
2015-01-01 00:00:16 port 446 already exported
2015-01-01 00:00:16 port 445 already exported
2015-01-01 00:00:16 Note: front fan is power on!
2015-01-01 00:00:16 Note: rear fan is power on!
2015-01-01 00:00:16 start the http log.
2015-01-01 00:00:16 httpListenThread start ret=0 2015-01-01 00:00:16 start listen on 6060 ... 2015-01-01 00:00:16 load machine BHB56902 conf
2015-01-01 00:00:16 machine : BHB56902
2015-01-01 00:00:16 get test_loop_securely_find_asic_num failed
2015-01-01 00:00:16 get high_temp_sub_freq failed,set default high_temp_sub_freq = 10
2015-01-01 00:00:16 abandon mix board!
2015-01-01 00:00:16 get mix boardname[0][BHB56902], name:BHB56902 2015-01-01 00:00:16 bad chain id = 3
2015-01-01 00:00:19 bad chain id = 3
2015-01-01 00:00:21 power off
2015-01-01 00:00:23 ==========================capability start==========================
2015-01-01 00:00:23 board num = 3
2015-01-01 00:00:23 board id = 0, chain num = 1
2015-01-01 00:00:23 chain id = 0
2015-01-01 00:00:23 board id = 1, chain num = 1
2015-01-01 00:00:23 chain id = 1
2015-01-01 00:00:23 board id = 2, chain num = 1
2015-01-01 00:00:23 chain id = 2
2015-01-01 00:00:23 ==========================capability end============================
2015-01-01 00:00:23 chain num = 3 2015-01-01 00:00:26 load chain 0 eeprom data
2024-07-20 12:29:53 load chain 1 eeprom data
2024-07-20 12:29:57 load chain 2 eeprom data
2024-07-20 12:29:57 EEPROM error: CRC 3RD
2024-07-20 12:29:57 eeprom load ret:0 2024-07-20 12:29:57 miner:BHB56901,board_name:BHB56902 2024-07-20 12:29:57 miner:BHB56902,board_name:BHB56902 2024-07-20 12:29:57 create thread get_nonce_and_register_thread
2024-07-20 12:29:57 fixed working voltage = 1410
2024-07-20 12:29:57 Chain [0] PCB Version: 0x0300
2024-07-20 12:29:57 Chain [0] BOM Version: 0x0000
2024-07-20 12:29:57 Chain [1] PCB Version: 0x0300
2024-07-20 12:29:57 Chain [1] BOM Version: 0x0000
2024-07-20 12:29:57 Chain [2] PCB Version: 0x0300
2024-07-20 12:29:57 Chain [2] BOM Version: 0x0000
2024-07-20 12:29:57 bad chain id = 3
2024-07-20 12:29:57 Fan check passed.
2024-07-20 12:29:57 init fan pid target=60 2024-07-20 12:29:57 max sensor num = 4 2024-07-20 12:29:57 STATUS_INITED: soc init done!
2024-07-20 12:29:57 temperature_monitor_thread start... 2024-07-20 12:30:00 start to init...
2024-07-20 12:30:00 i2c_sim_init start
2024-07-20 12:30:00 init gpio477
2024-07-20 12:30:00 init gpio476
2024-07-20 12:30:00 i2c_sim_init end
2024-07-20 12:30:01 power open power_version = 0x76
2024-07-20 12:30:05 power is Calibrated
2024-07-20 12:30:05 power sn:DGQG329BCAJJG1015
2024-07-20 12:30:05 enable_power_calibration,calibration date:211208.
2024-07-20 12:30:07 power type version: 0x0076
2024-07-20 12:30:09 disable power watchdog: 0x0000
2024-07-20 12:30:10 Initializing the power, please wait, this may take up to 2 minutes...
2024-07-20 12:31:30 Slept 80 seconds, diff = 1.
2024-07-20 12:31:40 set_voltage_by_steps to 1300.
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 set_voltage_by_steps to 1500.
2024-07-20 12:31:49 start up min temp by 75a = 31 2024-07-20 12:31:51 Chain[0]: find 77 asic, times 0
2024-07-20 12:31:53 Chain[1]: find 77 asic, times 0
2024-07-20 12:31:55 Chain[2]: find 0 asic, times 0
2024-07-20 12:31:57 Chain[2]: find 0 asic, times 1
2024-07-20 12:31:58 Chain[2]: find 0 asic, times 2
2024-07-20 12:31:58 Chain 2 only find 0 asic, will power off hash board 2
2024-07-20 12:31:58 ERROR_SOC_INIT: soc init failed!
2024-07-20 12:31:58 stop_mining: soc init failed!
2024-07-20 12:31:58 uninit_temp_info 2024-07-20 12:31:58 do not read temp anymore... 2024-07-20 12:31:58 cancel thread
2024-07-20 12:31:58 ****power off hashboard****
2024-07-20 12:31:58 power off
2024-07-20 12:31:59 temp monitor thread exit 2024-07-20 12:32:25 Version num 65536
2024-07-20 12:32:25 Mask num 0x1fffe000
2024-07-20 12:32:25 Note: addrInterval or corenum is not initialized.
Title: Re: S19KPRO SINGLE HASHBOAD NOT MINING.
Post by: philipma1957 on July 22, 2024, 08:25:15 PM
This is my miner log Anyone please 2015-01-01 00:00:16 This is fix-freq version
2015-01-01 00:00:16 Miner compile time: Wed Nov 15 14:47:56 CST 2023 type: Antminer S19k Pro
2015-01-01 00:00:16 commit version: 143b498a 2023-11-09 14:37:23, build by: jenkins 2023-11-15 15:11:08
2015-01-01 00:00:16 opt_multi_version = 1
2015-01-01 00:00:16 opt_bitmain_ab = 1
2015-01-01 00:00:16 mid_auto_gen = 1
2015-01-01 00:00:16 opt_bitmain_work_mode = 2
2015-01-01 00:00:16 port 439 already exported
2015-01-01 00:00:16 port 454 already exported
2015-01-01 00:00:16 port 440 already exported
2015-01-01 00:00:16 port 455 already exported
2015-01-01 00:00:16 port 441 already exported
2015-01-01 00:00:16 port 456 already exported
2015-01-01 00:00:16 port 438 already exported
2015-01-01 00:00:16 port 453 already exported
2015-01-01 00:00:16 port 446 already exported
2015-01-01 00:00:16 port 445 already exported
2015-01-01 00:00:16 Note: front fan is power on!
2015-01-01 00:00:16 Note: rear fan is power on!
2015-01-01 00:00:16 start the http log.
2015-01-01 00:00:16 httpListenThread start ret=0 2015-01-01 00:00:16 start listen on 6060 ... 2015-01-01 00:00:16 load machine BHB56902 conf
2015-01-01 00:00:16 machine : BHB56902
2015-01-01 00:00:16 get test_loop_securely_find_asic_num failed
2015-01-01 00:00:16 get high_temp_sub_freq failed,set default high_temp_sub_freq = 10
2015-01-01 00:00:16 abandon mix board!
2015-01-01 00:00:16 get mix boardname[0][BHB56902], name:BHB56902 2015-01-01 00:00:16 bad chain id = 3
2015-01-01 00:00:19 bad chain id = 3
2015-01-01 00:00:21 power off
2015-01-01 00:00:23 ==========================capability start==========================
2015-01-01 00:00:23 board num = 3
2015-01-01 00:00:23 board id = 0, chain num = 1
2015-01-01 00:00:23 chain id = 0
2015-01-01 00:00:23 board id = 1, chain num = 1
2015-01-01 00:00:23 chain id = 1
2015-01-01 00:00:23 board id = 2, chain num = 1
2015-01-01 00:00:23 chain id = 2
2015-01-01 00:00:23 ==========================capability end============================
2015-01-01 00:00:23 chain num = 3 2015-01-01 00:00:26 load chain 0 eeprom data
2024-07-20 12:29:53 load chain 1 eeprom data
2024-07-20 12:29:57 load chain 2 eeprom data
2024-07-20 12:29:57 EEPROM error: CRC 3RD
2024-07-20 12:29:57 eeprom load ret:0 2024-07-20 12:29:57 miner:BHB56901,board_name:BHB56902 2024-07-20 12:29:57 miner:BHB56902,board_name:BHB56902 2024-07-20 12:29:57 create thread get_nonce_and_register_thread
2024-07-20 12:29:57 fixed working voltage = 1410
2024-07-20 12:29:57 Chain [0] PCB Version: 0x0300
2024-07-20 12:29:57 Chain [0] BOM Version: 0x0000
2024-07-20 12:29:57 Chain [1] PCB Version: 0x0300
2024-07-20 12:29:57 Chain [1] BOM Version: 0x0000
2024-07-20 12:29:57 Chain [2] PCB Version: 0x0300
2024-07-20 12:29:57 Chain [2] BOM Version: 0x0000
2024-07-20 12:29:57 bad chain id = 3
2024-07-20 12:29:57 Fan check passed.
2024-07-20 12:29:57 init fan pid target=60 2024-07-20 12:29:57 max sensor num = 4 2024-07-20 12:29:57 STATUS_INITED: soc init done!
2024-07-20 12:29:57 temperature_monitor_thread start... 2024-07-20 12:30:00 start to init...
2024-07-20 12:30:00 i2c_sim_init start
2024-07-20 12:30:00 init gpio477
2024-07-20 12:30:00 init gpio476
2024-07-20 12:30:00 i2c_sim_init end
2024-07-20 12:30:01 power open power_version = 0x76
2024-07-20 12:30:05 power is Calibrated
2024-07-20 12:30:05 power sn:DGQG329BCAJJG1015
2024-07-20 12:30:05 enable_power_calibration,calibration date:211208.
2024-07-20 12:30:07 power type version: 0x0076
2024-07-20 12:30:09 disable power watchdog: 0x0000
2024-07-20 12:30:10 Initializing the power, please wait, this may take up to 2 minutes...
2024-07-20 12:31:30 Slept 80 seconds, diff = 1.
2024-07-20 12:31:40 set_voltage_by_steps to 1300.
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 set_voltage_by_steps to 1500.
2024-07-20 12:31:49 start up min temp by 75a = 31 2024-07-20 12:31:51 Chain[0]: find 77 asic, times 0
2024-07-20 12:31:53 Chain[1]: find 77 asic, times 0
2024-07-20 12:31:55 Chain[2]: find 0 asic, times 0
2024-07-20 12:31:57 Chain[2]: find 0 asic, times 1
2024-07-20 12:31:58 Chain[2]: find 0 asic, times 2
2024-07-20 12:31:58 Chain 2 only find 0 asic, will power off hash board 2
2024-07-20 12:31:58 ERROR_SOC_INIT: soc init failed!
2024-07-20 12:31:58 stop_mining: soc init failed!
2024-07-20 12:31:58 uninit_temp_info 2024-07-20 12:31:58 do not read temp anymore... 2024-07-20 12:31:58 cancel thread
2024-07-20 12:31:58 ****power off hashboard****
2024-07-20 12:31:58 power off
2024-07-20 12:31:59 temp monitor thread exit 2024-07-20 12:32:25 Version num 65536
2024-07-20 12:32:25 Mask num 0x1fffe000
2024-07-20 12:32:25 Note: addrInterval or corenum is not initialized.
you have a dead board. try running braiins software and two boards. I would tell you buy an epic controller from altairtech.io https://altairtech.io/product/epic-umc/ but it is costly to do that. like $150 epic controller will run 2 boards. you could replace the control board to hashboard communication wire. https://altairtech.io/product/antminer-ribbon-cable/ you could reseat the one not working. likely fix is either braiins and run two boards or epic and two boards. a score is reseat the 18 pin ribbon and it works as that is free.
Title: Re: S19KPRO SINGLE HASHBOAD NOT MINING.
Post by: irfan655 on July 23, 2024, 07:59:38 AM
This is my miner log Anyone please 2015-01-01 00:00:16 This is fix-freq version
2015-01-01 00:00:16 Miner compile time: Wed Nov 15 14:47:56 CST 2023 type: Antminer S19k Pro
2015-01-01 00:00:16 commit version: 143b498a 2023-11-09 14:37:23, build by: jenkins 2023-11-15 15:11:08
2015-01-01 00:00:16 opt_multi_version = 1
2015-01-01 00:00:16 opt_bitmain_ab = 1
2015-01-01 00:00:16 mid_auto_gen = 1
2015-01-01 00:00:16 opt_bitmain_work_mode = 2
2015-01-01 00:00:16 port 439 already exported
2015-01-01 00:00:16 port 454 already exported
2015-01-01 00:00:16 port 440 already exported
2015-01-01 00:00:16 port 455 already exported
2015-01-01 00:00:16 port 441 already exported
2015-01-01 00:00:16 port 456 already exported
2015-01-01 00:00:16 port 438 already exported
2015-01-01 00:00:16 port 453 already exported
2015-01-01 00:00:16 port 446 already exported
2015-01-01 00:00:16 port 445 already exported
2015-01-01 00:00:16 Note: front fan is power on!
2015-01-01 00:00:16 Note: rear fan is power on!
2015-01-01 00:00:16 start the http log.
2015-01-01 00:00:16 httpListenThread start ret=0 2015-01-01 00:00:16 start listen on 6060 ... 2015-01-01 00:00:16 load machine BHB56902 conf
2015-01-01 00:00:16 machine : BHB56902
2015-01-01 00:00:16 get test_loop_securely_find_asic_num failed
2015-01-01 00:00:16 get high_temp_sub_freq failed,set default high_temp_sub_freq = 10
2015-01-01 00:00:16 abandon mix board!
2015-01-01 00:00:16 get mix boardname[0][BHB56902], name:BHB56902 2015-01-01 00:00:16 bad chain id = 3
2015-01-01 00:00:19 bad chain id = 3
2015-01-01 00:00:21 power off
2015-01-01 00:00:23 ==========================capability start==========================
2015-01-01 00:00:23 board num = 3
2015-01-01 00:00:23 board id = 0, chain num = 1
2015-01-01 00:00:23 chain id = 0
2015-01-01 00:00:23 board id = 1, chain num = 1
2015-01-01 00:00:23 chain id = 1
2015-01-01 00:00:23 board id = 2, chain num = 1
2015-01-01 00:00:23 chain id = 2
2015-01-01 00:00:23 ==========================capability end============================
2015-01-01 00:00:23 chain num = 3 2015-01-01 00:00:26 load chain 0 eeprom data
2024-07-20 12:29:53 load chain 1 eeprom data
2024-07-20 12:29:57 load chain 2 eeprom data
2024-07-20 12:29:57 EEPROM error: CRC 3RD
2024-07-20 12:29:57 eeprom load ret:0 2024-07-20 12:29:57 miner:BHB56901,board_name:BHB56902 2024-07-20 12:29:57 miner:BHB56902,board_name:BHB56902 2024-07-20 12:29:57 create thread get_nonce_and_register_thread
2024-07-20 12:29:57 fixed working voltage = 1410
2024-07-20 12:29:57 Chain [0] PCB Version: 0x0300
2024-07-20 12:29:57 Chain [0] BOM Version: 0x0000
2024-07-20 12:29:57 Chain [1] PCB Version: 0x0300
2024-07-20 12:29:57 Chain [1] BOM Version: 0x0000
2024-07-20 12:29:57 Chain [2] PCB Version: 0x0300
2024-07-20 12:29:57 Chain [2] BOM Version: 0x0000
2024-07-20 12:29:57 bad chain id = 3
2024-07-20 12:29:57 Fan check passed.
2024-07-20 12:29:57 init fan pid target=60 2024-07-20 12:29:57 max sensor num = 4 2024-07-20 12:29:57 STATUS_INITED: soc init done!
2024-07-20 12:29:57 temperature_monitor_thread start... 2024-07-20 12:30:00 start to init...
2024-07-20 12:30:00 i2c_sim_init start
2024-07-20 12:30:00 init gpio477
2024-07-20 12:30:00 init gpio476
2024-07-20 12:30:00 i2c_sim_init end
2024-07-20 12:30:01 power open power_version = 0x76
2024-07-20 12:30:05 power is Calibrated
2024-07-20 12:30:05 power sn:DGQG329BCAJJG1015
2024-07-20 12:30:05 enable_power_calibration,calibration date:211208.
2024-07-20 12:30:07 power type version: 0x0076
2024-07-20 12:30:09 disable power watchdog: 0x0000
2024-07-20 12:30:10 Initializing the power, please wait, this may take up to 2 minutes...
2024-07-20 12:31:30 Slept 80 seconds, diff = 1.
2024-07-20 12:31:40 set_voltage_by_steps to 1300.
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 bad chain id = 3
2024-07-20 12:31:42 set_voltage_by_steps to 1500.
2024-07-20 12:31:49 start up min temp by 75a = 31 2024-07-20 12:31:51 Chain[0]: find 77 asic, times 0
2024-07-20 12:31:53 Chain[1]: find 77 asic, times 0
2024-07-20 12:31:55 Chain[2]: find 0 asic, times 0
2024-07-20 12:31:57 Chain[2]: find 0 asic, times 1
2024-07-20 12:31:58 Chain[2]: find 0 asic, times 2
2024-07-20 12:31:58 Chain 2 only find 0 asic, will power off hash board 2
2024-07-20 12:31:58 ERROR_SOC_INIT: soc init failed!
2024-07-20 12:31:58 stop_mining: soc init failed!
2024-07-20 12:31:58 uninit_temp_info 2024-07-20 12:31:58 do not read temp anymore... 2024-07-20 12:31:58 cancel thread
2024-07-20 12:31:58 ****power off hashboard****
2024-07-20 12:31:58 power off
2024-07-20 12:31:59 temp monitor thread exit 2024-07-20 12:32:25 Version num 65536
2024-07-20 12:32:25 Mask num 0x1fffe000
2024-07-20 12:32:25 Note: addrInterval or corenum is not initialized.
you have a dead board. try running braiins software and two boards. I would tell you buy an epic controller from altairtech.io https://altairtech.io/product/epic-umc/ but it is costly to do that. like $150 epic controller will run 2 boards. you could replace the control board to hashboard communication wire. https://altairtech.io/product/antminer-ribbon-cable/ you could reseat the one not working. likely fix is either braiins and run two boards or epic and two boards. a score is reseat the 18 pin ribbon and it works as that is free. Sir i’ve tried the HiveOs two of my boards are working(Hashing) the last one is still not finding the chips i guess.. I replaced control board with one of my other s19kpro even swapped the cables too.. but still the hashboard not working. What kind of error is this In log i saw EEProm error still don’t understand. Thanks for your reply sir
Title: Re: S19KPRO SINGLE HASHBOAD NOT MINING.
Post by: BitMaxz on July 23, 2024, 08:21:48 PM
Sir i’ve tried the HiveOs two of my boards are working(Hashing) the last one is still not finding the chips i guess.. I replaced control board with one of my other s19kpro even swapped the cables too.. but still the hashboard not working. What kind of error is this In log i saw an EEProm error still don’t understand. Thanks for your reply sir
Since the first error said it's a mixed board then it's pointing to EEPROM and maybe the one hashboard is replaced. Did you buy it used unit? Since you switch to another OS I don't think you still need to bother EEPROM error unless you want to stay using stock firmware? If you want to stay using the stock firmware you might need to use the hashboard code editor to fix that issue but it won't fix the other hashboard with 0 ASIC. 0 ASIC error is a hardware issue it needs to be replaced if you want to run the unit with 3 hashboard or like others do try to reflow all components on the broken hashboard with BGA hot air or put it on the oven but the chances to fix 0 ASIC issue is 50/50.
Title: Re: S19KPRO SINGLE HASHBOAD NOT MINING.
Post by: philipma1957 on July 23, 2024, 08:54:09 PM
okay lets start from scratch. You switched cables and no go. not a cable issue. You put in a working bitmain controller and no go. not a bitmain controller issue. So here is the issue the 1 board is dead is maybe or the one board is mismatched and reads as dead. maybe if it all worked fine for a while it is very likely the board died and is read as a mismatch. bitmain firmware says fuck you all 3 run or we shut your ass down. If you only want to run bitmain firmware if may mean you need to repair or reprogram the dead board. But if you are willing to use after market products like braiins or epic both will allow you to run only 2 boards. https://altairtech.io/product/epic-umc/. the board is not cheap but you never pay a fee for it once you hook it up look at my gear all 3 boards are on. In your case you shut the dead on off and get 2 of 3 boards to work https://www.talkimg.com/images/2024/07/23/4j8Hg.png
Title: Re: S19KPRO SINGLE HASHBOAD NOT MINING.
Post by: irfan655 on July 23, 2024, 09:35:48 PM
Sir i’ve tried the HiveOs two of my boards are working(Hashing) the last one is still not finding the chips i guess.. I replaced control board with one of my other s19kpro even swapped the cables too.. but still the hashboard not working. What kind of error is this In log i saw an EEProm error still don’t understand. Thanks for your reply sir
Since the first error said it's a mixed board then it's pointing to EEPROM and maybe the one hashboard is replaced. Did you buy it used unit? Since you switch to another OS I don't think you still need to bother EEPROM error unless you want to stay using stock firmware? If you want to stay using the stock firmware you might need to use the hashboard code editor to fix that issue but it won't fix the other hashboard with 0 ASIC. 0 ASIC error is a hardware issue it needs to be replaced if you want to run the unit with 3 hashboard or like others do try to reflow all components on the broken hashboard with BGA hot air or put it on the oven but the chances to fix 0 ASIC issue is 50/50. Yes i bought this used from local market it was working fine from the past few weeks.. I have the chinese hashboard code editor can i give a try ? The last part of your message is hard for me to understand can you please explain more i’m new to these miner thing .. Thanks for your time sir
|