|
Title: Antminer S1 monitor via snmp/syslog Post by: wurzelsepp82 on April 08, 2014, 03:28:27 PM Hi all,
is there any way to monitor a Antminer S1 via snmp/syslog. im trying to get the temperature from the Unit. Thx all Wurzelsepp Title: Re: Antminer S1 monitor via snmp/syslog Post by: jimrome on April 08, 2014, 04:59:44 PM Hi all, is there any way to monitor a Antminer S1 via snmp/syslog. im trying to get the temperature from the Unit. Thx all Wurzelsepp The cgminer API is currently best way to do this. Syslog capability is present, but is a little broken and useful more for debugging functionality. I'm not sure that snmp is supported in any fashion. Title: Re: Antminer S1 monitor via snmp/syslog Post by: wurzelsepp82 on April 08, 2014, 05:42:00 PM Any manual for that? Im a noob and dont know anything about API
Title: Re: Antminer S1 monitor via snmp/syslog Post by: jimrome on April 08, 2014, 07:04:39 PM Any manual for that? Im a noob and dont know anything about API The manual: https://github.com/ckolivas/cgminer/blob/master/API-README You're going to want coffee before reading that. There's also this thread which might help: https://bitcointalk.org/index.php?topic=412322.msg5724869#msg5724869 Title: Re: Antminer S1 monitor via snmp/syslog Post by: wurzelsepp82 on April 08, 2014, 07:13:39 PM ok...for this i need more than 1 coffee!!!!
is there no other way to monitor antīs temperature??? im running the units in a serverroom and cant watch them 24/7 ... Title: Re: Antminer S1 monitor via snmp/syslog Post by: faxfan2002 on April 08, 2014, 07:27:21 PM You can use CGremote which gives an overview including temp (hooks into the API)
Title: Re: Antminer S1 monitor via snmp/syslog Post by: salfter on April 08, 2014, 07:29:08 PM ok...for this i need more than 1 coffee!!!! is there no other way to monitor antīs temperature??? im running the units in a serverroom and cant watch them 24/7 ... AFAIK, no. Once you have API access enabled (https://bitcointalk.org/index.php?topic=499837.msg5528530#msg5528530), you could use something like MobileMiner (http://www.mobileminerapp.com/) to check on your miners from anywhere. Mine are in the garage...they usually run around 115-120°F. Title: Re: Antminer S1 monitor via snmp/syslog Post by: jimrome on April 08, 2014, 10:53:59 PM ok...for this i need more than 1 coffee!!!! is there no other way to monitor antīs temperature??? im running the units in a serverroom and cant watch them 24/7 ... You're aware there's a web UI? Temp data can be seen in the 'miner status' tab. Title: Re: Antminer S1 monitor via snmp/syslog Post by: wurzelsepp82 on April 09, 2014, 07:16:04 AM Quote You're aware there's a web UI? Temp data can be seen in the 'miner status' tab. But i dont want to open 7 Webinterfaces for checking temperature. And i want to get notification if the temperature reaches a critical level. Title: Re: Antminer S1 monitor via snmp/syslog Post by: digitizing on April 09, 2014, 08:41:33 AM Quote You're aware there's a web UI? Temp data can be seen in the 'miner status' tab. But i dont want to open 7 Webinterfaces for checking temperature. And i want to get notification if the temperature reaches a critical level. and use this command in linux socat TCP4-LISTEN:4028,fork TCP4:192.168.1.99:4028 because cgminermonitor can only access to cgminer that running in the same machine Title: Re: Antminer S1 monitor via snmp/syslog Post by: wurzelsepp82 on April 09, 2014, 06:46:11 PM ok cgremote doing a good job but there is no notification system for temperature reaches critical level.
and really big problem is --> if temperature goes critical the ant should shutdown nobody else have this problems? nobody afraid of burning down your serverroom or house? Title: Re: Antminer S1 monitor via snmp/syslog Post by: jimrome on April 10, 2014, 07:05:00 PM ok cgremote doing a good job but there is no notification system for temperature reaches critical level. and really big problem is --> if temperature goes critical the ant should shutdown nobody else have this problems? nobody afraid of burning down your serverroom or house? Very much so, and I fought with the S1's thermal management (or lack thereof) for quite a while. Then Kano released custom cgminer binaries for the S1 that actually allow for a user specified temp threshold after which the miner goes into a cooldown mode (with a lower hashrate). You can find them here: https://github.com/kanoi/cgminer-binaries/tree/master/AntS1 Title: Re: Antminer S1 monitor via snmp/syslog Post by: wurzelsepp82 on April 10, 2014, 07:36:18 PM thx fot that, but i cant get it to run ...
cgminer doesnt start Title: Re: Antminer S1 monitor via snmp/syslog Post by: lowerjerzey on April 11, 2014, 05:16:51 AM I wrote this in java with Selenium. Only 11 lines. I can add a temp check so if it exceeds a certain temp, it will automatically ssh in and kill cgminer, sleep for a set amount of time to cooldown(I think once cgminer is killed the webpage won't have the temp so I can't monitor if it cooled down), soft link in an asic-freq with the min frequency, then reboot. I'll have to add JSCH so it can ssh in. I can slap a gui on it and add the ability to monitor multiple antminers. The cgminer API is clunky and requires cgminer config file modification which a lot of owners probably won't feel comfortable to mess with. Plus, after reading that enabling the api may have caused dead chips, I don't want to touch it.
https://i.imgur.com/RHA0wON.jpg Title: Re: Antminer S1 monitor via snmp/syslog Post by: wolf_miner on April 11, 2014, 06:15:08 AM ....... WHAT......? ??? enabling API may caused dead chips? Where you find this?
W_M Title: Re: Antminer S1 monitor via snmp/syslog Post by: jimrome on April 11, 2014, 06:18:54 AM ....... WHAT......? ??? enabling API may caused dead chips? Where you find this? W_M Complete bullshit until proven otherwise. Title: Re: Antminer S1 monitor via snmp/syslog Post by: lowerjerzey on April 13, 2014, 02:06:35 AM ....... WHAT......? ??? enabling API may caused dead chips? Where you find this? W_M Complete bullshit until proven otherwise. https://bitcointalk.org/index.php?topic=412322.msg5072840#msg5072840 Not an unreasonable claim. I've gotten dead chips from simply rebooting. I've had to unplug the antminer and plug it back in to resolve them. Title: Re: Antminer S1 monitor via snmp/syslog Post by: wolf_miner on April 13, 2014, 11:06:19 AM Hi, API are active on Antminer S1, infact if you connect to console ad run the command cgminer-api summary there is an answer like this
Code: root@antMiner:~# cgminer-api summary but is not allowed to call API from another computer else localhost (127.0.0.1) because in the configuration there aren't all necessary permission. So you need to enable the API for remote access. Someone suggest to edit /etc/config/cgminer. I do not know what solution is correct, but I think it is to edit /etc/init.d/cgminer because the etc/config/cgminer is written directly by Luci interface. W_M[/code] Title: Re: Antminer S1 monitor via snmp/syslog Post by: Slesh on April 13, 2014, 01:13:39 PM Use CGRemote - http://manotechnology.blogspot.cz/p/cgremote.html - it gives you all you need for mining.
Great SW for monitoring. Title: Re: Antminer S1 monitor via snmp/syslog Post by: Slesh on April 13, 2014, 01:18:11 PM Hi, API are active on Antminer S1, infact if you connect to console ad run the command cgminer-api summary there is an answer like this Code: root@antMiner:~# cgminer-api summary but is not allowed to call API from another computer else localhost (127.0.0.1) because in the configuration there aren't all necessary permission. So you need to enable the API for remote access. Someone suggest to edit /etc/config/cgminer. I do not know what solution is correct, but I think it is to edit /etc/init.d/cgminer because the etc/config/cgminer is written directly by Luci interface. W_M[/code] Go to S1 config - /etc/config/cgminer Set: option api-listen option api_allow 'W:127.0.0.1,10.0.0.XX' (10.0.0.XX) is IP of the computer where you want to monitor S1. Title: Re: Antminer S1 monitor via snmp/syslog Post by: jimrome on April 14, 2014, 05:11:48 AM ....... WHAT......? ??? enabling API may caused dead chips? Where you find this? W_M Complete bullshit until proven otherwise. https://bitcointalk.org/index.php?topic=412322.msg5072840#msg5072840 Not an unreasonable claim. I've gotten dead chips from simply rebooting. I've had to unplug the antminer and plug it back in to resolve them. I disagree, and still call bullshit. Unless there is some other underlying issue (software corruption?) simply enabling the API shouldn't cause "dead chips". Title: Re: Antminer S1 monitor via snmp/syslog Post by: jimrome on April 14, 2014, 05:18:11 AM Hi, API are active on Antminer S1, infact if you connect to console ad run the command cgminer-api summary there is an answer like this <snip> but is not allowed to call API from another computer else localhost (127.0.0.1) because in the configuration there aren't all necessary permission. So you need to enable the API for remote access. Someone suggest to edit /etc/config/cgminer. I do not know what solution is correct, but I think it is to edit /etc/init.d/cgminer because the etc/config/cgminer is written directly by Luci interface. W_M I think the 'correct' way would be to edit the /etc/config/cgminer config file - you'll see that /etc/config/init.d actually pulls values from it as well. Doesn't really matter I suppose as long as the values are properly passed onto cgminer upon launch. Title: Re: Antminer S1 monitor via snmp/syslog Post by: criggie on July 14, 2014, 02:52:08 AM is there any way to monitor a Antminer S1 via snmp/syslog. im trying to get the temperature from the Unit. Yes - I've just done this. 1) log into GUI and go to System --> Software --> [ Update lists ] then wait a bit 2) Under Status, click the /Available Packages\ tab then click the /S\ tab 3) Scroll down to snmpd and click install. You can ignore the snmpd-static and snmpd-utils packages. 4) SSH to your miner and log in as root 5) vi /etc/snmp/snmpd.conf and set it like this rocommunity Waizphzbp3 exec minerstatus1 /bin/sh /root/cgminer-api-summary 6) vi /root/cgminer-api-summary and set the contents like this /usr/bin/cgminer-api stats | egrep "temp|fan" | grep -v "Reply was" | tr -d " []><()" | tr "=" ":" /usr/bin/cgminer-api coin | egrep "Time|Difficulty" | grep -v "Reply was" | tr -d " []><()" | tr "=" ":" 7) Back to the web gui, go to System --> Startup and "enable snmpd" then click the start button for snmpd. 8) FAIL This is the bit I haven't done yet. My miner is not publicly accessible, so I simply disabled its firewall. If you have an uncontrolled environment, you want to permit port 161 UDP from the monitoring host only. 9) To scan it I did this on my remote host. snmpwalk -Os -c Waizphzbp3 -v 2c 192.168.1.93 .1.3.6.1.4.1.2021.8 which returns this output: extIndex.1 = INTEGER: 1 extNames.1 = STRING: minerstatus1 extCommand.1 = STRING: /bin/sh /root/cgminer-api-summary extResult.1 = INTEGER: 0 extOutput.1 = STRING: fan_num:1 fan1:2820 fan2:0 fan3:0 fan4:0 temp_num:2 temp1:41 temp2:44 temp3:0 temp4:0 temp_avg:42 temp_max:45 temp_hi:44 overheat_temp:0 opt_bitmain_temp:50 opt_bitmain_fan_min:32 opt_bitmain_fan_max:160 PoolAttempts:0 CurrentBlockTime:1405304337.011621 NetworkDifficulty:17336316978.50783100 extErrFix.1 = INTEGER: noError(0) extErrFixCmd.1 = STRING: So my S1 is at 41 and 44 degrees C, with the front fan doing 2820 RPM . My rear fan is only 3 wire and doesn't report speeds. To customise, simply edit the shell script in /root/cgminer-api-summary to suit your needs. There are a heap of different options that cgminer-api takes, the shell script simply formats them. Some of the ones I've looks at: /usr/bin/cgminer-api devs Info on attached asics /usr/bin/cgminer-api pools Info on pools /usr/bin/cgminer-api switchpool Change to another configured pool /usr/bin/cgminer-api notify unsure /usr/bin/cgminer-api devdetails device info, more details /usr/bin/cgminer-api stats /usr/bin/cgminer-api summary /usr/bin/cgminer-api config failover info /usr/bin/cgminer-api coin stats about current block and difficulty /usr/bin/cgminer-api usbstats Lots of stuff /usr/bin/cgminer-api zero reset counters ? /usr/bin/cgminer-api hotplug ? /usr/bin/cgminer-api ascset configure asics on the fly /usr/bin/cgminer-api asccount count attached asics /usr/bin/cgminer-api lockstats dunno - not compiled /usr/bin/cgminer-api edevs devs but for devices that are enabled only /usr/bin/cgminer-api estats stats but for enabled devices only. /usr/bin/cgminer-api lcd One liner? Not compiled in Any questions please ask, and if you have fiddled your firewall please let us know the clean tidy way to do that. Title: Re: Antminer S1 monitor via snmp/syslog Post by: Pjones on July 15, 2014, 05:56:07 AM https://github.com/mdude77/MAntMonitor
It does what you need. Title: Re: Antminer S1 monitor via snmp/syslog Post by: btcfade on December 01, 2014, 11:07:31 AM Mine doesn't work I guess. I just filled in the IP under GUI SYSTEM/SYSTEM/LOGGING. My log server never shows anything. Is there something else besides this you have to do?
Title: Re: Antminer S1 monitor via snmp/syslog Post by: btcfade on December 01, 2014, 12:08:46 PM nevermind, adding api-listen worked.. thanks for all the great help..
Title: Re: Antminer S1 monitor via snmp/syslog Post by: btcfade on December 01, 2014, 01:55:03 PM it's logging to 514 syslog .. i'm gonna have to wait for it to crash again to see if it says anything other than /usr/bin/cgminer-monitor..
anybody know what i'm saying? Title: Re: Antminer S1 monitor via snmp/syslog Post by: btcfade on December 01, 2014, 02:27:51 PM is there any way to monitor a Antminer S1 via snmp/syslog. im trying to get the temperature from the Unit. Yes - I've just done this. 1) log into GUI and go to System --> Software --> [ Update lists ] then wait a bit 2) Under Status, click the /Available Packages\ tab then click the /S\ tab 3) Scroll down to snmpd and click install. You can ignore the snmpd-static and snmpd-utils packages. 4) SSH to your miner and log in as root 5) vi /etc/snmp/snmpd.conf and set it like this rocommunity Waizphzbp3 exec minerstatus1 /bin/sh /root/cgminer-api-summary 6) vi /root/cgminer-api-summary and set the contents like this /usr/bin/cgminer-api stats | egrep "temp|fan" | grep -v "Reply was" | tr -d " []><()" | tr "=" ":" /usr/bin/cgminer-api coin | egrep "Time|Difficulty" | grep -v "Reply was" | tr -d " []><()" | tr "=" ":" 7) Back to the web gui, go to System --> Startup and "enable snmpd" then click the start button for snmpd. 8) FAIL This is the bit I haven't done yet. My miner is not publicly accessible, so I simply disabled its firewall. If you have an uncontrolled environment, you want to permit port 161 UDP from the monitoring host only. 9) To scan it I did this on my remote host. snmpwalk -Os -c Waizphzbp3 -v 2c 192.168.1.93 .1.3.6.1.4.1.2021.8 which returns this output: extIndex.1 = INTEGER: 1 extNames.1 = STRING: minerstatus1 extCommand.1 = STRING: /bin/sh /root/cgminer-api-summary extResult.1 = INTEGER: 0 extOutput.1 = STRING: fan_num:1 fan1:2820 fan2:0 fan3:0 fan4:0 temp_num:2 temp1:41 temp2:44 temp3:0 temp4:0 temp_avg:42 temp_max:45 temp_hi:44 overheat_temp:0 opt_bitmain_temp:50 opt_bitmain_fan_min:32 opt_bitmain_fan_max:160 PoolAttempts:0 CurrentBlockTime:1405304337.011621 NetworkDifficulty:17336316978.50783100 extErrFix.1 = INTEGER: noError(0) extErrFixCmd.1 = STRING: So my S1 is at 41 and 44 degrees C, with the front fan doing 2820 RPM . My rear fan is only 3 wire and doesn't report speeds. To customise, simply edit the shell script in /root/cgminer-api-summary to suit your needs. There are a heap of different options that cgminer-api takes, the shell script simply formats them. Some of the ones I've looks at: /usr/bin/cgminer-api devs Info on attached asics /usr/bin/cgminer-api pools Info on pools /usr/bin/cgminer-api switchpool Change to another configured pool /usr/bin/cgminer-api notify unsure /usr/bin/cgminer-api devdetails device info, more details /usr/bin/cgminer-api stats /usr/bin/cgminer-api summary /usr/bin/cgminer-api config failover info /usr/bin/cgminer-api coin stats about current block and difficulty /usr/bin/cgminer-api usbstats Lots of stuff /usr/bin/cgminer-api zero reset counters ? /usr/bin/cgminer-api hotplug ? /usr/bin/cgminer-api ascset configure asics on the fly /usr/bin/cgminer-api asccount count attached asics /usr/bin/cgminer-api lockstats dunno - not compiled /usr/bin/cgminer-api edevs devs but for devices that are enabled only /usr/bin/cgminer-api estats stats but for enabled devices only. /usr/bin/cgminer-api lcd One liner? Not compiled in Any questions please ask, and if you have fiddled your firewall please let us know the clean tidy way to do that. how can i do this without downloading snmp? i mean i already got talking to the server, do i have to send it commands? can it just send updates to the syslog? Title: Re: Antminer S1 monitor via snmp/syslog Post by: criggie on December 01, 2014, 07:27:40 PM how can i do this without downloading snmp? i mean i already got talking to the server, do i have to send it commands? can it just send updates to the syslog? Well the commands given above will return you info on your miner when run at the command prompt. The SNMP stuff is just one way of running those commands remotely. You could easily use a command like ssh miner /usr/bin/cgminer-api stats And get the info that way. Good thing about SNMP is it already offers permissions and networking framework. I poll from Cacti which likes SNMP. |
