|
Title: antminer S1: connect via LAN, setup WWAN, but can't access via wifi Post by: domerdel on April 25, 2014, 02:04:11 AM I have my ant miner s1 in the other room. when i configure it, i use the LAN to put all the setup info in. I was able to get a static WAN IP on my network, and while tethered, I configured the WWAN. I set a static IP for that and before I unplugged it, I could see my router recognize it as a wireless device. I proceed to do a software reboot on the miner, wait 3-5 mins,
Title: Re: antminer S1: connect via LAN, setup WWAN, but can't access via wifi Post by: Meech on April 25, 2014, 02:41:04 AM Dont try using the wifi built in others have suggested adding a wifi bridge that seem to work. I don't know much about those settings but the lan is easy and these run like champs.
Title: Re: antminer S1: connect via LAN, setup WWAN, but can't access via wifi Post by: GaryL on April 25, 2014, 03:28:13 AM Go to network-firewall and try change some settings, but it's very difficult to do it,
I can manage it from wifi, but i don't know what i've done exactly ! Title: Re: antminer S1: connect via LAN, setup WWAN, but can't access via wifi Post by: GiLa on April 25, 2014, 08:54:14 AM I ran 2 s1 on wifi for over a week saw no difference in performance.
was experiencing drop outs initially but used a 30dbi high gain antenna and saw no difference between hardwired and wifi setting up wifi is quite easy once you have setup the lan side and got that working, then hit the wifi and scan add your wireless network in and that should be it. everything else should be configured on the WAN, and if you stuff it up, just hit the reset button and reconfigure. I will say the WRT module is bit slow so don't expect it to start hashing on wifi instantly it could take a good 5 minutes before starting. when adding wifi DO NOT change any the IP settings on wifi, that's all done on the wan not wifi section. Title: Re: antminer S1: connect via LAN, setup WWAN, but can't access via wifi Post by: domerdel on April 26, 2014, 03:28:38 AM I caved. I just drilled holes, climbed in the top crawl space and ran cat6 to the other room. My next problem is, it stops mining after 30 mins (beeping sound).
Chain 1 Fan 2220 Temp 39 Chain 2 Fan 0 Temp 42 I have a honeywell blowing air on it. I only have one mining pool set up. Title: Re: antminer S1: connect via LAN, setup WWAN, but can't access via wifi Post by: BoogieMan82 on April 26, 2014, 05:05:59 PM I caved. I just drilled holes, climbed in the top crawl space and ran cat6 to the other room. My next problem is, it stops mining after 30 mins (beeping sound). Chain 1 Fan 2220 Temp 39 Chain 2 Fan 0 Temp 42 I have a honeywell blowing air on it. I only have one mining pool set up. Beeping means it doesn't have an active internet connection. Title: Re: antminer S1: connect via LAN, setup WWAN, but can't access via wifi Post by: domerdel on April 28, 2014, 02:27:53 AM I caved. I just drilled holes, climbed in the top crawl space and ran cat6 to the other room. My next problem is, it stops mining after 30 mins (beeping sound). Chain 1 Fan 2220 Temp 39 Chain 2 Fan 0 Temp 42 I have a honeywell blowing air on it. I only have one mining pool set up. Beeping means it doesn't have an active internet connection. It's wired in. The only thing I have to solve it, is a reboot. Is there a way where I can schedule it to reboot every 3 or 4 hours? Title: Re: antminer S1: connect via LAN, setup WWAN, but can't access via wifi Post by: rotediablo on April 28, 2014, 03:41:41 AM see this thread to set S1's to auto reboot.
https://bitcointalk.org/index.php?topic=587268.0 |