Title: NEED HELP !!! ITS URGENT Post by: orangelemon on January 15, 2018, 12:06:57 PM PLEASE HELP!!!
ASROCK H81 PRO BTC R2.0 3x Sapphire Nitro RX 580 4GB INTEL G3420 Processor with 8GB RAM 120GB SSD NEW VERSION RISERS ANTEC 1300W 80Plus Platinum PSU. windows 10Pro 64bit Blockchain version Drivers Atidag patcher virtual memory increased CLAYMORE MINER DONE!! everything is setup and running pretty solid on stock setting. i flashed GPUs none by one and testing for 20 to 30 mins >> All fine i add 2nd GPU and did the same >> all fine i flashed my 3rd GPU bios and when mining getting start and trying to creat 3rd GPU's dag file, a blue screen appears saying" THREAD STUCK IN DEVICE DRIVER" and system restart. But when i upload original BIOS back to any of GPU, mining started without any problem and it ran more than 14hours until i repeat the same process but endup finding with same error " THREAD STUCK IN DEVICE DRIVER" and system restart. I did tried to update motherboad's bios but ASROCK H81 PROBTC R2.0 don't have latest BIOS as previous OLD H81 PRO BTC have. I tried to upgrade with H81 PRO BTC BIOS file versions from P1.30 to P2.30 but didn't detect by ASROCK H81 PRO BTC R2.0 PLEASE HELP ME!!! Title: Re: NEED HELP !!! ITS URGENT Post by: xxcsu on January 15, 2018, 12:29:34 PM so with the original bios your system is working fine , but with modded bios is crashing ?
Title: Re: NEED HELP !!! ITS URGENT Post by: orangelemon on January 15, 2018, 01:12:49 PM so with the original bios your system is working fine , but with modded bios is crashing ? Yes but with modded bios system mining perfectly with only two GPUs when I add 3rd gpu with modded bios system crashed with error "THREAD STRUCK IN DEVICE DRIVER" but when I reupload original BIOS to any GPUs, system mining perfectly with 3x GPUs without any single error Title: Re: NEED HELP !!! ITS URGENT Post by: mshordja on January 15, 2018, 01:15:55 PM PLEASE HELP!!! ASROCK H81 PRO BTC R2.0 3x Sapphire Nitro RX 580 4GB INTEL G3420 Processor with 8GB RAM 120GB SSD NEW VERSION RISERS ANTEC 1300W 80Plus Platinum PSU. windows 10Pro 64bit Blockchain version Drivers Atidag patcher virtual memory increased CLAYMORE MINER DONE!! everything is setup and running pretty solid on stock setting. i flashed GPUs none by one and testing for 20 to 30 mins >> All fine i add 2nd GPU and did the same >> all fine i flashed my 3rd GPU bios and when mining getting start and trying to creat 3rd GPU's dag file, a blue screen appears saying" THREAD STUCK IN DEVICE DRIVER" and system restart. But when i upload original BIOS back to any of GPU, mining started without any problem and it ran more than 14hours until i repeat the same process but endup finding with same error " THREAD STUCK IN DEVICE DRIVER" and system restart. I did tried to update motherboad's bios but ASROCK H81 PROBTC R2.0 don't have latest BIOS as previous OLD H81 PRO BTC have. I tried to upgrade with H81 PRO BTC BIOS file versions from P1.30 to P2.30 but didn't detect by ASROCK H81 PRO BTC R2.0 PLEASE HELP ME!!! there are several reason for the crash, what drivers are you using? overclocking downclocking are you using? Check the 3-rd riser is working alone, give some more info to analise? Title: Re: NEED HELP !!! ITS URGENT Post by: orangelemon on January 15, 2018, 01:30:54 PM PLEASE HELP!!! ASROCK H81 PRO BTC R2.0 3x Sapphire Nitro RX 580 4GB INTEL G3420 Processor with 8GB RAM 120GB SSD NEW VERSION RISERS ANTEC 1300W 80Plus Platinum PSU. windows 10Pro 64bit Blockchain version Drivers Atidag patcher virtual memory increased CLAYMORE MINER DONE!! everything is setup and running pretty solid on stock setting. i flashed GPUs none by one and testing for 20 to 30 mins >> All fine i add 2nd GPU and did the same >> all fine i flashed my 3rd GPU bios and when mining getting start and trying to creat 3rd GPU's dag file, a blue screen appears saying" THREAD STUCK IN DEVICE DRIVER" and system restart. But when i upload original BIOS back to any of GPU, mining started without any problem and it ran more than 14hours until i repeat the same process but endup finding with same error " THREAD STUCK IN DEVICE DRIVER" and system restart. I did tried to update motherboad's bios but ASROCK H81 PROBTC R2.0 don't have latest BIOS as previous OLD H81 PRO BTC have. I tried to upgrade with H81 PRO BTC BIOS file versions from P1.30 to P2.30 but didn't detect by ASROCK H81 PRO BTC R2.0 PLEASE HELP ME!!! there are several reason for the crash, what drivers are you using? overclocking downclocking are you using? Check the 3-rd riser is working alone, give some more info to analise? what drivers are you using? - Blockchain version of drivers overclocking downclocking are you using? - I flashed bios with bit over clocking -cclock 1150 -mclock 2050 -cvddc 900 -mvddc 900 Check the 3-rd riser is working alone - I replaced riser, swap the risers and also swap the cards..i have already described in OP Title: Re: NEED HELP !!! ITS URGENT Post by: mobomofo on January 15, 2018, 01:40:07 PM I got the thread stuck in device driver message...
Mine was due to the risers. First set only had 3 capacitors and 1 chip on the board and were powered via a MOLEX connector. On a whim I moved to boards with 4 caps and 2 chips (and a POT?) on the board with 6 pin power and everything was stable. Beat my head against a wall for 3 days on that one. Same issue, I could get two...sometimes 3 working, but when I tried to get cards 4 and 5 up, it would knock me back to only seeing 2 of the cards. YMMV My cards were stock. Non-Working Board https://sc01.alicdn.com/kf/HTB1OFP_SXXXXXX7aXXXq6xXFXXXx/4PIN-pcie-riser-1x-16x-molex-with.jpg_350x350.jpg Working Board https://images10.newegg.com/NeweggImage/ProductImageCompressAll1280/12-119-888-V02.jpg Title: Re: NEED HELP !!! ITS URGENT Post by: orangelemon on January 15, 2018, 01:46:02 PM I got the thread stuck in device driver message... Was using latest version risers, but they only had 3 capacitors and 1 chip on the board and were powered via a SATA connector. On a whim I moved to boards with 4 caps and 2 chips (and a POT?) on the board with 6 pin power and everything was stable. Beat my head against a wall for 3 days on that one. Same issue, I could get two...sometimes 3 working, but when I tried to get cards 4 and 5 up, it would knock me back to only seeing 2 of the cards. YMMV firstly I thought its risers fault, it was brandnew latest version risers but I changed with better one with big solid capacitor but getting same result. pls guys try to understand the actual fault. I think its motherboard's bios fault but I didn't find latest bios for H81 PRO BTC R2.0 board as older version of H81 PRO BTC have. I found this so far : https://bitcointalk.org/index.php?topic=1913747.msg23992468#msg23992468 Title: Re: NEED HELP !!! ITS URGENT Post by: mobomofo on January 15, 2018, 01:48:34 PM I got the thread stuck in device driver message... Was using latest version risers, but they only had 3 capacitors and 1 chip on the board and were powered via a SATA connector. On a whim I moved to boards with 4 caps and 2 chips (and a POT?) on the board with 6 pin power and everything was stable. Beat my head against a wall for 3 days on that one. Same issue, I could get two...sometimes 3 working, but when I tried to get cards 4 and 5 up, it would knock me back to only seeing 2 of the cards. YMMV firstly I thought its risers fault, it was brandnew latest version risers but I changed with better one with big solid capacitor but getting same result. pls guys try to understand the actual fault. I think its motherboard's bios fault but I didn't find latest bios for H81 PRO BTC R2.0 board as older version of H81 PRO BTC have. I updated my past post with pics of the boards I was using vs ones that I'm now using. Do yours look like the ones I'm using that work? Just a thought... Unfortunately I have no experience with the H81 so I cannot comment on that part - I use the ASUS B250 Expert and Dell T7500s. Title: Re: NEED HELP !!! ITS URGENT Post by: mobomofo on January 15, 2018, 01:56:33 PM Have you used DDU to remove all of the drivers and do a fresh driver install?
Title: Re: NEED HELP !!! ITS URGENT Post by: orangelemon on January 15, 2018, 03:05:21 PM Have you used DDU to remove all of the drivers and do a fresh driver install? Yes I did this aswell, same result Title: Re: NEED HELP !!! ITS URGENT Post by: xxcsu on January 15, 2018, 03:29:57 PM I think its motherboard's bios fault but I didn't find latest bios for H81 PRO BTC R2.0 board as older version of H81 PRO BTC have. I found this so far : https://bitcointalk.org/index.php?topic=1913747.msg23992468#msg23992468 can not be your motherboard bios , if your computer is mining fine with original vga bioses. THERE is the latest bios (http://www.asrock.com/mb/Intel/H81%20Pro%20BTC%20R2.0/#BIOS) for your motherboard Did you modded your own bios ? "stuck in device driver" - this error can be a reasult of a inproper overclocking . flash your bioses with only mem strap mod , then play with a frequency/voltage settings . Quote overclocking downclocking are you using? those voltages might be to low for your cards and working fine for somebody else cards :) every cards are different. What is the ASIC quality for your cards ?- I flashed bios with bit over clocking -cclock 1150 -mclock 2050 -cvddc 900 -mvddc 900 have you set the page file for 16GB or larger ? Title: Re: NEED HELP !!! ITS URGENT Post by: orangelemon on January 15, 2018, 03:43:58 PM I think its motherboard's bios fault but I didn't find latest bios for H81 PRO BTC R2.0 board as older version of H81 PRO BTC have. I found this so far : https://bitcointalk.org/index.php?topic=1913747.msg23992468#msg23992468 can not be your motherboard bios , if your computer is mining fine with original vga bioses. THERE is the latest bios (http://www.asrock.com/mb/Intel/H81%20Pro%20BTC%20R2.0/#BIOS) for your motherboard Did you modded your own bios ? "stuck in device driver" - this error can be a reasult of a inproper overclocking . flash your bioses with only mem strap mod , then play with a frequency/voltage settings . Quote overclocking downclocking are you using? those voltages might be to low for your cards and working fine for somebody else cards :) every cards are different. What is the ASIC quality for your cards ?- I flashed bios with bit over clocking -cclock 1150 -mclock 2050 -cvddc 900 -mvddc 900 have you set the page file for 16GB or larger ? Nope, i downloaded (not remembered) if this because of inproper over clocking then why it mining perfectly with two modded bios GPUs, why its getting problem only after adding up 3rd GPU with modded bios? EDIT : Might be inproper over clocking issue Yes i have set page file size larger than 16GB Title: Re: NEED HELP !!! ITS URGENT Post by: xxcsu on January 15, 2018, 03:53:55 PM if this because of inproper over clocking then why it mining perfectly with two modded bios GPUs, why its getting problem only after adding up 3rd GPU with modded bios? JUST LIKE I SAID EARLIER ... IF YOUR COMPUTER IS WORKING FINE WITH ORIGINAL BIOSES FLASHED BACK TO YOUR VGA CARDS , AND NOT WORKING , GIVE YOU ERRORS WITH FLASHED BIOS , YOUR MOTHERBOARD IS FINE. USE UR BRAIN : 3 CRADS ORIGINAL BIOS EVERYTHING FINE 3 CARDS MODDED BIOS ERRORS WHERE CAN BE A PROBLEM ??? I think you have no idea about how properly overclocking , undervolting your cards , modding your bios ... I think you se this numbers somewhere " -cclock 1150 -mclock 2050 -cvddc 900 -mvddc 900" that is why you using it , but you never fine tuned your cards ... You dowloaded the bios from the internet. The dowloaded bios version is the same as you had on all of your cards ? what bios version you originally have ? and what the bios version what you dowloaded ? WAHT IS THE ASIC QUALITY OF YOUR CARDS Title: Re: NEED HELP !!! ITS URGENT Post by: orangelemon on January 15, 2018, 04:13:14 PM if this because of inproper over clocking then why it mining perfectly with two modded bios GPUs, why its getting problem only after adding up 3rd GPU with modded bios? JUST LIKE I SAID EARLIER ... IF YOUR COMPUTER IS WORKING FINE WITH ORIGINAL BIOSES FLASHED BACK TO YOUR VGA CARDS , AND NOT WORKING , GIVE YOU ERRORS WITH FLASHED BIOS , YOUR MOTHERBOARD IS FINE. USE UR BRAIN : 3 CRADS ORIGINAL BIOS EVERYTHING FINE 3 CARDS MODDED BIOS ERRORS WHERE CAN BE A PROBLEM ??? I think you have no idea about how properly overclocking , undervolting your cards , modding your bios ... I think you se this numbers somewhere " -cclock 1150 -mclock 2050 -cvddc 900 -mvddc 900" that is why you using it , but you never fine tuned your cards ... You dowloaded the bios from the internet. The dowloaded bios version is the same as you had on all of your cards ? what bios version you originally have ? and what the bios version what you dowloaded ? WAHT IS THE ASIC QUALITY OF YOUR CARDS I got your point It is really a modded bios problem that I downloaded from internet. original bios is elpida Thank you so much for help and my brain is now working again ;D Title: Re: NEED HELP !!! ITS URGENT Post by: orangelemon on January 15, 2018, 06:08:03 PM Where I can find best modded BIOS for Sapphire NITRO+ Rx 580 4GB OC p/n 299-1E366-101SA
Title: Re: NEED HELP !!! ITS URGENT Post by: xxcsu on January 15, 2018, 11:36:33 PM what is your bios version number ?
Title: Re: NEED HELP !!! ITS URGENT Post by: mshordja on January 16, 2018, 10:46:03 AM PLEASE HELP!!! ASROCK H81 PRO BTC R2.0 3x Sapphire Nitro RX 580 4GB INTEL G3420 Processor with 8GB RAM 120GB SSD NEW VERSION RISERS ANTEC 1300W 80Plus Platinum PSU. windows 10Pro 64bit Blockchain version Drivers Atidag patcher virtual memory increased CLAYMORE MINER DONE!! everything is setup and running pretty solid on stock setting. i flashed GPUs none by one and testing for 20 to 30 mins >> All fine i add 2nd GPU and did the same >> all fine i flashed my 3rd GPU bios and when mining getting start and trying to creat 3rd GPU's dag file, a blue screen appears saying" THREAD STUCK IN DEVICE DRIVER" and system restart. But when i upload original BIOS back to any of GPU, mining started without any problem and it ran more than 14hours until i repeat the same process but endup finding with same error " THREAD STUCK IN DEVICE DRIVER" and system restart. I did tried to update motherboad's bios but ASROCK H81 PROBTC R2.0 don't have latest BIOS as previous OLD H81 PRO BTC have. I tried to upgrade with H81 PRO BTC BIOS file versions from P1.30 to P2.30 but didn't detect by ASROCK H81 PRO BTC R2.0 PLEASE HELP ME!!! there are several reason for the crash, what drivers are you using? overclocking downclocking are you using? Check the 3-rd riser is working alone, give some more info to analise? what drivers are you using? - Blockchain version of drivers overclocking downclocking are you using? - I flashed bios with bit over clocking -cclock 1150 -mclock 2050 -cvddc 900 -mvddc 900 Check the 3-rd riser is working alone - I replaced riser, swap the risers and also swap the cards..i have already described in OP Try and give feedback Title: Re: NEED HELP !!! ITS URGENT Post by: mshordja on January 16, 2018, 10:47:57 AM Where I can find best modded BIOS for Sapphire NITRO+ Rx 580 4GB OC p/n 299-1E366-101SA i have this more than 50pcs of this card, the max without errors and incorrect shares in dual is getting 29.4MhsTitle: Re: NEED HELP !!! ITS URGENT Post by: treanski on January 16, 2018, 12:06:01 PM maybe the 3 gpu have different memory, its possible even on 3 cards from the same brand
Title: Re: NEED HELP !!! ITS URGENT Post by: orangelemon on January 16, 2018, 05:44:59 PM what is your bios version number ? here is my original bios version : 015.050.002.001.000000 Memory type : Elpida P.S : All 3 580s are will Elpida Memory Sorry for late reply Title: Re: NEED HELP !!! ITS URGENT Post by: bigjee on January 16, 2018, 05:57:52 PM Follow these steps.
-Download ATIwinflash, (make sure only the card you want to flash is connected) and save your bios-call it RX580_original.rom or something meaningful. -Then use https://github.com/jaschaknack/PolarisBiosEditor to open the RX580_original.rom and make sure the mem timings show up. Click 1 Click timing patch (see image below). A popup box will show it is going to apply good mem timings so go ahead and click okay. -Now save the bios as RX580_modded.rom and open Atiwinflash (make sure the card you want to flash is selected) navigate to where you saved the modded rom and select program. The screen will pause for 30sec to a minute (do not interrrupt this process). -Apply pixel patcher after if needed (device manager code 43 means apply the pixel patcher). -Run the miner software and tweak your OC settings. https://s10.postimg.org/nvmvkafd5/Capture.png |