|
Title: Not all Erupters detected, patience? Post by: Squeeky4711 on September 14, 2013, 04:44:12 AM First off I'm a newbie and I apologize ;D
Got my first Erupters today, a total of 14. I'm running MinePeon, with 3x MCM hubs. All erupters are plugged into front hub port with fan pointed directly on them. I have Wifi dongle / First hub plugged into Pi onboard Connected to first hub is 4x Erupter, 1x Artic Fan, and 2x addition hubs 2x hubs have 5 Erupters in each. Cgminer is only seeing 10 devices, however if I connect one of the erupters it is not recognizing directly to Pi it finds it. Am I doing something wrong? Title: Re: Not all Erupters detected, patience? Post by: Trongersoll on September 14, 2013, 09:56:24 PM First off I'm a newbie and I apologize ;D Got my first Erupters today, a total of 14. I'm running MinePeon, with 3x MCM hubs. All erupters are plugged into front hub port with fan pointed directly on them. I have Wifi dongle / First hub plugged into Pi onboard Connected to first hub is 4x Erupter, 1x Artic Fan, and 2x addition hubs 2x hubs have 5 Erupters in each. Cgminer is only seeing 10 devices, however if I connect one of the erupters it is not recognizing directly to Pi it finds it. Am I doing something wrong? Have verified that the hubs have enough po power the erupters? Which erupters aren't being seen? Is it the hub with the other hubs plugged into it? Title: Re: Not all Erupters detected, patience? Post by: techman05 on September 20, 2013, 12:58:53 AM Does the hub have any specific brand. I just ended up ordering a rosewill 10 port hub over recommendations that my hub was under-qualified for the pi now my few eroupters are all picked up at cgminer startup. I'm still working out the kinks since my pi is freezing or my usb to ps2 is not functioning after cgminer starts up for a while.
Just found this while typing so it may be a matter of not using cgminer as well. https://bitcointalk.org/index.php?topic=296936.0 Title: Re: Not all Erupters detected, patience? Post by: wetjet43 on October 26, 2013, 01:49:42 AM I'm having this problem too. My hubs are sufficiently powered. I've got 3 - 7 port hubs. On one of them, all 7 miners work. The other 2, every other miner works. Frustrating!
https://bitcointalk.org/index.php?topic=318327.0 Title: Re: Not all Erupters detected, patience? Post by: balanghai on October 26, 2013, 01:52:25 AM Is your OS clean installed? What are the other USB peripherals you plugged in your bus? Maybe just needs a fresh wheezy.
Title: Re: Not all Erupters detected, patience? Post by: vm1990 on November 02, 2013, 12:23:16 AM scotty we need more power
Title: Re: Not all Erupters detected, patience? Post by: balanghai on November 02, 2013, 12:39:27 AM Try a 10amp 5volts adapter, it should be more than enough to power up the Erupters.
Title: Re: Not all Erupters detected, patience? Post by: madcratebuilder on November 02, 2013, 04:08:53 PM Try a 10amp 5volts adapter, it should be more than enough to power up the Erupters. I've had those slowly drop in output, plenty of power for 6-10 days then miners started dropping off. PITA to find that problem. I'm using all Rosewill rhb-520's with the Rosewill psu, they well run 8 miners each hub. I only run 7 so I have a half amp of head room. Fewer rejects and hw error, better hash. |