|
Title: What does this error mean Post by: Kasposhi on March 28, 2025, 09:45:42 PM Just setup the KS3 Antminer and its overheating and shutting down within 2 minutes, hoping someone could give some insight into this error message:
Code: ===========================================Miner log=========================================== time="2025-03-28 10:57:39" level=error pid=1372 msg="invalid URL -- ''" time="2025-03-28 10:57:39" level=error pid=1372 msg="invalid URL -- ''" time="2025-03-28 10:57:39" level=error pid=1372 msg="invalid URL -- ''" time="2025-03-28 10:57:39" level=notice pid=1372 msg="opt_algo 11, kas_2380" time="2025-03-28 10:57:39" level=notice pid=1372 msg="Miner compile time: Tue Apr 9 16:43:13 CST 2024 type: Antminer KS3" time="2025-03-28 10:57:39" level=error pid=1372 msg="No valid pools, please configure them first!" time="2025-03-28 10:57:39" level=notice pid=1372 msg=platform_topol_init time="2025-03-28 10:57:39" level=notice pid=1372 msg="Start api function" time="2025-03-28 10:57:39" level=notice pid=1372 msg=check_machine_info time="2025-03-28 10:57:39" level=warn pid=1372 msg="port 427 already exported" time="2025-03-28 10:57:39" level=warn pid=1372 msg="port 429 already exported" time="2025-03-28 10:57:39" level=warn pid=1372 msg="port 431 already exported" time="2025-03-28 10:57:39" level=warn pid=1372 msg="port 433 already exported" time="2025-03-28 10:57:39" level=warn pid=1372 msg="no board pluged in socket 432" time="2025-03-28 10:57:39" level=warn pid=1372 msg="port 426 already exported" time="2025-03-28 10:57:39" level=warn pid=1372 msg="port 428 already exported" time="2025-03-28 10:57:39" level=warn pid=1372 msg="port 430 already exported" time="2025-03-28 10:57:39" level=warn pid=1372 msg="port 432 already exported" time="2025-03-28 10:57:39" level=notice pid=1372 msg="chain_offset 0, chain 0" time="2025-03-28 10:57:39" level=notice pid=1372 msg="chain_offset 1, chain 1" time="2025-03-28 10:57:39" level=notice pid=1372 msg="chain_offset 2, chain 2" time="2025-03-28 10:57:39" level=notice pid=1372 msg="reset fpga" time="2025-03-28 10:57:39" level=notice pid=1372 msg="Begain check_fan_valiad" time="2025-03-28 10:57:40" level=notice pid=1372 msg="check_fan_speed ok, fan_num = 4" time="2025-03-28 10:57:40" level=notice pid=1372 msg="eeprom add device: 0" time="2025-03-28 10:57:40" level=notice pid=1372 msg="eeprom add device: 1" time="2025-03-28 10:57:40" level=notice pid=1372 msg="eeprom add device: 2" time="2025-03-28 10:57:52" level=notice pid=1372 msg="start the http thread." time="2025-03-28 10:57:52" level=notice pid=1372 msg="start listen on 6060 ..." time="2025-03-28 10:57:52" level=notice pid=1372 msg="httpListenThread start ret=0" time="2025-03-28 10:57:52" level=error pid=1372 msg="Sweep error string = N:4" time="2025-03-28 10:57:52" level=error pid=1372 msg="No servers were found that could be used to get work from." time="2025-03-28 10:57:52" level=error pid=1372 msg="Please check the details from the list below of the servers you have input." time="2025-03-28 10:57:52" level=error pid=1372 msg="Most likely you have input the wrong URL, forgotten to add a port, have not set up workers, or the network was disconnected." time="2025-03-28 10:57:52" level=warn pid=1372 msg="Pool: 0 URL: User: Password: " time="2025-03-28 10:57:52" level=warn pid=1372 msg="Pool: 1 URL: User: Password: " time="2025-03-28 10:57:52" level=warn pid=1372 msg="Pool: 2 URL: User: Password: " time="2025-03-28 10:57:52" level=error pid=1372 msg="No servers could be used!" time="2025-03-28 10:59:02" level=warn pid=1372 msg="Pool is activing." time="2025-03-28 10:59:02" level=notice pid=1372 msg="all backend runtimes have been poweroff." time="2025-03-28 10:59:02" level=notice pid=1372 msg="set_miner_start_time total_tv_start_sys=123 total_tv_end_sys=124" time="2025-03-28 10:59:08" level=notice pid=1372 msg="Initializing the power, please wait, this may take up 1 minute..." time="2025-03-28 11:00:13" level=notice pid=1372 msg="bitmain power fw version: 0019" time="2025-03-28 11:00:19" level=notice pid=1372 msg=start_heartbeat_thread time="2025-03-28 11:00:20" level=notice pid=1372 msg="enable power watchdog: 0x0001" time="2025-03-28 11:00:21" level=notice pid=1372 chain=0 msg="ChipSetting_get_addr_KAS_2380 detect 92 chips" time="2025-03-28 11:00:21" level=notice pid=1372 chain=0 msg="top_init_kas start" time="2025-03-28 11:00:23" level=notice pid=1372 chain=0 msg="ChipSetting_get_addr_KAS_2380 detect 92 chips" time="2025-03-28 11:00:25" level=notice pid=1372 chain=1 msg="ChipSetting_get_addr_KAS_2380 detect 92 chips" time="2025-03-28 11:00:25" level=notice pid=1372 chain=1 msg="top_init_kas start" time="2025-03-28 11:00:27" level=notice pid=1372 chain=1 msg="ChipSetting_get_addr_KAS_2380 detect 92 chips" time="2025-03-28 11:00:30" level=notice pid=1372 chain=2 msg="ChipSetting_get_addr_KAS_2380 detect 92 chips" time="2025-03-28 11:00:30" level=notice pid=1372 chain=2 msg="top_init_kas start" time="2025-03-28 11:00:32" level=notice pid=1372 chain=2 msg="ChipSetting_get_addr_KAS_2380 detect 92 chips" time="2025-03-28 11:00:34" level=notice pid=1372 msg="check bringup temperature 40 C" time="2025-03-28 11:00:34" level=notice pid=1372 msg="Initializing chip cluster, please wait, this may take up to 2 minutes..." time="2025-03-28 11:01:40" level=notice pid=1372 msg="set PT2_freq to 675.00, current voltage 1700" time="2025-03-28 11:01:50" level=notice pid=1372 msg="set_miner_start_time total_tv_start_sys=291 total_tv_end_sys=292" time="2025-03-28 11:01:55" level=notice pid=1372 msg=start_voltage_monitor time="2025-03-28 11:01:55" level=notice pid=1372 msg="start freq_compensate_thread" time="2025-03-28 11:02:40" level=warn pid=1372 chain=0 msg="Chip temperature is too high, enable protection. Bias freq:-10.00" time="2025-03-28 11:02:41" level=warn pid=1372 chain=1 msg="Chip temperature is too high, enable protection. Bias freq:-10.00" time="2025-03-28 11:02:42" level=warn pid=1372 chain=2 msg="Chip temperature is too high, enable protection. Bias freq:-10.00" time="2025-03-28 11:02:51" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:02:51" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:02:51" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:02:51" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:02:51" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:02:51" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:02:51" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:02:51" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:02:51" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:02:51" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:02:51" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:02:51" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:02:52" level=warn pid=1372 poolno=0 msg="reject reason: duplicate" time="2025-03-28 11:03:42" level=fatal pid=1372 chain=2 msg="high temp exceed limit (3), max_chip_temp = 93, max_pcb_temp = 78!" time="2025-03-28 11:03:42" level=error pid=1372 msg="Sweep error string = P:1." time="2025-03-28 11:03:43" level=error pid=1372 chain=2 error="temp too high" msg=check_temp time="2025-03-28 11:03:43" level=error pid=1372 msg="Sweep error string = P:1" time="2025-03-28 11:03:43" level=fatal pid=1372 chain=2 msg="high temp exceed limit (4), max_chip_temp = 93, max_pcb_temp = 78!" time="2025-03-28 11:03:43" level=error pid=1372 msg="Sweep error string = P:1." time="2025-03-28 11:03:44" level=fatal pid=1372 chain=2 msg="high temp exceed limit (5), max_chip_temp = 93, max_pcb_temp = 78!" time="2025-03-28 11:03:44" level=error pid=1372 msg="Sweep error string = P:1." time="2025-03-28 11:03:45" level=fatal pid=1372 chain=2 msg="high temp exceed limit (6), max_chip_temp = 93, max_pcb_temp = 78!" time="2025-03-28 11:03:45" level=error pid=1372 msg="Sweep error string = P:1." time="2025-03-28 11:03:46" level=fatal pid=1372 chain=2 msg="high temp exceed limit (7), max_chip_temp = 94, max_pcb_temp = 79!" time="2025-03-28 11:03:46" level=error pid=1372 msg="Sweep error string = P:1." time="2025-03-28 11:03:47" level=fatal pid=1372 chain=2 msg="high temp exceed limit (8), max_chip_temp = 94, max_pcb_temp = 79!" time="2025-03-28 11:03:47" level=error pid=1372 msg="Sweep error string = P:1." time="2025-03-28 11:03:48" level=fatal pid=1372 chain=2 msg="high temp exceed limit (9), max_chip_temp = 94, max_pcb_temp = 79!" time="2025-03-28 11:03:48" level=error pid=1372 msg="Sweep error string = P:1." time="2025-03-28 11:03:49" level=fatal pid=1372 chain=2 msg="high temp exceed limit (10), max_chip_temp = 94, max_pcb_temp = 79!" time="2025-03-28 11:03:49" level=error pid=1372 msg="Sweep error string = P:1." time="2025-03-28 11:03:50" level=fatal pid=1372 poweroff=true msg="high temp 1 low temp 0 fan err 0 read no temp 0, uneffective temp 0, lost connection too long 0" Would a faulty PSU cause these kind of errors? Title: Re: What does this error mean Post by: miner29 on March 29, 2025, 01:47:15 PM First line says URL is invalid.
Check your url as you dont appear to be connecting to a pool Title: Re: What does this error mean Post by: JayDDee on March 29, 2025, 08:53:57 PM I think the answer is in the question. It's overheating, deal with that. Make sure the fans are all working & clean
& you have good air flow. ASICs are designed for data centres that have environmental control so you might need more cooling. Title: Re: What does this error mean Post by: Kasposhi on March 31, 2025, 02:34:48 AM First line says URL is invalid. Eventually it connects to pool and once the hasboards start hashing, the temperature increases, excessively infact.Check your url as you dont appear to be connecting to a pool I think the answer is in the question. It's overheating, deal with that. Make sure the fans are all working & clean I think you're right, its 4 miners in a small room, with little air flow. Was just wondering if there was some hardware failure.& you have good air flow. ASICs are designed for data centres that have environmental control so you might need more cooling. Thanks, I shall address the cooling situation. Title: Re: What does this error mean Post by: Ers900 on April 29, 2025, 10:03:25 PM Did you manage to find a solution?
I’m in a similar dilemma! |