Show Posts
|
Pages: [1] 2 3 »
|
Hey nederlandse bitcoiners, Ik was van plan naar dit concert te gaan maar krijg net te horen dat ik dan in het buitenland zit. Gaat om 4 etickets voor Adele op 6 juni, 2e ring vak 211. Vraagprijs +/- 2 btc.
Als je interesse hebt laat het weten anders verkoop ik ze gewoon via de 'normale' kanalen.
|
|
|
200 btc at €5000, that would be awesome! Still have to get 200 btc though....
|
|
|
Bohoo OP go away, what a bad attempt to spread some negative speculation.
|
|
|
500 is incoming, and towards the halving this will only get higher!
|
|
|
Future looks good, should be interesting to see what happens in the upcoming months with the halving coming up.
Buying now looks like a good plan.
|
|
|
4 technobit hex16c running at 95 GH/s!
|
|
|
On the picture you see your hexc fan spinning , while your fan of your psu looks like it's doing nothing . Just a question , did you short your psu (like putting a paperclip on the green and black wire ? If the hexc get's 12volt the red led wil be blinking
(Pardon my english)
I have a corsair rm750 which has 0rpm mode with the fan if less than 40% of total watt is used. Should the fans spin when i only plug them into the psu? Ok just read about shorting the PSU howevr all my wires are black edit: youtube saved me..
|
|
|
Hey Guys, I still cant gey my miners up and running. I have connected one miner now to the technobit tplink router and this is all that happens. I have the feeling that i am making a noob mistake somewhere but i just can't figure it out. Who can help? Here are my settings: There is no 12v power supply to the board. Double check it. Is molex connected and ok? Are you using some extension cable to molex? This is my setup: The hex16 has a red and a yellow led lit.
|
|
|
Hey Guys, I still cant gey my miners up and running. I have connected one miner now to the technobit tplink router and this is all that happens. I have the feeling that i am making a noob mistake somewhere but i just can't figure it out. Who can help? Here are my settings:
|
|
|
Hey Guys, I still cant gey my miners up and running. I have connected one miner now to the technobit tplink router and this is all that happens. I have the feeling that i am making a noob mistake somewhere but i just can't figure it out. Who can help?
|
|
|
Hey there everyone! I am so close but there is still something going wrong. Anyone know why this happens? Are the boards powered 12v? Doubble check it pls I have a corsair rm750 connected to the boards. I am retrying everything again tonight i'll seewhat happens otherwise i'll set up TW. Other thing a common mistake that I have with some customers. If your boards are with wire terminal did you happened to connect the red wire to + and black to - GND? If so change it to Yellow + and Black - GND. If this is not the case , please excuse me I was not intending to offend you. Best Martin Hi Martin, Thanks for the support! I have the molex connector so that shouldnt be a problem. I will be plugging in the boards one by one tonight to see what happens.
|
|
|
Hey there everyone! I am so close but there is still something going wrong. Anyone know why this happens? Are the boards powered 12v? Doubble check it pls I have a corsair rm750 connected to the boards. I am retrying everything again tonight i'll seewhat happens otherwise i'll set up TW.
|
|
|
most probaly problrm with the USB hub. Also in the web interface change the defaut miner to HEXC
Which web interface on the router or on cgminer? Do i need to buy a different usbhub?
|
|
|
Hey there everyone! I am so close but there is still something going wrong. Anyone know why this happens?
|
|
|
My MR3020 does nothing. Who can help met out? When i plug in my Tplink router that i bought from technobit my computer doesnt recognise it. The power light and wps/reset go on but thats it. I hook up the router to my laptop and nothing... On which setting do you have your router? 3g/4g or wisp or AP? Getting tired of trying to problem solve Technobit equiment.
Edit: The person that helps me solve all my hex16a2 and mr3020 problems tonight i will reward with my first day of earning from mining. I will be online again in 3 hours PM me if you want to help.
|
|
|
Hi! I have been trying to get a board working on my laptop (win7) but no luck so far. edit: no LED is lighting up on the board the board is being powered by a corsair rm750 is this correct??
I have received the tplink router with technobit firmware and tomorrow I want to connect four boards to it. Does anyone have a tutorial for how i should do this? Do i have to change the fan that is supplied with boards?
Too bad if win 7 not working with you because it's the easiest way. The TL-MR3020 come with ip 192.168.0.99. You need to configure password, ssh , date , time, timezone, then cgminer configuration or network if you want. Do it all slowly, wait until all saving process done before closing browser tab. The FAN is the best available now so no need to change unless you really need to. Ah should be a piece of cake :S hehe what should i use for ssh?
|
|
|
Hi! I have been trying to get a board working on my laptop (win7) but no luck so far. edit: no LED is lighting up on the board the board is being powered by a corsair rm750 is this correct??
I have received the tplink router with technobit firmware and tomorrow I want to connect four boards to it. Does anyone have a tutorial for how i should do this? Do i have to change the fan that is supplied with boards?
|
|
|
Ik had dat probleem ook eens gehad.
Bij mij was het geloof ik een driver issue. door de driver te verwijderen van de computer en opnieuw van de site te installeren was dit probleem bij mij opgelost.
wat het ook kan zijn is een verkeerde instelling van je hashrate/voltage, maar aangezien die stock is bij u betwijfel ik dat.
groeten
Probleem doet zich nog steeds voor. Bij de usb driver zijn nu 2 verschillende files welke van de twee mot ik gebruiken voor de driver?
|
|
|
Overgestapt naar andere computer met windows 7. Heb de handleiding gevolgd maar geen hashing... Zo heb ik het nu ingesteld: wat doe ik nou fout...
|
|
|
|