I keep getting that stupid msvcr100.dll missing error on a new 6 750 ti rig...win 7 64, installed c++ redist 2012 32bit and also the .net framework 4.5 just in case.
Any clues? (using ccminer official compiled binaries)
I did a fresh install of Win 7 64bit the other day and couldn't get mining to work until I installed the 2010 32bit version direct from MS themselves here... http://www.microsoft.com/en-gb/download/details.aspx?id=5555 |
|
|
|
i found that when i am "not looking" at the computer, the load goes up to 85% and speed running at 1.660 mh stable. Once i remote access the computer , it immediately goes down to 1.2 mh and load change to 60% - 70%
Which method? RDP, VNC, TeamViewer, Splashtop etc? |
|
|
|
I am using evga gtx 750 ti SC but i am not able to get my card to run 1.7 mh for x11. Its only running 1.2 - 1.3 mh. All my setting is +0. The gpu load always run around 70% TDP 50%. I am using windows 8.1. Need advise to improve hashrate.
Is this when you trying to run just 1 card or several at the same time? When I run 4 simultaneously I can only get about 1.5mh/s per card. With the same OC I get 1.65mh/s to 1.7mh/s with only 1 card active. I am only running 1 card. I only have a single card now. What OC setting u use ? i saw someone on earlier post (using same model) getting 1.75 mh each running 5 cards. What is your GPU load ? I've got 1310Mhz on the core and zero overclock on the memory. These are two fan Gigabyte 750Ti cards and with all 4 cards active they are at 80% load each according to GPUz. |
|
|
|
I am using evga gtx 750 ti SC but i am not able to get my card to run 1.7 mh for x11. Its only running 1.2 - 1.3 mh. All my setting is +0. The gpu load always run around 70% TDP 50%. I am using windows 8.1. Need advise to improve hashrate.
Is this when you trying to run just 1 card or several at the same time? When I run 4 simultaneously I can only get about 1.5mh/s per card. With the same OC I get 1.65mh/s to 1.7mh/s with only 1 card active. |
|
|
|
I'm getting only 800khash with x11 on my 750ti... :/
My cards only go that low if I've OCd it too high. Reboot your rig and try again. Also, share your command line that you're running just in case. You use it with no OC at all? Iv oced clock +70 and memory -502 My batch file ccminer50 -a x11 -o pool -u user -p password I do overclock, I'm saying I get the low mhash when I overclock TOO MUCH and it errors and the mhash drops  That command line looks fine. Have you restarted the PC since your last post? |
|
|
|
I'm getting only 800khash with x11 on my 750ti... :/
My cards only go that low if I've OCd it too high. Reboot your rig and try again. Also, share your command line that you're running just in case. |
|
|
|
I mining here >> stratum.mine-coin.de:3393 my friend mining on hardcoreminers and he have like triple reward there with much less Mh/s and he start much later than me.  Yes that can change any second compared to diff , block found Do they still have 10 coin payout? We have 80.000 maybe they didnt set it up right. They are 80k now like everyone else -> http://cc.mine-coin.de/index.php?page=statistics&action=blocksIt was just that mine-coin.de was the only pool available for the first 10mins and so that mined almost all of the low reward (the first 100) blocks by themselves. By the time Hardcore came online it was 80k all the time. |
|
|
|
Can anyone with MSI cards that has had success mining X11 so far post their config please?
I could only get my MSI 750ti TF cards up to 1280 khash/s, so I must be missing something if people are getting 1600-1800 khash/s
This was with my max OC settings 1210 GPU/ 1675 MEM.
I have a MSI TF 750ti as well. I have the core at 1375mhz and zero mem overclock and I reach 1.6 to 1.7mhs with x11. My command line (apart from the pool, uname, pwd) is the same as yours. Check task manager and make sure you don't have something that's hogging the CPU 25% and over. |
|
|
|
I'm giving X11 a go now on Badgercoin (POW ends tonight) Running on my 4 x 750ti rig I get around 1.5Mh/s when only one card is running. With all 4 cards running, 2 cards per batch file, I get around 2.6Mh/s per pair |
|
|
|
You solo mining jackpot still? Ive hit 7 blocks today
I did 2 days of solo with my 4 x 750ti. On the first day I got 8 blocks and on the second I got 7. The difficulty was around the 68 to 72 range. Now I'm mining it at a pool to compare but the difficulty has dropped to the mid 50s now that the price has also fallen from 2 to 3 sat. Is your pool stuck as well? Miningpoolhub is up to 13280.46% done and climbing fast I missed the signups for mph so i just went with these two instead, no reg required and regular payments straight to the wallet... http://www.hashharder.com/jha/jackpotcoinhttp://www.verters.com/mvpool/jackpotcoinMight be worth jumping off mph for now until they have gone past that unlucky block. |
|
|
|
You solo mining jackpot still? Ive hit 7 blocks today
I did 2 days of solo with my 4 x 750ti. On the first day I got 8 blocks and on the second I got 7. The difficulty was around the 68 to 72 range. Now I'm mining it at a pool to compare but the difficulty has dropped to the mid 50s now that the price has also fallen from 2 to 3 sat. |
|
|
|
I'm down to TAC tac adddress -> TiwwThan3aGczHjTYhroGRYDRKa8thxfZS Thanks! |
|
|
|
As a side note to anyone solo mining jackpot coin. Right now i have 3 750Tis solo mining on the new code, found 3 blocks in 12 hours. Much better then i was getting in the pools
I just fired up 4 x 750Ti (just under 4mh/s per card) on solo and will report back this time tomorrow how many I get. |
|
|
|
Anyone else getting this in their SGMiner window whlie mining on Pool.mn?
"getaddrinfo() in setup_stratum_socket() returned 11001: No such host is known"
I'm still getting accepts and ZERO rejects but the above line appears every four or five "accepted..." lines.
Maybe your "pool 0" is not correct. check please. I removed the pools above Pool.mn and now the above error does not appear. Thanks |
|
|
|
|
Anyone else getting this in their SGMiner window whlie mining on Pool.mn?
"getaddrinfo() in setup_stratum_socket() returned 11001: No such host is known"
I'm still getting accepts and ZERO rejects but the above line appears every four or five "accepted..." lines.
|
|
|
|
For anyone that missed the initial action just after opening or perhaps wondered how many sold at the current high of 20k sat (not very many)...  (timestamps are UTC+0) |
|
|
|
40Gh/s now with the diff at 850+ I'm guessing there's one or two multipools jumping on this |
|
|
|
Anyone having any luck with UTC now that the numbers went through the floor? Or would this even work over there?
My 750ti's were getting like 75KHash/s each after the increase. What are you getting with your mods and 750s after the change?
Before the change in N-factor over the past day or so, I was getting 60kh/s on UTC (and 300kh/s on normal scrypt so you can roughly judge my overclock on the the card). The setting for UTC I was using before the n-factor change was... -l T5x11 -b 4096 -i 1 -a scrypt-jane:UTC What command line switches and OC on the card were you using to achieve 75kh/s? At the moment with the same switches I'm only get 1.35kh/s Apparently I was exhausted last night, and mis-stated the total as each card and not total. I am getting ~19.10 khash/s for each card after the switch, and 75.80 khash/s total for 4 x 750 ti cards. That being said it still seems more than what you posted, so here is the config I was using if it helps you. Sorry for the confusion. cudaminer.exe -a scrypt-jane:UTC -m 1 -i 0 -H 2 Autoconfig chose T31x1. Thanks for posting this, I will give it a try later |
|
|
|
Anyone having any luck with UTC now that the numbers went through the floor? Or would this even work over there?
My 750ti's were getting like 75KHash/s each after the increase. What are you getting with your mods and 750s after the change?
Before the change in N-factor over the past day or so, I was getting 60kh/s on UTC (and 300kh/s on normal scrypt so you can roughly judge my overclock on the the card). The setting for UTC I was using before the n-factor change was... -l T5x11 -b 4096 -i 1 -a scrypt-jane:UTC What command line switches and OC on the card were you using to achieve 75kh/s? At the moment with the same switches I'm only get 1.35kh/s |
|
|
|
|
Show Posts
