Ok folks !
I've made my test for my mining daily income ! Here's the results
My conclusion are that the numbers aren't adding up even closely to the estimated daily income....
Ex: Yesterday morning at 10:00 I was exactly at 0.00010314 in my account 63 kh/s for an estimated daily income of 0.00062183 btc 2974 kh/s as referral for an estimated daily income of 0.00137876 btc
This morning at 10:00 I am at 0.00080290 in my account still 63 kh/s and 2975 referral kh/s
So I made 0.00080290-0.00010314= 0.00069976 btc for the last entire day instead of the 0.00062183 + 0.00137876 = 0.00200059 btc estimated for the daily income !
That's 35% of the estimated income !!
So either .... The whole estimated daily income system is completely screwed or my account is ?!?!
So anyone with the same results ?!?!
Any admin could help here ?
Thx
|
|
|
Rosewill 10-port USB 2.0 hubs are what I'm planning to use 5 U2's on...
Your planning to... so it means you haven't tried it ?
|
|
|
Hi all,
I'm trying to find a usb hub on which I am gonna be able to plug and run 5 antminers U2.
Any recommandation here specialy for the fitting.
THX !!!
|
|
|
I'm in doubt here... My estimated daily income is far from what I am actually receiving everyday....
I'm giving it another day to verify
Am I the only one here, that the numbers from your hashrate and from the referrals aren't adding up daily with the daily estimated income ?
|
|
|
Is there any configuration needed in the config file for a SLI setup !?
Because when I run cudaminer with SLI activated with -d 0,1 it only detects GPU #0 and my hashrate is equal to only one gpu... And if I start 2 cudaminer one with -d 0 and the other with -d 1, its seems that both cudaminer are working on the same gpu... so my computer is super slow...
To make it work I have to deactivate the SLI setup and run 2 instances of cudaminer... -d 0 and -d 1
Is there a way to make it work with only one cudaminer ?
THX all
|
|
|
If only my 32 referred users could have more than 2750 kh/s combined !! arrrfffff
Well, thats not so bad actually. Worst I saw was 160 refs with a whopping total of 1.4 Mhs combined Yeah, in fact its more 8 users with 2750 and 24 with 0 !
|
|
|
If only my 32 referred users could have more than 2750 kh/s combined !! arrrfffff
|
|
|
For 265$ at current exchange value 265$ / 590$/btc = 0,449152542btc 0,449152542btc / 0.0108 btc/Gh/s (CEX.IO) = 41.6GH/s for the same price...
|
|
|
At this price ($265 per unit 11 GH/s) the following bitcoin profit calculator showing that, the hardware cost will break even after 2 years+? Ref. http://www.bitcoinx.com/profit/Can someone please confirm this? Not sure what I am missing here. That's the problem with pounds... they are worth too much... you lose your wallet with the conversion into USD... The price is too high in terms of investment, you are gonna get much more hashing power buy investing that amount of money in bitcoins and then buy gh/s in a cloud mining service... but you dont get to have the cool device...
|
|
|
Oh I had to do a little of reopening the client and make it first run at 1,6 then I am able to overclock it to 2,2. But there is one that do not want to work at 2,2 but at 2,1 yes.
Might it be my usb port that doesn't receive enough power ? Because I have 3 block erupters and 2 antminers directly plug in my computer usb ports...
Thx Doc !!!
I don't have an U2 but afaik they are the same hardware as the U1's (which I have a bunch of). For me some couldn't go up to 2GH/s without throwing HW-errors in the 50% range. The problem is with the quality of the chip. Some need a little bit more voltage than others. So I think the only possibility for you to get all of them to 2,2GH/s is with a little voltage mod of the not so good performing ones. For me I only upped them about 0.08V but that did the trick. Your computers usb ports "should" be able to supply enough power or shut off completely I think. Thx, one running at 2,2 and the other at 2,1 without problems for now !
|
|
|
Since Bitminter decided to go with blackLotus for DDOS protection everything is very cleeeeeeeeeean !!! Scrypt.cc should think about it, because if nothing is done the site will be kill in the shell... and it would be a shame.
|
|
|
Oh I had to do a little of reopening the client and make it first run at 1,6 then I am able to overclock it to 2,2. But there is one that do not want to work at 2,2 but at 2,1 yes.
Might it be my usb port that doesn't receive enough power ? Because I have 3 block erupters and 2 antminers directly plug in my computer usb ports...
Thx Doc !!!
|
|
|
oh wow !!! didn't even know about that !!!
But they are not working anymore...
2014.03.19 [10:54] Icarus (COM9) ERROR: Selftest error. Expected nonce 0xFFFFFEFE but got 0xFFFFFE0E. ?!?!?
|
|
|
Hi all,
Just received 2 antminers U2.
First, they are hashing at 1.6gh/s ... And second does anyone know how to overclock them to 2,2gh/s ?
Thx for your help.
|
|
|
Can anyone help me setting up my antminers. Just received supposedly 2 x U2, but they are hashing at 1.6Gh/s on the bitminter client. How do I overclock them to at least 2Gh/s ?! It's written everywhere that there are easy to overclock but nothing on HOW !!!
Thanks for your help.
|
|
|
I've send some Btc from BTC-E. Bitcoins out, I can see it here http://blockexplorer.comBut nothing in my account show's up... no confirmation waiting
|
|
|
Anybody has an idea why when I tried overclocking my gtx 465 with the nvidia configuration panel or any other overclocking program, nothing really happen, even worst reaching a certain point, the hashrate on cudaminer starts decreasing to 90 or 50 kh/s....
On another computer I was getting 180kh/s at gpu clock +175 without any problems. (PSU was only 380w) But now can't reach more than 120kh/s and overclocking do absolutely nothing.... ?!?! (with a corsair 750w and a better motherboard...)
Any clue why ?!?!
|
|
|
It's possible, but it's like putting a Ford 6.2 V8 in a Prius. It's possible, but you're basically rebuilding the Prius from the ground up to put a V8 in it.
Ok I see, great metaphor !
|
|
|
|