Any news on a successor to the U2 USB miner, the U3? Soon, I guess. The U3 will be using the new BM1382 chip. Probably will hash around the hr of 1 BM1382 (which is 15GH/s)? I don't think so, the Chip needs by 15 GH/s to much power, but I think 5 - 8 GH/s with one USB miner (One Chip) are possible!? greets
|
|
|
Effizienter und schneller werden die schon, sie sind nur einfach viel zu teuer (um noch profitabel zu sein).
Wenn der Miner in der Anschaffung schon mehr kostet, als er an Erträgen einbringt, nützt die weltbeste Effizienz nichts und das ist leider bei so ziemlich jedem verfügbaren Bitcoin-Miner der Fall.
Da die Leute die Dinger aber trotzdem immernoch kaufen, ist auch nicht davon auszugehen, daß sich an den Preisen in Zukunft was ändert.
Brauchst du dir nur den neuen Bitmain Chip ansehen: https://bitcointalk.org/index.php?topic=656461.msg7374916;boardseen#newDa wird sich noch lange nichts ändern... hätte nicht gedacht, das das Interesse so groß ist!? mfg Edit: Interessant eventuell zum Testen aber nie im Leben Profitabel Eventuell ein kleiner 5 GH/s USB Miner mit einem Chip wäre da schon interessant für Testzwecke...
|
|
|
Thanks Luke. That go me a step farther. Now I got configure: error: Could not find HASH_ITER - please install uthash-dev 1.9.2+
tried install uthash-dev 1.9.2+ but, of course, that didn't work.
Don'cha just hate newbies
but root@sunwatch:~# sudo aptitude install uthash-dev No packages will be installed, upgraded, or removed. 0 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 0 B of archives. After unpacking 0 B will be used.
and than always the same and I don't know? checking whether HASH_ITER is declared... no configure: error: Could not find HASH_ITER - please install uthash-dev 1.9.4+ On my Pi is the newest Kernel!? greets
|
|
|
Find ich auch "Geil" das Caseking da ein Vorreiter ist mfg
|
|
|
Habe mir selber bei einem guten Angebot auf ebay 5x Antminer U2 für ca 50 € angeschafft, aber eher weil ich noch einen großen USB Hub und einige Lüfter übrig hatte und mich bunte Lichter immer noch faszinieren Gewinn werde ich damit nie erwirtschaften, es ist mehr das Gefühl Teil des großen Bitcoin Schürfens zu sein. Sobald der minimale Auszahlbetrag erreicht worden ist, werden die 5 noch Lotto spielen dürfen 1+ au meine Einstellung da die sehr geringe Kosten verursachen sind die zu vernachlässigen... mfg
|
|
|
Welcher Wechselkurs wird als Referenz verwendet?
Mfg
|
|
|
Payment received, perfect!
Posts: 316
Address: 18kpcEdDjeZ7nifaE6CvGLPs1SBBV2gerf
THX and regards
|
|
|
Good day, i have an existing problem with my configuration: 8 x Antminer U2 + 8 x BFx2 Bitfury as soon as I both operate (. / configure - enable-bitfury - enable-icarus) remains Cgminer hang over again, and "watchdog" restarts the Raspberry new! Once I only BFx2 Bitfury (. / Configure - enable-bitfury) used, runs the Cgminer 24/7. 0: BXM 0 : | 3.810G / 3.751Gh/s WU:52.9/m 1: BXM 1 : | 2.394G / 3.187Gh/s WU:44.6/m 2: BXM 2 : | 3.136G / 3.167Gh/s WU:44.6/m 3: BXM 3 : | 2.990G / 3.006Gh/s WU:42.1/m 4: BXM 4 : | 3.767G / 3.819Gh/s WU:53.7/m 5: BXM 5 : | 3.894G / 3.919Gh/s WU:55.0/m 6: BXM 6 : | 3.952G / 3.932Gh/s WU:55.5/m 7: BXM 7 : | 3.804G / 3.867Gh/s WU:54.4/m -------------------------------------------------------------------------------- [2014-06-12 23:19:41] Zero length string passed to valid_hex from in util.c ini tiate_stratum():2609 [2014-06-12 23:19:41] Zero length string passed to valid_hex from in util.c ini tiate_stratum():2609 Exactly the same is in the use of Antminer (. / Configure - enable-icarus)? The problem is only with the simultaneous use, is it possibly there is a compatibility issue between the two drivers? I had raised the issue before, but still wanted to thoroughly test! On the Pi is the newest Kernel installed. regards
|
|
|
Hallo Space,
da der Raspcontrol zur Zeit eigentlich gar nicht rund läuft deinstalliere ich ihn wieder mal sehen ob er mit einer neueren Cgminer Version wieder läuft???
mfg und trotzdem Danke
|
|
|
Hallo, danke an das habe ich auch gedacht, darum hängt der Pi an einem extra Netzteil. Erst wenn alles Stabil laufen würde, würde ich den Pi dazu hängen mfg
|
|
|
Hallo,
da der Raspi nur max. 1,2 A aufnehmen kann ist das mmn überdimensioniert. Und nach meiner Messung zieht er bei mir nur max. 0,6A also gehe ich eher von einer Software Inkompatibilität aus!?
mfg
|
|
|
Danke, habe aber schon 3 verschiedene bis 1,5A versucht und immer das selbe...
Mein Pi zieht ca 0,6A also vollkommene ausreichen!
Mfg
|
|
|
Hello, i know it's a cheap comparative and no measurement, but on a other Power Supply ( Solo 1,5A@5V) is the measurement with the USB about 4,95V. It should also be noted tolerances: For my purposes, it was sufficient that I've seen that it can not be due to the current strength. When comparing the one should also note that the ~ 4.5V were measured at load in idle it was at ~ 4.85 V. regards
|
|
|
OK, when i make a debug file, help that? Is this so correct when im using the ANT and BiFury? ./configure --enable-bitfury --enable-icarus
make -g Then i build a debug file? It's strange, I hardly use the ants launches the Pi always new (since Cgminer hangs) at the BiFurys there are no problems? regards Edit: At time i use the Cgminer 4.2.3 and over 4 hours it's all OK with the configs no Pi restart...!!?? Hello after a few of tests, I think its a compatibility problem between Cgminer and a other Software (RaspControl for the Cgminer) to Log the Cgminer! But the crashes are only by the Antminers and very often with the new 4.3.4 with 4.2.0 it's better. regards
|
|
|
Hello guys, so I have test a little bit he HUB, and I think it’s a good quality Only the voltage is on the lower end of the USB standard. My Devices: 10 x Antminer U2+ (~ 1,8 GH/s / anu-freq:225), 8 x Bfx2 (~ 3,5 GH/s / bxm-bits:53) Here my table: USB port | Device | Voltage | amperage | 1 | Bfx2 | 4,45 | 1,01 | 2 | Antminer | 4,55 | 0,61 | 3 | Bfx2 | 4,40 | 1,05 | 4 | Antminer | 4,50 | 0,62 | 5 | Antminer | 4,60 | 0,64 | 6 | Bfx2 | 4,40 | 1,05 | 7 | Antminer | 4,60 | 0,64 | 8 | Bfx2 | 4,45 | 1,02 | 9 | Bfx2 | 4,45 | 1,07 | 10 | Antminer | 4,60 | 0,61 | 11 | Bfx2 | 4,45 | 1,01 | 12 | Antminer | 4,55 | 0,61 | 13 | Antminer | 4,65 | 0,59 | 14 | Bfx2 | 4,45 | 1,07 | 15 | Antminer | 4,65 | 0,58 | 16 | Bfx2 | 4,61 | 1,01 | 17 | Antminer | 4,55 | 0,61 | 18 | Antminer | 4,50 | 0,61 | 19 | Empty for Pi later | |
So when the voltage is OK, I can say a good result about the measurement. I hope for the permanent load about 16 A is for the HUB no problem? At time my results from the Cgminer, one Bfx2 is a little bit slower... 0: ANU 0: | 1.770G/1.749Gh/s | A: 624 R: 0 HW:56 WU: 19.4/m 1: ANU 1: | 1.745G/1.758Gh/s | A: 336 R: 0 HW:39 WU: 18.1/m 2: ANU 2: | 1.756G/1.749Gh/s | A: 368 R: 0 HW:56 WU: 17.5/m 3: ANU 3: | 1.785G/1.752Gh/s | A: 416 R: 0 HW:42 WU: 18.6/m 4: ANU 4: | 1.787G/1.756Gh/s | A: 528 R: 0 HW:49 WU: 19.0/m 5: ANU 5: | 1.785G/1.760Gh/s | A: 336 R: 0 HW:35 WU: 17.8/m 6: ANU 6: | 1.756G/1.749Gh/s | A: 464 R: 0 HW:51 WU: 19.0/m 7: ANU 7: | 1.671G/1.744Gh/s | A: 592 R: 0 HW:58 WU: 18.5/m 8: BXM 0: | 3.640G/3.451Gh/s | A:1024 R:16 HW: 0 WU: 50.8/m 9: BXM 1: | 2.759G/2.733Gh/s | A: 880 R:32 HW: 0 WU: 39.1/m 10: BXM 2: | 3.672G/3.689Gh/s | A:1152 R:32 HW: 0 WU: 52.1/m 11: BXM 3: | 3.514G/3.389Gh/s | A: 912 R:32 HW: 0 WU: 49.6/m 12: BXM 4: | 3.464G/3.326Gh/s | A:1232 R: 0 HW: 0 WU: 48.9/m 13: BXM 5: | 3.838G/3.825Gh/s | A:1456 R: 0 HW: 0 WU: 54.2/m 14: BXM 6: | 3.696G/3.786Gh/s | A:1424 R: 0 HW: 0 WU: 52.9/m 15: BXM 7: | 3.298G/3.604Gh/s | A:1088 R:64 HW: 0 WU: 50.6/m 16: ANU 8: | 1.770G/1.755Gh/s | A: 352 R: 0 HW:54 WU: 17.9/m 17: ANU 9: | 1.535G/1.751Gh/s | A: 400 R: 0 HW:46 WU: 17.4/m regards
|
|
|
Hallo Sven,
ich habe mich einmal durch deinen Blog gewühlt und gesehen (BfgMiner Blog), dass es Probleme mit RaspControl und Cgminer gibt!
Hast du da eventuell schon eine Lösung gefunden? Der Neustart des Pis ist für meine Zwecke nicht gerade Optimal!?
Das witzige ist das NUR die Antminers Instabil sind, die BixFurys laufen ohne Probleme und ohne Absturz...
mfg
|
|
|
Das wird die 1% MwSt sein sie ihr euch gegenüber von uns spart...
|
|
|
Mit 2 Watt/GH sind die s1 alles andere als effizient und Netzteile sind auch nicht dabei! Die knapp 3KW muss man erstmal stemmen.
Ich habe dies der Auktion hinzugefügt. Wenn du jetzt noch hinzufügst das man sehr wohl mindestens 2.8 KW an Netzteilleistung hinzukaufen muss und die Stromkosten in die Kalkulation mit einbeziehst... Könnte es passen. Wobei wenn man 7 von den dingern in einem Raum betreibt, der die 2.8KW an abWärme verkraften muss sind die auch nicht mehr so leise Ist schon richtig, aber er will die Teile ja auch noch verkaufen und ein wenig sollte man sich als Käufer auch erkunden... mfg
|
|
|
OK, when i make a debug file, help that? Is this so correct when im using the ANT and BiFury? ./configure --enable-bitfury --enable-icarus
make -g Then i build a debug file? It's strange, I hardly use the ants launches the Pi always new (since Cgminer hangs) at the BiFurys there are no problems? regards Edit: At time i use the Cgminer 4.2.3 and over 4 hours it's all OK with the configs no Pi restart...!!??
|
|
|
Hello and thanks for your answer. I think the problem is the Antminer (Icarus) driver, by me the Raspberry start a reboot when Cgminer hangs (Watchdog). With the 8 x Bifurys (./configure --enable-bitfury) i have no problem the miners run without a reboot! But whn i test my 8 x Antminers U2+ (./configure --enable-icarus) the Cgminer reboot my Raspberry about one time in a hour!? With the command (./configure --enable-bitfury --enable-icarus) its the same? Also the follow command i have set: Raspberry Pi is locking up when running CGMiner
If your RPi is freezing randomly after some time (could be minutes, could be hours or days) with error like Oops: PREEMPT ARM, CPU0 Not tainted printed out over HDMI, and with locked up ethernet and USB interfaces, you have to add following option to the /boot/cmdline.txt file on SD card: slub_debug=FP regards
|
|
|
|