Show Posts
|
Pages: « 1 [2] 3 »
|
Got my first D3 running for 24 hours now, It has already failed 3 times with 2 different hash boards showing XXX in ASCI status, gone after a reboot, update to latest firmware did not help. Is this D3 just fubar from the start? Temps are all normal.
Update, i got 2 more miners setup today, they are also at default frequency setting, but are only hashing at 17ghz frequency at 487 the first are hashing at 19ghz with frequency at 537, both can't be default? All temps are below 70C, i sat fanspeed at 85%
|
|
|
Got my first D3 running for 24 hours now, It has already failed 3 times with 2 different hash boards showing XXX in ASCI status, gone after a reboot, update to latest firmware did not help. Is this D3 just fubar from the start? Temps are all normal.
|
|
|
Getting my first D3 in a few days. Is granatgas the best pool? Are you guys getting payed in DASH, BTC or something eles?
|
|
|
I only cleaned it with air with the fans still in place, maybe i should remove the fans first?
I bought them on alibaba so not sure on the warenty.
Fans are all doing fine, about the same as the working also the temps.
The power supply is the original bitmain so i dont think they are bad.
|
|
|
Hello. Over the past few days 2 af my 3 my S9s has started acting strange. (been running fine for 4+ months) They start to mine slower after running some time, sometimes its hours sometimes minutes. I tried resetting them and also updated to latest firmware Antminer-S9-all-201704270135-autofreq-user-Update2UBI-NF.tar.gz. There is no known problems from bitmain that fits my problem. no ASCI errors, fans are running and all. one is 14T one is 13T model, i have another 13T that runs fine also upgraded to the same firmware. How do i make sure i used the right firmware and should have used the one with fixed freq? What am i missing?
|
|
|
I have 2 PCs with both 2x MSI RX vega 64 8GB both cannot use the blockchain driver, it shows grey artifactes on the whole screen on both PC, a few secunds after claymore miner starts. With only 1 card running there is no problem. Anyone have a fix for this?
I have the same problem too. Blockchain drivers is unusable, back to regular drivers. 2x vega 64 rig, 8gb ram, pentium g4560. Okay seems like the driver is the problem. Hope there is a new release comming
|
|
|
I have 2 PCs with both 2x MSI RX vega 64 8GB both cannot use the blockchain driver, it shows grey artifactes on the whole screen on both PC, a few secunds after claymore miner starts. With only 1 card running there is no problem. Anyone have a fix for this?
Did you overclock it at all? or just stock? 100% stock, newest gaming driver works fine also with OC in Wattman. But in wattman i can't under clock the gpu very much. and i only get 37 mh/sec @ mem at 1175
|
|
|
I have 2 PCs with both 2x MSI RX vega 64 8GB both cannot use the blockchain driver, it shows grey artifactes on the whole screen on both PC, a few secunds after claymore miner starts. With only 1 card running there is no problem. Anyone have a fix for this?
|
|
|
With the new beta driver is it still needed to copy files from an old version to get multi cards to work? i Have both RX480 and RX580 all bios modded, if that matters.
|
|
|
Why don't you just take out your sim card and put it into another compatible phone and then send the verification code to that phone. Then just put 2fa on whatever new phone you decide to get.
Not possible, the authenticator is on the phone and is not connected to the phone sim/number. I had to change password and reactivate my account, takes 48-72 hours. Really sucks.
|
|
|
Hi my phone was smashed and does not turn on anymore.
I need to disable it as my 2 factor so i can tranfer btc again. On the coinbase help its sayes this:
If you've lost the device with your Authenticator app and DO NOT have access to the secret seed code:
Select the "Unable to submit a one time code?" link in the after providing your username and password.
Note that this must be done on the Coinbase website, not the mobile application.
Once completed, the Authenticator app will be disabled on your account and you will receive 2FA codes by SMS to your verified phone number.
Note: If you do not get this prompt for a code after providing your email address and password, try logging in on an Incognito browser or clearing your cache and trying again.
But where do i find: "Select the "Unable to submit a one time code?" link in the after providing your username and password."
|
|
|
Hi my phone was smashed and does not turn on anymore.
I need to disable it as my 2 factor so i can tranfer btc again. On the coinbase help its sayes this:
If you've lost the device with your Authenticator app and DO NOT have access to the secret seed code:
Select the "Unable to submit a one time code?" link in the after providing your username and password.
Note that this must be done on the Coinbase website, not the mobile application.
Once completed, the Authenticator app will be disabled on your account and you will receive 2FA codes by SMS to your verified phone number.
Note: If you do not get this prompt for a code after providing your email address and password, try logging in on an Incognito browser or clearing your cache and trying again.
But where do i find: "Select the "Unable to submit a one time code?" link in the after providing your username and password."
|
|
|
After upgrading to 9.7 miners stops reporting hashrate to the pool at random, anyone else seeing this?
|
|
|
Thank you both very much, you saved my day. I found it now and my cards are working.
|
|
|
Updated your BIOS?
Yep its updated. First thing i did, so not even sure if it was there before the update.
|
|
|
Bought this card as the Asus Prime Z270-P was out of stock. In the bios i can't find Above 4G decoding, so i guess i bought the wrong card for mining Any tips? Or get a new MB?
|
|
|
Where do we buy now that Coinbase is down? Only been using coinbase and mining till now.
|
|
|
Hi Claymore
When ethman is rebooting a miner sometimes it does not see it as running after the reboot. If i close ethman and reopen it sees it as running again.
Also when a miner is down or off the hashrate is still counted in the stats below.
Are these bugs or just happening for me?
|
|
|
I have some rigs without a screen/keyboard/mouse.When i use remote desktop MSI Afterburner shows all as 0 så i cant set the correct clock speeds for mem and gpu. Also setting it via. command -mclock and -cclock does not work. Is there another way?
|
|
|
How do i get the settings from ethman from 9.4 to 9.5? So i don't have to type all in again.
Setting? I just copy and paste the .bat file created ethman not ethminer, the remote manager.
|
|
|
|