Latest posts of: zeef

Show Posts
Pages: « 1 2 3 4 5 6 7 8 9 10 11 [12] 13 14 15 16 »

221

Alternate cryptocurrencies / Mining (Altcoins) / Re: My Asrock H110 Pro BTC+ caught fire

on: March 26, 2018, 12:08:07 AM

Quote from: Vann on March 24, 2018, 02:15:03 AM Quote from: sylabis on March 24, 2018, 01:45:09 AM Quote from: Vann on March 17, 2018, 12:19:16 AM Did some more research on the right way to configure a dual PSU setup. This Biostar 12 GPU dual PSU mining setup guide states: http://www.biostar.com.tw/app/kr/event/crypto_mining/page4_2.htm Quote *The power cable for riser card and power cable for graphics card must come from same power supply uint. Given Biostar makes mining motherboards, USB riser kits, GPU's and they also have a financial incentive not to warranty thiose products, I believe they have an objective view on how to setup dual power supplies correctly. So I accept powering the riser and GPU with the same PSU is the correct way. I just rewired the risers and cards on my rigs so that the riser and VGA power connector on the cards are on the same PSU. The power consumptin from both type of setups is the same. The same Biostar mining guide also says you should only use a max of 2 risers per PSU power cable. Quote Each power cable from power supply is limited to be connected to 2 graphics cards or 2 PCI-Ex16 riser cards. On a side note I want to say that I ran my dual and triple PSU rigs with all the risers connected to PSU that powers the motherboard and the secondary PSU only powering the VGA 6/8 pin power under a heavy dual mining load 24/7 for almost a year and nothing bad came from it and my rigs are very stable. But this is for a specific Biostar mining board. They are also suggesting to plug 2x molex connectors directly into the MB, which according to Viperguy is a big no no/ fire hazard. The molex connectors on the motherboard are for supplemental 12V power to PCI-E slots. Specifically when using unpowered risers so that you don't burn up the traces on the motherboard or the thin wires on the 24-pin ATX connector from pulling too much 12V power when mining with multiple cards. Powered risers don't pull 12V from the PCI-E slot, they get it from the power connector on the riser, so there is no need to use the PCI-E supplemental power molex connectors o the motherboard. You can plug in the PCI-E supplemental power molex connectors on the motherboard when using powered risers, but it really doesn't make a difference. https://www.youtube.com/watch?v=i8tSXTqJVxQ&feature=youtu.be&t=2026 As far as the power going from the motherboard to the riser, there is only 3.3V going from the motherboard PCI-E slot to the riser through the USB cable, whether the riser uses that or produces it's own 3.3V is debatable, but I now think connecting the power on the riser to the same PSU as the power to the 6/8 pin PCI-E connectors on the card is the correct way. With dual PSU rigs, BBT now also powers the risers with the same PSU as the 6/8-Pin connectors on the cards. https://www.youtube.com/watch?v=i8tSXTqJVxQ&feature=youtu.be&t=3799 What's also important when using two or more PSU's is they all share the same ground as motherboard. Using the ATX splitter cables joins the grounds automatically and all the PSU's turn on and off at the same time automatically. https://www.aliexpress.com/item/NOTAYO-30cm-24pin-ATX-Power-Supply-Adapter-Cable-Connector-for-Mining-24Pin-20-4pin-Dual-PSU/32827619053.html? So in biostar manual says to connect the riser and gpu power to the same psu. Right? "**The power cable for riser card and power cable for graphics card must come from same power supply uint." http://www.biostar.com.tw/app/kr/event/crypto_mining/page4_2.htm Regards

222

Alternate cryptocurrencies / Mining (Altcoins) / Re: [Cast XMR] high speed XMR/CryptoNight miner for RX Vega GPUs (2 KHash/s)

on: March 22, 2018, 06:05:52 PM

Quote from: glph3k on March 22, 2018, 04:01:54 PM Quote from: zeef on March 22, 2018, 03:49:43 PM How exactly --ratewatchdog works glph3k? It just compares the current hash rate with the average hash rate if it is below a certain threshold it resets the kernel for the affected GPU. It should be faster then a complete restart and if only some GPUs have an hash rate drop only those have to be reseted and it does not lose the current job state. The exact reason for a sudden hash rate drop is still to be found, but it seems to be rooted deep in the driver. I suspect that it has to do something with power level switichings (ACPI) or similar. Regards, glph3k Thanks for clarify, Just tested the function in Vega56 and worked good. But drivers are so buggy. Any plans for porting the cast-xmr for a more recent drivers without the losing of hasrate? In rx580 im with new drivers and the hashrate is the same as blockchain drivers (very similar), why in vegas is not possible? Regards

223

Alternate cryptocurrencies / Mining (Altcoins) / Re: [Cast XMR] high speed XMR/CryptoNight miner for RX Vega GPUs (2 KHash/s)

on: March 22, 2018, 03:49:43 PM

Quote from: glph3k on March 22, 2018, 01:04:43 PM Quote from: tf2addict on March 22, 2018, 07:02:33 AM Suddenly I can't mine Graft with my Vegas using Cast 0.9.0, it says rejected share - low difficulty. Tried two different pools. Is something broken? Use the option --algo=0 to force classic CryptoNight. Graft reports that it is Version 7, the flag which Monero uses for the upcomming switch to their new CryptoNight variant. Thanks glph3k, How exactly --ratewatchdog works glph3k? Regards

224

Alternate cryptocurrencies / Mining (Altcoins) / Re: [Cast XMR] high speed XMR/CryptoNight miner for RX Vega GPUs (2 KHash/s)

on: March 22, 2018, 03:34:21 PM

Hi, Cast XMR UI doesnt work properly mining GRAFT in 0_9_1 version, because ignore the --algo=0 Exist any thread for the Cast XMR UI? Regards

225

Alternate cryptocurrencies / Mining (Altcoins) / Re: Best USB WatchDog Mining Rig Resetter?

on: March 19, 2018, 07:33:56 PM

Hi folks, Which of this watchdogs do you recomend? https://www.gearbest.com/WatchDog-_gear/ it is necessary to conect the hdd leds to them? im thinking of this: https://www.gearbest.com/other-pc-parts/pp_1249275.html Regards

226

Alternate cryptocurrencies / Mining (Altcoins) / Re: Automatic Repair Solution

on: March 15, 2018, 04:38:50 PM

I have an monitor plugged (powered off) and now have no problem. I have before an dummy plug too. And the automatic repair solution problem was solved by: bcdedit /set {current} bootstatuspolicy ignoreallfailures bcdedit /set {default} bootstatuspolicy ignoreallfailures Thanks people

227

Alternate cryptocurrencies / Mining (Altcoins) / Re: ASrock H110 Pro BTC+ 13 GPU Board

on: March 11, 2018, 12:18:24 AM

Quote from: bigjee on March 10, 2018, 06:29:13 PM Quote from: Sledge0001 on March 10, 2018, 06:19:14 PM Try using the Onboard Graphics for the connection to your monitor. Set ALL PCI-E slots to Gen 1 Try to boot with the Single GPU ONLY plugged directly into the Motherboard. If that works its a faulty riser. If it doesn't then your Motherboard may be defective. Make sure you are supplying power to BOTH Molex plugs on the Motherboard. Hope this helps. Yup the onboard has been connected to the monitor from the very start. ive tried gen 1, 2 and auto. basic troubleshooting shows all slots work except long pcie slot. Anyone experienced this issue on their end? I had an similiar issue and was a bad riser. In this board the gen2 gives me more speed Regards

228

Alternate cryptocurrencies / Tokens (Altcoins) / Re: [ANN][ICO] GRAFT - Universal Payment Processing Network

on: March 10, 2018, 01:42:40 PM

Quote from: Bytem3 on March 10, 2018, 09:42:56 AM You can now add Graft (GRFT) to your CoinCodex portfolio! Nice

229

Alternate cryptocurrencies / Mining (Altcoins) / Re: Any word on amd vega hash rates?

on: March 09, 2018, 01:06:41 AM

Quote from: rednoW on March 08, 2018, 09:12:17 PM Quote from: zeef on March 08, 2018, 08:25:17 PM Hi Guys, Im new to vegas, Today i got mine (Vega 56). Can get 2000 hs in blockchaindrivers using cast_xmr miner. My question is if we can achieve the same performance using the new drivers and claymore gpu miner for example. Regards If you like recent drivers and claymore then better to mine neoscrypt Thanks, What coins you think have potentially? Regards

230

Alternate cryptocurrencies / Mining (Altcoins) / Re: Any word on amd vega hash rates?

on: March 08, 2018, 08:25:17 PM

Hi Guys, Im new to vegas, Today i got mine (Vega 56). Can get 2000 hs in blockchaindrivers using cast_xmr miner. My question is if we can achieve the same performance using the new drivers and claymore gpu miner for example. Regards

231

Alternate cryptocurrencies / Mining (Altcoins) / Re: Claymore's CryptoNote AMD GPU Miner v11.2

on: March 05, 2018, 02:18:56 AM

Hi guys, I have an rx580 4gb gigabyte aorus with hynix memory. I made the oneclickpatch 1.6.7 two months ago. 0 Problems. Everything ok. But today when i unintentionally click on reset functionatlity in afterburner or Overdriventool, the card get 960hs. So i think let me try to increase the freq of memory from 1750mhz to 1800 etc.. But changing up the memory clock doesnt increase anything.. And if i restart the amd gpu miner 11.2 with the default setting, the hash is not so high like was before restart, It only increase if i toggle between my setting to default. Could be a bug in miner? (i tested in amd gpu miner and in cast xmr) Never happend to me. So now i start with my settings, toggle to default and get more hash.. but...doesnt make anysense Smiley Huh i just uploaded an video of my problem on yotube: https://www.youtube.com/watch?v=Yj_dDd3-TZY Regards

232

Alternate cryptocurrencies / Mining (Altcoins) / Re: My RX580 Benchmarking and Results: 30.5Mh/s @ 77.5W (+ 1130MH/s Dcr w/ 125W)

on: March 05, 2018, 01:58:59 AM

Quote from: zeef on March 04, 2018, 12:58:28 AM Quote from: RYXES on March 04, 2018, 12:34:30 AM Quote from: zeef on March 03, 2018, 10:54:20 PM Hi guys, I have an rx580 4gb gigabyte aorus with hynix memory. I made the oneclickpatch 1.6.7 two months ago. 0 Problems. She is hashing in 860 - 880 range with this settings in afterburner: 950mv core -10 powerlimit coreclock 1150 memoryclock 2020mhz Everything ok. But today when i unintentionally click on reset functionatlity in afterburner, the card get 960hs. So i think let me try to increase the freq of memory from 1750mhz to 1800 etc.. But changing up the memory clock doesnt increase anything.. And if i restart the amd gpu miner 11.2 with the default setting, the hash is not so high like was before restart, It only increase if i toggle between my setting to default. Could be a bug in miner? (i tested in amd gpu miner and in cast xmr) Never happend to me. So now i start with my settings, toggle to default and get more hash.. but...doesnt make anysense Regards I prefer v10.0 personally. Are you with Windows OS? if so check that it has updated, if so that is probably why, its killed 90% of peoples mining rigs on Windows 10. just need to do a PC Reset to an earlier build. Should work. Hi, Windows 10, I blocked all the automatic updates. All my rigs run fine on windows 10 and in linux. My question is just curiosity, if someone had have this bug too I think its corellated with overclocking only... What are the advantages from an older version 10.0 ? Regards Hi guys, i just uploaded an video of my problem on yotube: https://www.youtube.com/watch?v=Yj_dDd3-TZY Regards

233

Alternate cryptocurrencies / Mining (Altcoins) / Re: My RX580 Benchmarking and Results: 30.5Mh/s @ 77.5W (+ 1130MH/s Dcr w/ 125W)

on: March 04, 2018, 12:58:28 AM

Quote from: RYXES on March 04, 2018, 12:34:30 AM Quote from: zeef on March 03, 2018, 10:54:20 PM Hi guys, I have an rx580 4gb gigabyte aorus with hynix memory. I made the oneclickpatch 1.6.7 two months ago. 0 Problems. She is hashing in 860 - 880 range with this settings in afterburner: 950mv core -10 powerlimit coreclock 1150 memoryclock 2020mhz Everything ok. But today when i unintentionally click on reset functionatlity in afterburner, the card get 960hs. So i think let me try to increase the freq of memory from 1750mhz to 1800 etc.. But changing up the memory clock doesnt increase anything.. And if i restart the amd gpu miner 11.2 with the default setting, the hash is not so high like was before restart, It only increase if i toggle between my setting to default. Could be a bug in miner? (i tested in amd gpu miner and in cast xmr) Never happend to me. So now i start with my settings, toggle to default and get more hash.. but...doesnt make anysense Regards I prefer v10.0 personally. Are you with Windows OS? if so check that it has updated, if so that is probably why, its killed 90% of peoples mining rigs on Windows 10. just need to do a PC Reset to an earlier build. Should work. Hi, Windows 10, I blocked all the automatic updates. All my rigs run fine on windows 10 and in linux. My question is just curiosity, if someone had have this bug too I think its corellated with overclocking only... What are the advantages from an older version 10.0 ? Regards

234

Alternate cryptocurrencies / Mining (Altcoins) / Re: My RX580 Benchmarking and Results: 30.5Mh/s @ 77.5W (+ 1130MH/s Dcr w/ 125W)

on: March 03, 2018, 10:54:20 PM

Hi guys, I have an rx580 4gb gigabyte aorus with hynix memory, running on windows 10. I made the oneclickpatch 1.6.7 two months ago. 0 Problems. She is hashing in 860 - 880 range with this settings in afterburner: 950mv core -10 powerlimit coreclock 1150 memoryclock 2020mhz Everything ok. But today when i unintentionally click on reset functionatlity in afterburner, the card get 960hs. So i think let me try to increase the freq of memory from 1750mhz to 1800 etc.. But changing up the memory clock doesnt increase anything.. And if i restart the amd gpu miner 11.2 with the default setting, the hash is not so high like was before restart, It only increase if i toggle between my setting to default. Could be a bug in miner? (i tested in amd gpu miner and in cast xmr) Never happend to me. So now i start with my settings, toggle to default and get more hash.. but...doesnt make anysense Regards

235

Alternate cryptocurrencies / Mining (Altcoins) / Re: [CMD] Miner Autorun (Watchdog) for Ewbf & Claymore & Dstm & CCminer & Bminer

on: February 27, 2018, 11:00:51 PM

Hi, Nice work on bat Im testing the functionality, but i have two doubts. If i want to add an backup pool i add this on Config_xClay: # =================================================== [Miner] # Set the main server mining command here to auto-create Clay_miner.bat file if it is missing or wrong. [keep default order] commandserver1=NsGpuCNMiner.exe -xpool stratum+tcp://eu.xxxxmine.graft.network:4444 -xwal xxxx -xpsw x -allpools 1 -tstop 80 -logfile miner.log -wd 0 # When the main server fails, ClayXMRautorun.bat will switch to the additional server below immediately. [in order] commandserver2=NsGpuCNMiner.exe -xpool stratum+tcp://pool.graftpool.online:4444 -xwal xxxx -xpsw x -allpools 1 -tstop 80 -logfile miner.log -wd 0 # Configure miner command here. Old Clay_miner.bat will be removed and a new one will be created with this value. [keep default order] internetcheck=1 required. # The default number of servers is 5, however, you can add or remove as many as you need. e.g. you can have servers 1 2 3 or you can have 1 2 3 4 5 6 7 8 9. There is no upper limit - e.g. you can have 1000 if you want. The minimum is 1. # =================================================== [Overclock program] But when for example i put purposely an error in my first server1, the program doesn t shift to commandserver2! Its ok my syntax? or have to change the ClayXMRautorun instead of Config_xClay.. Another thing is If i tried to change : # Set how many GPU devices are enabled. gpus=1 and have 8 gpus, doens t gives me any error too.. and why it comes with default valor of 0, and worked good with 0 value? Even if i have more gpus installed.. Regards

236

Alternate cryptocurrencies / Mining (Altcoins) / Re: [Cast XMR] high speed XMR/CryptoNight miner for RX Vega GPUs (2 KHash/s)

on: February 27, 2018, 02:11:21 AM

Quote from: xpulse on February 27, 2018, 01:20:04 AM Quote from: zeef on February 26, 2018, 07:56:27 PM Quote from: xpulse on February 25, 2018, 08:19:45 PM Need help... New Rig, new fresh Windows 10 Pro 1703 CPU - Ryzen 5 1600/8GB RAM 4 GPU's: 1 Vega Frontier, 3 Vega64 (ASUS+XFX). Blockchain drivers. Here is weird results: C:\Mining\cast_xmr-vega>cast_xmr-vega -S cryptonight.usa.nicehash.com:3355 -u xxx.amd -G 0,1,2,3 --fastjobswitch --forcecompute ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Cast XMR 0.8.5 CryptoNight mining optimized for AMD Radeon Vega GPUs Coded by [glph3k] for more info visit http://www.gandalph3000.com Donating 1.5% mining power to developer. Thanks. For current stats press 's' For seamless exit press 'q' ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ [15:12:58] Initializing GPU, loading kernel ... Fast job switching mode enabled. Detected OpenCL Platform: OpenCL 2.0 AMD-APP (2442.12) [Suspicious link removed]pute Driver detected. GPU0: gfx900 \| 64 Compute Units \| Memory (MB): 8176 GPU1: gfx901 \| 64 Compute Units \| Memory (MB): 16368 GPU2: gfx900 \| 64 Compute Units \| Memory (MB): 8176 GPU3: gfx901 \| 64 Compute Units \| Memory (MB): 8176 [15:13:00] Connecting to cryptonight.usa.nicehash.com:3355 ... [15:13:00] Connected to pool. [15:13:01] New job received. [15:13:01] Difficulty changed. Now: 200007. [15:13:14] GPU1 \| 51°C \| Fan 1024 RPM \| 287.1 H/s [15:13:16] GPU3 \| 38°C \| Fan 0 RPM \| 239.1 H/s [15:13:17] GPU2 \| 57°C \| Fan 1312 RPM \| 212.6 H/s [15:13:18] GPU0 \| 43°C \| Fan 4666 RPM \| 209.8 H/s [15:13:25] GPU1 \| 52°C \| Fan 1015 RPM \| 359.0 H/s [15:13:27] GPU3 \| 38°C \| Fan 0 RPM \| 312.0 H/s [15:13:35] New job received. Avg Job Time: 34.0 sec [15:13:35] GPU0 \| 45°C \| Fan 4668 RPM \| 158.9 H/s [15:13:35] GPU0: 28 ms needed to switch to new job [15:13:35] GPU3 \| 39°C \| Fan 0 RPM \| 357.4 H/s [15:13:35] GPU3: 36 ms needed to switch to new job [15:13:35] GPU1: 49 ms needed to switch to new job .... ETC Can someone have any idea, why hash soooo looooow... Thanks. Have you enable the compute option in wattman? There is no compute option in wattman, also because 1 of the card is Vega FE wattman even not showed up. I was in blockchain drivers too in my rig of 10 rx580 since january!! I change to last one amd 18.2.3. And i recommend a lot!! Real stable and the hashrate is the same, no errors at all. In vega i dont test. Im waiting for my to come from amazon to test But give it a try and test the compute mode in new drivers. Old blockchain (have compute mode by default). Try to find the Vega Thread in this site forum too and as...

237

Alternate cryptocurrencies / Mining (Altcoins) / Re: [Cast XMR] high speed XMR/CryptoNight miner for RX Vega GPUs (2 KHash/s)

on: February 26, 2018, 07:56:27 PM

Quote from: xpulse on February 25, 2018, 08:19:45 PM Need help... New Rig, new fresh Windows 10 Pro 1703 CPU - Ryzen 5 1600/8GB RAM 4 GPU's: 1 Vega Frontier, 3 Vega64 (ASUS+XFX). Blockchain drivers. Here is weird results: C:\Mining\cast_xmr-vega>cast_xmr-vega -S cryptonight.usa.nicehash.com:3355 -u xxx.amd -G 0,1,2,3 --fastjobswitch --forcecompute ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Cast XMR 0.8.5 CryptoNight mining optimized for AMD Radeon Vega GPUs Coded by [glph3k] for more info visit http://www.gandalph3000.com Donating 1.5% mining power to developer. Thanks. For current stats press 's' For seamless exit press 'q' ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ [15:12:58] Initializing GPU, loading kernel ... Fast job switching mode enabled. Detected OpenCL Platform: OpenCL 2.0 AMD-APP (2442.12) [Suspicious link removed]pute Driver detected. GPU0: gfx900 \| 64 Compute Units \| Memory (MB): 8176 GPU1: gfx901 \| 64 Compute Units \| Memory (MB): 16368 GPU2: gfx900 \| 64 Compute Units \| Memory (MB): 8176 GPU3: gfx901 \| 64 Compute Units \| Memory (MB): 8176 [15:13:00] Connecting to cryptonight.usa.nicehash.com:3355 ... [15:13:00] Connected to pool. [15:13:01] New job received. [15:13:01] Difficulty changed. Now: 200007. [15:13:14] GPU1 \| 51°C \| Fan 1024 RPM \| 287.1 H/s [15:13:16] GPU3 \| 38°C \| Fan 0 RPM \| 239.1 H/s [15:13:17] GPU2 \| 57°C \| Fan 1312 RPM \| 212.6 H/s [15:13:18] GPU0 \| 43°C \| Fan 4666 RPM \| 209.8 H/s [15:13:25] GPU1 \| 52°C \| Fan 1015 RPM \| 359.0 H/s [15:13:27] GPU3 \| 38°C \| Fan 0 RPM \| 312.0 H/s [15:13:35] New job received. Avg Job Time: 34.0 sec [15:13:35] GPU0 \| 45°C \| Fan 4668 RPM \| 158.9 H/s [15:13:35] GPU0: 28 ms needed to switch to new job [15:13:35] GPU3 \| 39°C \| Fan 0 RPM \| 357.4 H/s [15:13:35] GPU3: 36 ms needed to switch to new job [15:13:35] GPU1: 49 ms needed to switch to new job [15:13:35] GPU1 \| 51°C \| Fan 1016 RPM \| 325.4 H/s [15:13:35] GPU2: 135 ms needed to switch to new job [15:13:35] GPU2 \| 56°C \| Fan 1324 RPM \| 155.9 H/s [15:13:50] New job received. Avg Job Time: 25.0 sec [15:13:50] GPU1: 67 ms needed to switch to new job [15:13:50] GPU1 \| 51°C \| Fan 1010 RPM \| 126.7 H/s [15:13:50] GPU0: 151 ms needed to switch to new job [15:13:50] GPU0 \| 46°C \| Fan 4680 RPM \| 113.7 H/s [15:13:50] GPU2: 172 ms needed to switch to new job [15:13:50] GPU2 \| 55°C \| Fan 1325 RPM \| 114.3 H/s [15:13:50] GPU3: 200 ms needed to switch to new job [15:13:50] GPU3 \| 38°C \| Fan 0 RPM \| 113.4 H/s [15:13:54] New job received. Avg Job Time: 18.0 sec [15:13:54] GPU0: 53 ms needed to switch to new job [15:13:54] GPU2: 72 ms needed to switch to new job [15:13:54] GPU3: 138 ms needed to switch to new job [15:13:54] GPU1: 205 ms needed to switch to new job [15:13:54] GPU1 \| 52°C \| Fan 1015 RPM \| 472.3 H/s [15:14:10] GPU1 \| 51°C \| Fan 1020 RPM \| 189.4 H/s [15:14:11] GPU2 \| 56°C \| Fan 1316 RPM \| 212.8 H/s [15:14:12] GPU3 \| 38°C \| Fan 0 RPM \| 211.8 H/s [15:14:12] GPU0 \| 45°C \| Fan 4681 RPM \| 209.8 H/s [15:14:26] GPU1 \| 51°C \| Fan 1014 RPM \| 244.1 H/s [15:14:29] GPU2 \| 55°C \| Fan 1324 RPM \| 198.9 H/s [15:14:29] GPU3 \| 38°C \| Fan 0 RPM \| 199.4 H/s [15:14:30] GPU0 \| 45°C \| Fan 4682 RPM \| 198.3 H/s [15:14:45] GPU1 \| 51°C \| Fan 1019 RPM \| 210.8 H/s [15:14:48] GPU2 \| 55°C \| Fan 1320 RPM \| 194.6 H/s [15:14:48] GPU3 \| 38°C \| Fan 0 RPM \| 193.4 H/s [15:14:49] GPU0 \| 45°C \| Fan 4671 RPM \| 189.7 H/s .... ETC Can someone have any idea, why hash soooo looooow... Thanks. Have you enable the compute option in wattman?

238

Alternate cryptocurrencies / Mining (Altcoins) / Re: Claymore's CryptoNote AMD GPU Miner v11.2

on: February 19, 2018, 02:36:56 AM

Hi Guys, What means : Pool switches: XMR - 3 ? Regards

239

Alternate cryptocurrencies / Mining (Altcoins) / Re: [Cast XMR] high speed XMR/CryptoNight miner for RX Vega GPUs (2 KHash/s)

on: February 12, 2018, 02:58:49 AM

Quote from: FgTeamBR on February 12, 2018, 02:56:06 AM shorcut 1 to start gpu 1 TIMEOUT /t 5 cast_xmr-vega -S etn-us-west1.nanopool.org:13333 -u G 0 shortcut 2 without timeout to start gpu 2 cast_xmr-vega -S etn-us-west1.nanopool.org:13333 -u G 1 copy 2 shorcut from desktop and past in startup folder. ahh yeah will work But i want my code to work too ehehhe

240

Alternate cryptocurrencies / Mining (Altcoins) / Re: [Cast XMR] high speed XMR/CryptoNight miner for RX Vega GPUs (2 KHash/s)

on: February 12, 2018, 02:52:57 AM

Quote from: FgTeamBR on February 12, 2018, 02:50:20 AM Quote from: zeef on February 12, 2018, 02:27:46 AM Quote from: FgTeamBR on February 12, 2018, 02:25:07 AM Quote from: zeef on February 12, 2018, 02:21:41 AM Hi guys, Anyone know how to make an .bat file to open the cast xmr vega. I want to add it to startup folder. Im trying this .bat, but doesn t work: cmd /k "cd /d D:\partilhada\Mining\Miners\xmrvega\" start_graft.bat But Get stucked in the directory Thanks just creat an shortcut of bat and past this copy in to the startup folder Hi , This form i know, But if i want to call another instance of other program with some delay.. i want flexibility create 2 shortcut for 2 diff instance and past TIMEOUT /t 5 before cmd line GG TIMEOUT /t 5 in one of these obviously Hi, Thanks for anwser, Can you examplify Im almost there: cmd /k "cd /d D:\partilhada\Mining\Miners\xmrvega\" - this apoints to directory but now i cant start the bat.. i will make ittt Thanks

Pages: « 1 2 3 4 5 6 7 8 9 10 11 [12] 13 14 15 16 »