Кто нибудь попробовал на VDD и IOVDD подавать одно и то же напрежение, будет работать или IOVDD должно быть выше?
А зачем? У Вас проблемы со стабилизатором на 1.8В? Вряд ли чипу хватит половины от требуемого напряжения.
Лучше одинаковое на VDD и IOREF.
|
|
|
Че 28nm замутили? $8 за гигахеш?
|
|
|
DDN то говорил что они ему встали по 36, не знаю на сколько конечно это правда Так что думаю дешевле 50 точно не стоит ждать
Мне отписал что по $54 встали. Это соответствовало ценам в магазине у пунина. 50TH это 20000 чипов. Врядли битфури успел распаять столько. Думаю кто-то троллит.
|
|
|
Куплю 16 штук по $15
Куплю 16 штук по $14.
|
|
|
Is that possible to withdraw USD from BTC-E to PayPal accout? I saw on bitcoinwiki that PayPal is supported.
It is, not sure why people are saying it isnt. If you go to your finances, and hit the Withdraw button next to USD, you can withdraw to Paypal. There is a 6% fee however and a minimum transaction amount ($250). In the field that says "Purse" you enter your Paypal Email address, and they send the $. I've gone that route before, and the first time to withdraw, it takes like 12 hours, although I believe BTC-E says that you may have to wait for 24 hours. After your first withdraw, it goes a bit faster. Something about them making sure you aren't on a Paypal blacklist. Thanks SaltySpitoon. I will try this as soon as possible. The btc support told me there are no problem with PayPal. The only thing i'm not sure is that i will be able to use the money after 24h. PayPal requires to hold money for a 45 days in the case of chargeback.
|
|
|
Скажите насколько безопасен вывод на PayPal? Вроде не сразу можно деньги со счета использовать?
|
|
|
Is that possible to withdraw USD from BTC-E to PayPal accout? I saw on bitcoinwiki that PayPal is supported.
|
|
|
После суток работы скорость начала падать. Пруф.
|
|
|
Это цитата одного чувака с форума. Вот думаю может у них скорость 400 девайсов в сутки но правда много заказов было в первые дни. Хотя верится с трудом.
Крутятся мысли взять рефанд через paypal. И вложиться в битфурия.
|
|
|
Sorry but I have to post again just to air my frustration with some people, I can see looking through the forums here that most people ordered in the wee opening days. If you consider that perhaps 75% of the total orders outstanding where ordered in the first 2 months of opening orders, then, you can only come to the conclusion that the further through the dates they get the faster the progress will be. I understand that you are frustrated but you have to try to be patient, your orders will no doubt be shipping pretty soon. Peace out.
|
|
|
dimitrus у тебя есть возможность замерить клок на чипе? Дело в том что меандр это 23 бит nonce счетчика. Поскольку перебор происходит за 65 клоков то соответственно клок делится на 545259520. Можешь проверить это? Это пока не проверенная информация. Подозреваю что едининца в меандре означает завершение перебора и говорит о готовности результата.
|
|
|
t309 вот ты уверен что два слоя достаточно для 8 чипов? Токи всетаки приличные. Голландцы сделали 4 слоя.
многослойку не делают за 3 дня ето раз, голандцы если ето плата на 16 чипов фотки которой всюду светились бездаори в плане дизайна а бездарям ничего не остается кроме как компенсировать качество количеством, а хватит или нет будет видно и уже скоро Да я имею ввиду именно это плату. Мне показалось что не очень место оптимально используется. С другой стороны там под возвратный ток много места. Сам хочу сделать двухслойку на 16 чипов. Надеюсь у тебя заработает.
|
|
|
t309 вот ты уверен что два слоя достаточно для 8 чипов? Токи всетаки приличные. Голландцы сделали 4 слоя.
|
|
|
Вопрос топикстартеру. А сколько слоев у платы?
|
|
|
Thanks for reply. I made a simple board for one chip. And it is ok. I want to build something similar. I think you have the following layer stack:
top - power plane and jumpers (if any chip will be damaged) layer1 - Ground and SPI connection between chips layer2 - Ground and IOVDD conection bottom - Ground plane
Am i correct?
A small board with a single bitfury can be a bi-layer indeed. Wouldn't take changes when making a board with many ASICs Here you can see the different layers: Layer top is Vcore (0V6..0V9), rest is GND with vertical going wires on layer 3 and horizontal going wires going on layer 2. Except near the upper edge were current density is low. Layer bottom is also GND. In the power section layer top is also GND. intron Thanks intron for sharing the board layers. It is not very clear how do you connect the grounds together. As i understand the chips 49 pin (GND) is connected to the blue (lowest ground). Also the capacitors near the chips goes to the lowest ground. Am i correct? There are also a lot of vertical vias. Do they connect the yellow and green grounds?
|
|
|
это сколько чипов?
все ок, скорость в цгмайнере и на пуле тютя в тютю 1:1 ето 4 чипа Помайни пару дней. Не вырубай.
|
|
|
t309 ты на каком пуле майнишь? У тебя сходиться скорость в cgminer и количество шар (выплат) в статистике пула. У меня вот на 50btc по шарам в два раза меньше выходит иногда.
|
|
|
Задал вопрос cscape который писал прошивку. Вот его ответ: I just read the chip periodically to see if job is ready. About 4-5x per second seems to work good enough.
I haven't watched the inmiso pin. I'll check that out.
I noticed that at beginning the chip is rather erratic and producing a lot of duplicate results. Only after cycling through 16 word buffer at least once, will it stabilize. Maybe that is what you are seeing. How long does your 'high speed' phase last ?
PS: bitfury на вопрос о меандре ответил что не знает что это такое. PSS: Что такое high speed phase и какая у нее длительность?
|
|
|
|