I have a burnt pcb too but mine can still work. I fix back in leaving a small gag without touching the heatsink. I suspect that burnt portion is cause by the heatsink. The temp should be around. 48 to 58'c no more than. 59 Put a box fan or household fan right in front of the coincraftdesk where they are sucking the air . It shild be stable when. You got your replacement.
|
|
|
Oh bad news for all of us, who is saving btc to buy anther pairs!!!! Bitmain can you extend the sale for another 5 weeks?
|
|
|
Check the sd card take out and inset again or get a new sd card and burn a new firmware from Bitmine
|
|
|
Is someboby have teamviewer To make it for me ? I'm not able to set my configuration ? I unplugged the antminer from the router than plug into my pc to setting up but nothing at all??? that's piss me off !!!! I hate network lol my email is neptune748@hotmail.com For those first timer S1 setup who are facing problems...... 1) switch on the s1 2) locate the reset button, the. Tiny button. Reset it 3) after resetting is completed, then turn off the s1 from the psu. Wait for awhile like 40 second or more. 4) connect the cable s1 to the router as usual, power on then hit 192.168.1.99 at the ie or Firefox. See if you can log into the s1 setting. Good Luck.
|
|
|
read few posts back
bro what's the fan size?
|
|
|
A few post back from Bitmine ok. Did u use Ny fan controller or just the fan?
|
|
|
Wow 3000 rpm where did u buy from?
|
|
|
Nope , can u take a photo of your desk I wana see how you place it
|
|
|
My desk temperature is 62.c. And there are 2 sparks happened minor spark becos. I saw the flashing spark. Not sure the module near the psu or the red plate or something else. What's the normal tem ?
|
|
|
If you select failover and click submit, it resets to balance but it works as failover. Check your pool and you will see.
Hi can put a link for downloading the firmware for the coincraft desk that comes with the shippment. Thanks a lot bro. http://bitmine.ch/?page_id=5517Thanks you bro. Wish that I can buy from you , keep your option open
|
|
|
Thanks for the support Giorgio n Christine , I need to sleep first .
I havie been reading the forums and sorry to hear the delay to other customer I am one of them too. If u are still waiting maybe you ask them to ship without the power supply . This will be much faster.
For those who are waiting for the rigs , maybe you wana convert to desk? Since the rig is almost ready for production soon. Wait alittle bit.
I see a handful of you got the refund well good on you. but, think again if this were BFL or HF you won't your money for anther 9 months or longer or worst, nerver!
Bitmine is catching up their orders and that's is for sure.
|
|
|
If you select failover and click submit, it resets to balance but it works as failover. Check your pool and you will see.
Hi can put a link for downloading the firmware for the coincraft desk that comes with the shippment. Thanks a lot bro.
|
|
|
so i test the new clocking options, these are the results that i get:
power save ultra ~710 Watt = ~740 GH/s 0,95 Watt per GH/s
power save moderate ~770 Watt = ~808 GH/s ~0,95 Watt per GH/s
power save light ~940 Watt = ~940 GH/s ~1 Watt per GH/s
normale mode ~1040 Watt = ~1020 GH/s ~1,01 Watt per GH/s
turbo light ~1140 Watt = ~1080 GH/s ~1,05 Watt per GH/s
turbo moderate ~1330 Watt = ~1140 GH/s ~1,16 Watt per GH/s
turbo extreme not testet, because the system starts for a second and than go down... i think it can be a problem with the psu, i musst test it
the HW in alls mode are under 1 % -> i get this result with the tool "cgremote"...
Thank you Wolke for this detailed report, can you tell me what PSU do you have mounted in the unit? hehe no problem...i was interested what is possible.... i bought the psu's from LEPA -> G1600-MA-EU ( http://www.lepatek.de/g1600/ ), i bought it because i get this psu for a special price, i paid only 219 € inkl. tax for each... Ok, the PSU looks good in wattage but possibly you have not equally distributed the 12V rails available on the 5 slots. Can you please make sure from the manufacturer's manual that each card would be able to get up to 30-35A each? Sorry is there a link for the web interface firware, cos I cannot access the nterface with the sd card, I. Might have to burn a new sd card.
|
|
|
Sorry I just mess up the ip and I cannot access the web . I try to connect directly to the pc but no go. Where can I download a new firmware and load into the new sd card or how? Pls help thanks
|
|
|
is s1 still available? and do you ship internationally?
Hello Guys, So far its been a 12+ hour work day. I've been answering customer emails, calling people, texting. I have ~40 Antminer S1 that I unboxed last week for my personal mine. They are in perfect condition, but I will sell them as new-used. Due to high demand the price stays at 0.893 but you get free shipping unless you pay expedited. I am looking to get rid of 30 or so of them. Please email or goto the store...i'm off to the gym to take care of my health Please support NinjaTech Very Respectfully, GreaterNinja So the expedited pay is 0.988? Within 3 to 5 day shippment time? To asia?
|
|
|
Thanks Giorgiomassa, but I like to know what happened to my ship, I was told would be sent in the first week of April and still have not had any mail from you.
My order is 298x, please thank you to tell me whether or not sent this week and I start to get tired of waiting.
Me too my is on the second week April order 36xx. Thank the the update anyway.
|
|
|
Giorg how about switching all shippment to UPS?
|
|
|
As I said, they're not runnig at my home. But I'll ask my friend for some screenshots... But first he has some problems to solve...according to eligius.st the two miners deliver only 377 Gh/s. At ghash.io it was around 600 Gh/s....which is very strange. There are no HW errors and they should deliver at least 1200 Gh/s :/
CONGRATS . Vidoe please . No rushing take your time,
|
|
|
My miners arrived today 2x 1th/s desk and 1x200gh/s desk running @ ~2.4 th/s (40-45°C,nominal) Happi for you
|
|
|
They are clearing the Q why not wait a little bit longer.
|
|
|
|