It seems that the temp sensor is reading abnormal or it is broken.

Have you tried to flash it? If not then try it first then try to test the hashboard one by one

Also, a little bit of research here on the forum will bring you here https://bitcointalk.org/index.php?topic=5244120.0
Reading that would help you to get rid of the sensor problem.

I tried to check that but mine shows different look at the image below



And it seems they only have limited supported devices look



So based on that image only one Huawei model is supported.

Why not just import it manually? If you don't have much seed to check then just manually import it to Electrum to check if it has a balance.
You can import multiple times in Electrum so it should be easier than to make a script to automate seed checking.

Be careful on the tool that I found on Google "Cybercoplabs" I never heard of this site but I saw this site when searching about "Seed checker". The website looks the same as iancoleman tool so it's not a checker that I think you looking for?

I think they need to add a new rule about making a post like that because I saw many posts these days copy/pasted with a source link and they are now spreading.
It's doesn't have any effort and no value unless if they added some of their own words before they copy/paste including the source link.

I know spammers change their strategy due to plagiarism at least we already see the effect of banning those who copying and pasting from another source. Now they are copying and include the source link which is still annoying.

Do you have other software installed like deep freeze that could revert back to its original state every time you restart the PC?

If not then you might do wrong when installing the latest version, make sure that you close the Bitcoin core 0.17 and completely shut it down before you proceed to install the latest version.

If you did that already but it still downgraded to 0.17 there might be a system error from your PC that could revert back Bitcoin core to the old version.

Based on what I understand it has 9 deleted posts but in his own posts not posts by other users.

Unless if he deleted other user's posts from his own thread so it would count by 1 or more.

This section is for Bitcoin mining not for altcoin mining but I will give you a site for "Asic Miner Repair Service Centre"

Check it here https://www.zeusbtc.com/Repair.asp
Scroll down and you should see the US Repair shop.

It would be considered illegal if you include the "illegal way".

I would suggest you better sell it on other websites if you want to stay here
And read our forum rules here https://bitcointalk.org/index.php?topic=703657.0

Take note of this


I think he uses a Linux OS to detect the control board but try the commands above under #3 read that part.

Well, there's nothing we can do only a few users use ASIC hiveOS and I believe that you can connect s9 miner on their dashboard without flashing it with their firmware.
What I think is if you don't have a remaining balance on HiveOS to pay monthly their pricing for ASIC is around $2/mo per ASICminer so they might be stealing a few hash rates as a monthly payment. This is just what I think but I don't know actually how they work.

If you want an accurate solution it would be better if you bring your issue to their own forum they have their own forum and I'm sure you will get a better answer.
Here's the link: https://forum.hiveos.farm/

Can you check your Bitcoin core is fully sync? Armory wallet won't work properly if the Bitcoin core is not fully synced and also Armory won't run properly if your bitcoin core is in pruned mode. So check that first on the bitcoin core settings and untick prune.

Then let's see if it will sync again or if it was fully synced?

---

This issue shouldn't take too long if you export the private key and import it to Electrum and transfer the remaining bitcoin to another wallet and then start again on the installation of your Armory and Bitcoin core wallet before you sent it back to your new armory wallet.

Is this an android issue on your side?

Have you tried to use a dedicated proxy instead and manually set up your Android device with that proxy and test it again if it will automatically disable the proxy?
If it PC/Laptop do the same setup the proxy manually.

If nothing works then try the solution from this link below.
- https://support.exodus.com/article/59-i-get-an-error-message-can-not-connect-to-p2p-network

If the pool doesn't show any problem why not just ignore it?

It might be a bug on their side or the firmware you installed in your miner is corrupted?

Why not try to reflash the miner with that firmware again and test it again. Also, replug all ethernet cables on that miner the ethernet cable is not plugged properly.

ASIC miner doesn't need any software it's a plug-and-play, you just need to set up the pool you like.

I hope that you read the sticky thread under this section before you post.

Read this First time/Small miner reference for getting started.
It should answer all of your needs.

If you are sure that it was the same seed then your problem is the right derivation path.
I would suggest you import it on Electrum already suggested above but this time you will need the xPub or zPub under wallet>information you will need to analyze it using xPub analyzer.
Here's the tool https://blockpath.com/wallets/new?action=appxpub

Then paste the xPub or zPub of your wallet then scan all, if the tool found used addresses with balances you will see the derivation path on the left side use it to find the exact derivation path of your wallet.

Can you try to access your account and withdraw them through incognito mode or use other browsers instead?
It might be a browser issue clearing the cache might help if not then it is a server issue from their side.

I would suggest you contact them from their telegram here https://t.me/localethereumdotcom then report the issue.

Are you sure that you use 3.3.8 for almost 5 years? This version was released 2 years ago or according to GitHub Jul 11, 2019 so it's impossible that you use a 3.3.8 5 years ago.
Unless if it's a fake one.

I would suggest you backup everything first the wallet file or seed phrase before you uninstall the 3.3.8 and don't upgrade just install the latest version.

So your problem is your miner can't connect to the router?

If you already factory reset the miner and it still can't show the IP in your router try to flash the unit through an SD card.

You can follow the guide from this link
- s17 pro control board program recovery

And then use the SD card firmware from this link "S17 pro SD card firmware"

After that use the software provided by Bitmain to find the IP of your miner.
Download it here APMinerTool
That would help to scan the IP of your miner.

The other question you had we will answer it later after you solve the first issue. Take note ASICboost firmware is power-efficient firmware.

This one is your problem ViaBTC pool is different from F2pool you won't get any reward on F2pool by mining on ViaBTC pool you should see a reward in your own ViaBTC pool account.

Make an account on ViaBTC pool if you don't have yet and then log in after you login scroll down and follow the guide on how to set up the pool of your miner. Just follow them don't customize it to your custom name so that we can check if the default config is working.

Which one actually do you want to decrypt? The wallet or the Electrum software?

If you talking about Decrypting the Electrum software why not go to their open-source https://github.com/spesmilo/electrum
Then you can develop it with your own utility that you want to add.

Or are talking about the wallet file or wallet.dat with a password?

There is a way to brute-force it but without the portion of the password or seed phrase it will take years before you can recover your password or wallet.