It is not revolutionary at all. It is power hungry and expensive.
20GHs Asic 28nm = 30W at the wall (max) 20Ghs Cloud Mining X 0,0339 = 0,678 BTC or 542 USD. And is available now.
And of course FGPA is an old story!!! So, where is the Revolution???
Δεν υπάρχει επανάσταση αδελφέ μην το ψάχνεις. Τα συγκεγκριμενα τσιπάκια/modules είναι της gridseed και τα αγοράζεις με $2K για 10, αλλά πάλι εξαιρετικά ακριβά. Αφού αγοράζεις μια antminer με $1200 που σου βγαζει περισσοτερά γιατί να ασχοληθείς?
|
|
|
i also get pretty much from whatever mining happens at the 2nd and 3rd pool options set on the ant, is this normal?
Do not set the secondary and third pools. If there is any network delay it is going to flip over super fast and you might get rejects and stales. This was messing me up big time at first until I just set a primary and blanked out the rest. you could be right, since i get nothing in the those two anyway Actually I had a problem when I set pool 2 and 3. When I removed them and stuck to just one pool everything is working fine.
|
|
|
That is the stratum difficulty he has set.
16+ GH/s - 16 difficulty 32+ Gh/s - 32 difficulty 64+ GH/s - 64 difficulty 128+ GH/s - 128 difficulty 256+ GH/s - 256 difficulty 512+ GH/s - 512 difficulty 1 TH/s - 1024 difficulty
where exactly do you set these values? what happens if they are not set to match the miners operating speed? Trust me I get an average of 0.003% score no matter the difficulty set. However I have noticed slight increases of GH speed after the change from 16 to 128 workers. Bottomline: I get more or less the same score, sometimes higher but sometimes less. EDIT: You set them from your profile setting under mining I see it on 128 on my miner status page but where do you change it from. NOt that From cex.io click on your account name and choose profile -> mining settings
|
|
|
I am having a problem checking out with an order on the website today. Anybody know when this will be resolved? Thanks I heard of a few people who tried to access their site yesterday and today and had problems. I would wait until the issue is resolved.
|
|
|
That is the stratum difficulty he has set.
16+ GH/s - 16 difficulty 32+ Gh/s - 32 difficulty 64+ GH/s - 64 difficulty 128+ GH/s - 128 difficulty 256+ GH/s - 256 difficulty 512+ GH/s - 512 difficulty 1 TH/s - 1024 difficulty
where exactly do you set these values? what happens if they are not set to match the miners operating speed? Trust me I get an average of 0.003% score no matter the difficulty set. However I have noticed slight increases of GH speed after the change from 16 to 128 workers. Bottomline: I get more or less the same score, sometimes higher but sometimes less. EDIT: You set them from your profile setting under mining
|
|
|
i have a problem, and i wonder if anyone got the same issue after 2 days of mining i start to get errors on both miners 2 antiminers s1: ooxxxooo oxoxoxxo oooxoooo oxxooooo
On BTC Guild, i have the same hash rate.
After a reboot, the errors goes away, and i can mine again for 2 days or so...
Ignore them it is just a display bug. I agree. If your hashrates are fine the X does not mean anything. However if you keep getting that error check your PSU. That error is listed in the antiminer setup and troubleshoot guide: https://bitcointalk.org/index.php?topic=344970.0
|
|
|
I am some what known in the community, I've been interviewed for international newspapers, more than once now......
I would be more than willing to test one of these, Please contact me. If you have interest in testing still
I am more or less unknown to the community, I have never been interviewed by international newspapers, not once now.... I am definitely interested in testing one (or more) of these but I know I will never get the chance to unless I buy one. But I am feeling lucky (and a but tipsy) so I thought I would give it a shot too Besides, why not get a review from a "newbie" as well as a detailed description of how good and easy to work with your miners are. Think about it.....
|
|
|
Your score is just a percentage of the entire pool, everything is fine. Stop worrying Got it Thanks
|
|
|
Ok guys I have asked this question before but got no response so I decided to show you what I mean: Any explanation from the Antminer gurus why my NOT OVERCLOCKED Antminer hits these speeds? I am not saying I am not happy but, Is this going to cause a problem to my miner? Please let me know. Thank you Look at the average rather than the current speed and it shows to be running at good speed. It will go up and down due to pool or even internet connection but as long as you are happy with the speeds and there is no x's on the chips then you are all good. Which chip sped are you currently on ? Just to double check 375 is default What do u mean chip speed? I did not overclock. The only modification I did was to disable NTPD as I was getting errors and wouldn't connect. Also if you notice, apart from the speeds my score is usually the same, sometimes it goes higher to 0.004 but also down to 0.002 Most pools calculate your speed based on submitted shares and some specific time (usually 30-60 minutes) and that's what it shows. look at your 1day average that's closer to true speed. Also if you look at you antminter directly it will show you your current hushing speed and average that's closer to its current performance. i can tell you...this is nothing!!! i run 150gh and it begin almost every round with more than 1TH.... no joke...artially held it continuously for more than 500 almost the hole 6min round... OK, but is your score the same as mine, between 0.002-0.005%? I think that's what matters.
|
|
|
I'm willing to 500€ worth total shipped to italy, pm me if it's possible
If they actually offer that price count me in for 3 at least!
|
|
|
Why do you think they are in stock and dropping on price constantly?
None of the antminers I've received showed the slightest evidence of being used. The reason they are dropping prices is that they're selling these things near or beyond the boundary of profitability, and so as more hashrate increasing days go by they need to lower the price to keep it from being an obvious loss to everyone. My miner didn't show signs of being used either, and I am planning of ordering more. Don't get me wrong but I am not stupid. And when this guy: http://eligius.st/~wizkid057/newstats/userstats.php/1Nbq2XZaRsKknf5fcT2wTXvBS31PaUWSeXHad a mining power of 252TH 2 weeks from now, 2 days from now more than 520TH and today only 450TH (btw 3 hours before it was 490), then don't tell me pre-order or any kind of mining equipment has not been used yet. For the sake of testing purposes let's say Let's be honest here, it's nothing personal it's just business. You would have done the same.
|
|
|
Nothing new released yet.
They are selling the Antminers to make room for the 2TH+ miners Why do you think they are in stock and dropping on price constantly?
|
|
|
hahahaah .. +1
|
|
|
OK, so I guess I shouldn't worry about my miner as I have it on a 500w PSU. Thanks guys
|
|
|
That is not even a 3D graphic, its a pseudo-3D graphic.
hahahahaha
If you were really designing this the you would have a true 3D perspective of your machine.
Sorry I don't buy.
Besides, 3MH for $2500 when you can get the from the MANUFACTURER for $2K?
And $2K for a machine like that is way too much at this point.
|
|
|
Ok guys I have asked this question before but got no response so I decided to show you what I mean: Any explanation from the Antminer gurus why my NOT OVERCLOCKED Antminer hits these speeds? I am not saying I am not happy but, Is this going to cause a problem to my miner? Please let me know. Thank you Look at the average rather than the current speed and it shows to be running at good speed. It will go up and down due to pool or even internet connection but as long as you are happy with the speeds and there is no x's on the chips then you are all good. Which chip sped are you currently on ? Just to double check 375 is default What do u mean chip speed? I did not overclock. The only modification I did was to disable NTPD as I was getting errors and wouldn't connect. Also if you notice, apart from the speeds my score is usually the same, sometimes it goes higher to 0.004 but also down to 0.002
|
|
|
interesting! i looking for news! Indeed! Me too
|
|
|
Any idea of when we can expect your license release? Are any of your prototypes working? Thanks Look at the update just a few posts back gives you general idea where we are. Still waiting on an initial bring up board for the BitFury Wasp. We will release licensing at the same time the gerbers, bom, software, firmware and hardware are working and we will know better on that come the meeting on Saturday. A1/BitMain and BitFury Wasps release would come out nearly together if not together and we are hoping for better news this Saturday. We will post more on Sunday. Thanks! I am already watching this thread so can't wait for more good news
|
|
|
Ok guys I have asked this question before but got no response so I decided to show you what I mean: Any explanation from the Antminer gurus why my NOT OVERCLOCKED Antminer hits these speeds? I am not saying I am not happy but, Is this going to cause a problem to my miner? Please let me know. Thank you
|
|
|
Sooooooo....
Where the fuck do we buy these...
I was wondering the same thing, but wasn't going to ask now as I believe it is better to wait till 10-15 Feb when their prices drop. I am not willing to invest $2K for something that makes around $24 a day when I can only invest $1200 to get another Antminer that makes $40 a day.
|
|
|
|