Please make sure you have swapped your XUV to TOK. Today only a few hours remaining for the deadline.
A Huge exchange coming up from top 15 exchanges
When is it going to be approximately? |
|
|
|
|
Hi! What is the time for TOK to become mature? My MN is being active now for 36 hours already but does not stake (not staking because you don't have mature coins)!
|
|
|
|
|
Exchange ends 25th of december at 00:00, what time zone? I can not get access to my wallet for following 13 hours.
|
|
|
|
|
Hi! Wallet has 0 active connections. It is because the dev changed and the network is offline or promblems are on me side?
|
|
|
|
where to get the OutputIndex info to setup mn?
Have you used these instructions? |
|
|
|
Hi everyone! Could you please advise what should i do in my situation. The matter is that i bought XUV via BTC transaction 25 hours ago, transaction is still unconfirmed so no XUV is on my wallet. Same problem was been faced by me and also i used several transaction accelerators, but none was of any use. Untill now my transaction is stuck from nearly 6 days and yet I can't do anything else rather than waiting for the transaction to be confirmed. Sad. Does the dev know about such a problem? What else can we do except for waiting? UPD: just recieved my coins  Glad you got ur coins after all, sometimes we need a little patience and everything will go well, anyway I hope you set up your masternode successfully, and will get some profit as they promised. Give me your ID and i will help to push it! Have problems with setting up the masternode though. |
|
|
|
Need some help again guys. Trying to start a masternode. Do as it is written here up to step 10. Console says "Masternode started successfully" but i can not see any masternodes in Masternodes/My masternodes tab. It is empty. What is done wrong? Help me to fix this please. Also in the down-right corner it pops out "Not staking because you do not have mature coins". How long should i wait for them to become mature? Masternode does not work still. Masternodes/My masternodes tab is empty. |
|
|
|
Need some help again guys. Trying to start a masternode. Do as it is written here up to step 10. Console says "Masternode started successfully" but i can not see any masternodes in Masternodes/My masternodes tab. It is empty. What is done wrong? Help me to fix this please. |
|
|
|
Hi everyone! Could you please advise what should i do in my situation. The matter is that i bought XUV via BTC transaction 25 hours ago, transaction is still unconfirmed so no XUV is on my wallet. Same problem was been faced by me and also i used several transaction accelerators, but none was of any use. Untill now my transaction is stuck from nearly 6 days and yet I can't do anything else rather than waiting for the transaction to be confirmed. Sad. Does the dev know about such a problem? What else can we do except for waiting? UPD: just recieved my coins |
|
|
|
Hi everyone! Could you please advise what should i do in my situation. The matter is that i bought XUV via BTC transaction 25 hours ago, transaction is still unconfirmed so no XUV is on my wallet. Hi. I pushed here https://pool.viabtc.com/tools/txaccelerator/ your transaction, will wait can be confirmed "Acceleration succeeded" But I have no confidence  Thank you! I'va just pushed it also. Is it normal for transaction to hang so long? |
|
|
|
Hi everyone! Could you please advise what should i do in my situation. The matter is that i bought XUV via BTC transaction 25 hours ago, transaction is still unconfirmed so no XUV is on my wallet. |
|
|
|
Всем привет! Ребята, знатоки, подскажите как питать это чудо https://www.asus.com/ru/Motherboards/B250-MINING-EXPERT/. Интересуют варианты как с серверными блоками так и с обычными. Только обычные менее киловатта, а то цена кусючая. Там в описании указано, что плата разделена на 3 зоны по питанию. Хотел купить серверный HP на 2250 Ватт HSTNS-PR09 и питать им 10 карт + саму систему, получится ли так сделать, чтобы все работало или нужно четко разделять блоки питания по питаемым зонам? Там еще и молексы на плате распаяны, наверное, как дополнительные входы для подачи напряжения, их тоже задействовать нужно в таком случае, верно? Или проще накупить АТХ обычных и синхронизаторами скрепить, но это выйдет сильно дороже? Заранее благодарю, если Вы вникнете в ситуацию и поможете разобраться. |
|
|
|
Привет, уважаемый гуру Вот ломаю голову над вопросом одним, надеюсь, что ты мне поможешь осознать. Как-то у меня был кошелек, на который перевели некую сумму. Номер этого кошелька я не знаю сейчас, однако, узнать его возможно. Это был номер кошелька официального клиента. Есть ли способ восстановить к нему доступ и получить свою крипту? Заранее спасибо! UPD: Нашел этот адрес, посмотрел блокчейн, а на нем пусто. Вспомнил, что это был кошелек mybitcoin, тех самых, которые кинули пользователей в 2011м и украли все накопления в размене почти 80000 битков. |
|
|
|
|
Решено когда начнется сбор средств?
|
|
|
|
Почитал, воодушевился и сделал так:  Жду вместе со всеми  |
|
|
|
I said who cares like forget about it. Something is wrong with your windows but it doesn't matter, you still got it to work.
My windows is W8x64. It is a month old, not tweaked or smth likr that. Just launched cgminer with .exe than put in url, name and pass it launched but could not create .bin files and crashed. I repeated the procedure with my old .bin files from 2.11.4. It works. Hashrate is bad but it works. Also tried to launch BFGminer with .exe than put in url, name and pass. It launched but gives me: ocl 0: invalid nonce - HW error. Catalyst 13.6 beta |
|
|
|
Yes, it opens with notepad! Contents of config file: cgminer -o http://pool.itzod.ru:3333 -u *** -p *** -I d --gpu-engine 900,850 --gpu-memclock 300,300 --temp-target 85 -k diablo |
|
|
|
Your permissions are screwed, try a check disk.
If not who cares, you have a good work around. Next.
Check disk reports that no mistakes found! The 2nd part of your message is not clear to me. Please explain. How do I fix those permissions? |
|
|
|
|
Show Posts
