Show Posts
|
Pages: [1] 2 3 »
|
Care-i situatia cu https://trade.bitcoinromania.ro/ ? Nu le-am folosit nici o data. De fapt singurul exchange romanesc pe care l-am folosit a fst Coinflux inainte sa dea faliment
|
|
|
Does anyone has EVGA XC3 Black? As i see on evga forum, there is no backplate for this card.
Thanks in advance!
that's correct, that model doesn't have a backplate
|
|
|
Ok, it seems that T-Rex miner is also dead with the new nVidia drivers, but I tested lolminer and for now at least it seems that it works.
So until Phoenix miner gets updated, you either downgrade your drivers or switch to lolminer
|
|
|
I can also confirm that after updating to latest nVidia drivers 460.79 my 3080 stopped working with Phoenix Miner 5.3B
|
|
|
I've got an update regarding the Gigabyte Vision OC:
I managed to get a decent hashrate with it:
~96 Mh/s @ 224W PL 61 core +90 mem +1000 Fan 75
core actually fluctuates between 1200 -1400Mhz GPU temp (according to MSI afterburner) 51c in a closed case and @ 21c ambient temp
|
|
|
Yes, I know about the thermal pad solution but that would void the warranty
|
|
|
OK, so I returned my Gigabyte Eagle OC because it had a reduced hashrate. Since I couldn't get any other card I was forced getting a Gigabyte Vision OC 3080 (it's for my gaming rig)
It seems that unfortunately this one also has the same problem as the Eagle and Gaming variant. As a matter of fact I think it's the exact same card as the Gaming OC except the design of the cooler.
So don't buy any Gigabyte cards if you plan on using them for mining.
In a week or so I expect to receive EVGA XC3 Ultra cards. Hope I will have better luck with them!
|
|
|
thanks...my russian is a little but rusty ![Grin](https://bitcointalk.org/Smileys/default/grin.gif)
|
|
|
I have the same issue as you, with an RTX 3080 Gigabyte Eagle OC. Starts out at 88Mh, slowly dropping to 77Mh. I installed the GPU straight on the motherboard since this is also my gaming rig. I noticed that the reason for this is that the core clock is dropping automatically to around 1000Mhz for some reason. Also, total power consumption according to Phoenix miner is around 200W. (same thing with Claymore btw)
Did you find a solution for this problem? Thanks
|
|
|
My Gigabyte 3080 drops hashing after mining for a minute or two.
Tried changing risers and power connectors to no avail.
I have Silverstone Platinum PSU 1200 W.
The hashrate drops on both everything stock and TDP at 80 or 70 or any other value as well.
I have the same issue as you, with an RTX 3080 Gigabyte Eagle OC. Starts out at 88Mh, slowly dropping to 77Mh. I installed the GPU straight on the motherboard. I noticed that the reason for this is that the core clock is dropping automatically to around 1000Mhz for some reason. Also, total power consumption according to Phoenix miner is around 200W. (same thing with Claymore btw) Did you find a solution for this problem? Thanks
|
|
|
I used to use afterburner to undervolt on blockchain driver. Recently I updated to 18.2 drivers and now use overdriventool. The only problem is that I can't undervolt the Asus rog strix rx570s. Overdrive accepts the voltage and applies it. But HWinfo shows a higher voltage. No matter what I set the voltage to in overdrive or claymore command line, HWinfo always shows the same voltage for the rog rx570s.
Voltage control is fine on msi rx570 and on all 580s.
Any ideas? Any other software that can apply a voltage offset like afterburner does?
sometimes OC doesnt work when you don't have a monitor (or fake monitor plug) plugged into one of the cards.
|
|
|
thanks, that's what I tought. And yes, all are standard PCI-e USB powered risers. v007 and v008s
|
|
|
hi all!
I ordered some v008s risers, and one of the risers has a manufacturing problem with the small piece that connects to the motherboard (not all pins are separated). Can I safely mix the bigger piece of the v008s riser (the piece u plug your GPU into) with the small piece of a older model, like the v007? Are they compatible?
|
|
|
hey guys! I'm willing to give simplemining a try. I have a 6GPU nVidia rig that is running stable for months now under Win10. If I just take all OC information from MSI Afterburner, will these settings work for simplemining too?
And one more question: is there a one time only fee for simplemining? (as I can see the $2/month is currently the only payment option?)
|
|
|
Eu minez cu claymore, cu 800-850Mh/ GPU (Rx580 8gb) si folosesc nanopool. Payout direct pe exchange cryptopia
|
|
|
Se poate folosi si Wallet de Exchange sau trebuie pus cel de pe Blockchain? A incercat cineva? In felul asta s-ar evita fee-ul de transfer intre Wallet-ul din Blockchain si cel de Exchange. (Bittrex, Poloniex ...)
Ce fee-uri? Daca vb de ETH, astea sunt minime, aprox $0.2
|
|
|
Ca si pas urmator ar trebui sa-ti transfer banii pe un exchange care are listata monezile cautate de tine. In schimb daca ai cumparat BTC si le ai in walletul tau,lasa-l acolo pt ca asa cum ai zis tu taxa de transfer ar fi destul de mare. Oricum,pe termen lung nici BTC nu e o investitie rea... :-) Data urmatoare mai bine cumperi ETH sau LTC de la coinflux pe care poti sa le transferi la costuri minime intre walleturi. Atentie la volatilitate! In ultinele zile atat ETH cat si LTC au luato razna... :-)
|
|
|
|