Show Posts
|
Pages: [1]
|
Does anyone face a problem where the miner just stops? i mean the cards are running and everything is running but the miner just freezes
Are you using Windows, and have you clicked on the command window? cmd.exe stops scrolling new text when you select even one character. If you push enter, it will scroll again.
|
|
|
I can't for the life of me get Siacoin to dual mine. Anything obvious I'm doing wrong? Ethereum runs fine, but SC never gets authorized, and my SC hash rate just sits at 0.000 MH/s and I just keep getting SC job timeouts. My startup script: ethdcrminer64.exe -epool eth-us-east1.nanopool.org:9999 -ewal ***my ethereum info*** -epsw x -dpool stratum+tcp://sia-us-west1.nanopool.org:7777 -dwal ***my siacoin address***/***miner name***/***email address*** -ftime 10 -dcoin sia
Specify -allpools 1 -allcoins 1 in startup script Thanks, but no luck there either. Same issue as before. I think it's really weird that I get the "SC - Stratum: connected" line but never get a "SC Authorized" line. Would there be any weird firewall stuff that could be causing this that would let through ETH but not SC? Did you comment out the config file dpools.txt and\or epools.txt? the miner will go check those file first then the parameter in the .bat file.
Everything in config.txt appears to be commented out already, and dpools and epools contain consistent info with what I'm putting into my startup script.
|
|
|
I can't for the life of me get Siacoin to dual mine. Anything obvious I'm doing wrong? Ethereum runs fine, but SC never gets authorized, and my SC hash rate just sits at 0.000 MH/s and I just keep getting SC job timeouts. My startup script: ethdcrminer64.exe -epool eth-us-east1.nanopool.org:9999 -ewal ***my ethereum info*** -epsw x -dpool stratum+tcp://sia-us-west1.nanopool.org:7777 -dwal ***my siacoin address***/***miner name***/***email address*** -ftime 10 -dcoin sia
[....] Any thoughts? Drop the stratum+tcp part of the server name. From my own .bat file: -dpool sia-eu1.nanopool.org:7777
Thanks--just tried that too, but got the same outcome.
|
|
|
I can't for the life of me get Siacoin to dual mine. Anything obvious I'm doing wrong? Ethereum runs fine, but SC never gets authorized, and my SC hash rate just sits at 0.000 MH/s and I just keep getting SC job timeouts. My startup script: ethdcrminer64.exe -epool eth-us-east1.nanopool.org:9999 -ewal ***my ethereum info*** -epsw x -dpool stratum+tcp://sia-us-west1.nanopool.org:7777 -dwal ***my siacoin address***/***miner name***/***email address*** -ftime 10 -dcoin sia
My output (edited slightly for compactness): ����������������������������������������������������������������ͻ � Claymore's Dual ETH + DCR/SC/LBC/PASC GPU Miner v9.7 � ����������������������������������������������������������������ͼ
ETH: 5 pools are specified Main Ethereum pool is eth-us-east1.nanopool.org:9999 SC: 5 pools are specified Main Siacoin pool is sia-us-west1.nanopool.org:7777 AMD OpenCL platform not found CUDA initializing... NVIDIA Cards available: 5 CUDA Driver Version/Runtime Version: 9.0/8.0 GPU #0: GeForce GTX 1070, 8192 MB available, 15 compute units, capability: 6.1 GPU #1: GeForce GTX 1070, 8192 MB available, 15 compute units, capability: 6.1 GPU #2: GeForce GTX 1070, 8192 MB available, 15 compute units, capability: 6.1 GPU #3: GeForce GTX 1070, 8192 MB available, 15 compute units, capability: 6.1 GPU #4: GeForce GTX 1070, 8192 MB available, 15 compute units, capability: 6.1 Total cards: 5 ETH: Stratum - connecting to 'eth-us-east1.nanopool.org' <158.69.85.38> port 9999 DUAL MINING MODE ENABLED: ETHEREUM+SIACOIN ETH: eth-proxy stratum mode ETH: Stratum - Connected (eth-us-east1.nanopool.org:9999) Watchdog enabled SC: Stratum - connecting to 'sia-us-west1.nanopool.org' <45.32.71.82> port 7777 Remote management (READ-ONLY MODE) is enabled on port 3333
SC: Stratum - Connected (sia-us-west1.nanopool.org:7777) ETH: Authorized Setting DAG epoch #133... Setting DAG epoch #133 for GPU0 [snip] Create GPU buffer for GPU0 [snip] GPU0 DAG creation time - 5327 ms Setting DAG epoch #133 for GPU0 done [snip] ETH: 07/09/17-20:52:04 - SHARE FOUND - (GPU 0) ETH: Share accepted (140 ms)! Socket was closed remotely (by pool) SC: Job timeout, disconnect, retry in 20 sec...
ETH - Total Speed: 155.754 Mh/s, Total Shares: 1(1+0+0+0+0), Rejected: 0, Time: 00:00 ETH: GPU0 32.165 Mh/s, GPU1 27.200 Mh/s, GPU2 31.693 Mh/s, GPU3 32.887 Mh/s, GPU4 31.810 Mh/s SC - Total Speed: 0.000 Mh/s, Total Shares: 0(0+0+0+0+0), Rejected: 0 SC: GPU0 0.000 Mh/s, GPU1 0.000 Mh/s, GPU2 0.000 Mh/s, GPU3 0.000 Mh/s, GPU4 0.000 Mh/s Notice in there that it says ETH: Authorized, but it never says anything about SC: Authorized? I think this is my problem, but I don't know what else to do about it. What I've tried so far, none of which have been successful: - Generating a new Siacoin wallet address
- Changing my email address to a Gmail address
- -dcri intensities from about 1 to 500
- switching from Nanopool to Miningpoolhub
- switching to different Nanopool servers
- Claymore 9.5 and 9.7
Any thoughts?
|
|
|
I am so desperate that I will donate eth if i solve this....
6x 1070, asrock h81 btc, win 10, latest nvidia drivers, claymore 9.6, 1200w PSU, Virtual set to 16 gb. Even at stock settings , the miner crashes, sometimes directly , and sometimes after 1-2 hours. I have tried different nvidia drivers, and even tried previous claymore versions. Tried swapping the cards around and setting in bios gen1/gen2 ( it should work out of the box ) I have connected the 2 molex connectors on the mobo and also having 6 powered usb risers. Only time i can get it to go a bit longer is if i have it at stock, but change the Power target to around 60% for all cards. I have a "wattman" and it says computer is taking 650w from the wall. but thats with low Power target, otherwise it is around 900. When it crashes, 1 card Always dissapears , both from the miner and from Afterburner ( in AB its there but cant change anything because its grayed out ) resulting in having to reset PC. Sometimes when it crashes , my monitor that is connected to 1 of the cards also shuts down. Most of the times i get BSOD after the crash and if that doesnt happen, the whole computer freezes up. I really want to Think there is enough Power to drive this with 1200w.
Edit : Just Before it crashes, my mouse curser is almost unmovable. Really laggy. But both cpu and memory are far from maxed out. My cards temp are also not capping, just around 60.
Any ideas ?
Sounds like you're either overclocking too much, or one of your risers has an intermittent connection. Shady risers do all kinds of weird stuff.
|
|
|
|