Hello, I found the issue

The ground wire was not connected to the ground in the fuse box but connected in the miner 3phase connection to the 5pin cable.
The ground wire was near the 3phase cables in the fuse box and was collecting "parasite electricity" and the PSU was collecting electricity thru the ground connection.
I unplug the ground wire from the adaptor for the miners cable and now is working fine.
(there is only 3phase + N there)

Thank you all,

Hello again,

The T21 PDU has 6 sockets 3 groups of 2 pairs ex:
1-> L1 L2 L3
2 -> L1 L2 L3
3-> L2 L3 L1
4-> L2 L3 L1
5-> L3 L1 L2
6-> L3 L1 L2

 So the order of the phases doesn't matter, 2 T21 are working perfect on 2 different sockets.
They are grouped like this because you can buy an adapter from 5 pins to 3 pins so you can connect a S21 and in this way you will always pull a live wire from a different phase.

BUT,
At the other location i have L1 L2 L3 N PE and still doesn't work any miner ) (all phases are in correct order "to the right")
each phase has over 220V
N is ok
On the stock firmware i still have :
Warning code J1:2
"Check whether chain1 connection is normal, update the firmware to the latest version, replace the hashboard, or return to factory for repair"

And on the other T21 i have Braiins and has PSU issues there.

I don t have any explanation for this

Thank you

Hello,
 I took the miners to my solar mining "farm" where i have 3phase correctly installed and the miners work PERFECT !
 The issue is that at the other location where the miners where "faulty" the 3phase grid is not in the normal "rotation order to the right" ( L1 L2 L3 400V).
I am waiting for a measuring tool (20$) that shows the correct order for the 3phase grid.

I hope that will solve all the problems

Thank you all 

I think that you are right, the issue is at the 3phase system
I will test the T21s at my place where i also have 3phase with solar power and check there.

Today i tried with a 3rd T21 on that 3phase system and have the same errors.

I did order a "ANTPDU PW12V1 for Antminer T21 " from zeus bts .com  (1week i will have it)
after i will try it i will leave a comment here.

Hello,
I have 3 new T21 (all have braiins os now)

I tried the following tests:
1) new PSU on the old T21 -> same error
2) took new Control Board on the old T21 with the new PSU -> braiins won't start mining because find damaged HahBoard -> also said that i cannot disable on hashboard due to the Control Board that cannot support this;
     a) still tried to unplug the data cable from each board to find which is faulty ( same error-> cannot mine because cannot start mining if one board is missing)
3) took the old Control Board (stock firmware) and put on the new T21 miner (new hashboards) with the old PSU -> same error -> cannot mine
4) new control board (braiins) + new hashboards + old psu  + reset to factory settings => miner freezes in his OS with error that cannot load the proper configurations for this miner 

Conclusion 1:
now i have 2 T21 broken )

Conclusion 2:
I did saw on the logs that the miner is checking also the SN from the Boards and the PSU => i think that they are paired together

Step 1:
The only thing to do now is to put them back as they where bough and try to reinstall brains on the new T21
Step 2:
The old T21 will be a real challenge to fix it and solve the mystery ( on this miner the braiins OS cannot be installed) (it has the last firmware from bitmain)

 I will buy another T21 and replace the PSU, after that i will be sure if this will solve the issue (and buy the PSU or the Controller).

 Thank you all for your time and ideas 

I checked the power bard that feed the hashboards and they were 0V

I think that the controller is stopping the power supply to deliver 14v to the hashboards

Here is the Log History:

2024-12-19 10:20:00 Mask num 0x1fffe000
2024-12-19 10:20:00 Note: addrInterval or corenum is not initialized.
2024-12-19 10:20:10 Chain[0]: find 0 asic, times 0
2024-12-19 10:20:15 Chain[0]: find 0 asic, times 1
2024-12-19 10:20:20 Chain[0]: find 0 asic, times 2
2024-12-19 10:20:20 Chain 0 only find 0 asic, will power off hash board 0
2024-12-19 10:20:20 Sweep error string = J1:2.
2024-12-19 10:20:20 ERROR_ASIC_NUM: asic number is not right
2024-12-19 10:20:20 stop_mining: asic number is not right
2024-12-19 10:20:20 uninit_temp_info
2024-12-19 10:20:20 do not read temp anymore...
2024-12-19 10:20:20 uninit_asic_temp_vol_info
2024-12-19 10:20:20 do not read asic_temp_vol anymore...
2024-12-19 10:20:20 cancel thread thread_id_rd_nonce_reg
2024-12-19 10:20:20 ****power off hashboard****
2024-12-19 10:20:20 power off
2024-12-19 10:20:20 asic_temperature_and_voltage_monitor_thread exit
2024-12-19 10:20:20 temp monitor thread exit
2024-12-19 10:20:21 ERROR_SOC_INIT: soc init failed!
2024-12-19 10:20:21 reach max restart times
2015-01-01 00:00:15 Open miner sn file /config/mac error
2015-01-01 00:00:15 Miner compile time: Tue Jul 16 14:39:58 CST 2024 type: Antminer T21 sn :HQDZF2UBDJBBA05ZR mac:
2015-01-01 00:00:17 This is fix-freq version
2015-01-01 00:00:17 Miner compile time: Tue Jul 16 14:39:58 CST 2024 type: Antminer T21
2015-01-01 00:00:17 Miner sn: HQDZF2UBDJBBA05ZR
2015-01-01 00:00:17 commit version: 02407a8d 2024-04-08 13:24:38, build by: jenkins 2024-07-16 14:59:27
2015-01-01 00:00:17 opt_multi_version     = 1
2015-01-01 00:00:17 opt_bitmain_ab        = 1
2015-01-01 00:00:17 mid_auto_gen          = 1
2015-01-01 00:00:17 opt_bitmain_work_mode = 0
2015-01-01 00:00:17 port 439 already exported
2015-01-01 00:00:17 port 454 already exported
2015-01-01 00:00:17 port 440 already exported
2015-01-01 00:00:17 port 455 already exported
2015-01-01 00:00:17 port 441 already exported
2015-01-01 00:00:17 port 456 already exported
2015-01-01 00:00:17 port 438 already exported
2015-01-01 00:00:17 port 453 already exported
2015-01-01 00:00:17 port 446 already exported
2015-01-01 00:00:17 port 445 already exported
2015-01-01 00:00:17 Note: front fan is power on!
2015-01-01 00:00:17 Note: rear fan is power on!
2015-01-01 00:00:17 start the http server
2015-01-01 00:00:17 httpserver:6060 started ok
2015-01-01 00:00:17 get test_loop_securely_find_asic_num failed
2015-01-01 00:00:17 abandon mix board!
2015-01-01 00:00:17 get mix boardname[0][BHB68701], name:BHB68701
2015-01-01 00:00:17 bad chain id = 3
2015-01-01 00:00:20 bad chain id = 3
2015-01-01 00:00:22 power on
2024-12-19 15:42:19 power off
2024-12-19 15:42:20 ==========================capability start==========================
2024-12-19 15:42:20 board num = 3
2024-12-19 15:42:20 board id = 0, chain num = 1
2024-12-19 15:42:20    chain id = 0
2024-12-19 15:42:20 board id = 1, chain num = 1
2024-12-19 15:42:20    chain id = 1
2024-12-19 15:42:20 board id = 2, chain num = 1
2024-12-19 15:42:20    chain id = 2
2024-12-19 15:42:20 ==========================capability end============================
2024-12-19 15:42:20 chain num = 3
2024-12-19 15:42:20 i2c chain = 0, master = 0x0, slave = 0xa0
2024-12-19 15:42:20 i2c chain = 1, master = 0x0, slave = 0xa2
2024-12-19 15:42:20 i2c chain = 2, master = 0x0, slave = 0xa4
2024-12-19 15:42:24 load chain 0 eeprom data
2024-12-19 15:42:27 load chain 1 eeprom data
2024-12-19 15:42:30 load chain 2 eeprom data
2024-12-19 15:42:30 eeprom load ret:0
2024-12-19 15:42:30 miner:BHB68701,board_name:BHB68701
2024-12-19 15:42:30 create thread get_nonce_and_register_thread
2024-12-19 15:42:30 fixed working voltage = 1360
2024-12-19 15:42:30 Chain

• PCB Version: 0x0100

2024-12-19 15:42:30 Chain

• BOM Version: 0x0000

2024-12-19 15:42:30 Chain [1] PCB Version: 0x0100
2024-12-19 15:42:30 Chain [1] BOM Version: 0x0000
2024-12-19 15:42:30 Chain [2] PCB Version: 0x0100
2024-12-19 15:42:30 Chain [2] BOM Version: 0x0000
2024-12-19 15:42:30 bad chain id = 3
2024-12-19 15:42:33 Fan check passed.
2024-12-19 15:42:33 init fan pid target=65
2024-12-19 15:42:33 max sensor num = 4
2024-12-19 15:42:33 temperature_monitor_thread start...
2024-12-19 15:42:33 STATUS_INITED: soc init done!
2024-12-19 15:42:33 i2c chain = 0, master = 0x0, slave = 0x90
2024-12-19 15:42:33 asic_temperature_and_voltage_monitor_thread start...
2024-12-19 15:42:33 i2c chain = 0, master = 0x0, slave = 0x98
2024-12-19 15:42:33 i2c chain = 1, master = 0x0, slave = 0x92
2024-12-19 15:42:33 i2c chain = 1, master = 0x0, slave = 0x9a
2024-12-19 15:42:33 i2c chain = 2, master = 0x0, slave = 0x94
2024-12-19 15:42:33 i2c chain = 2, master = 0x0, slave = 0x9c
2024-12-19 15:42:36 start to init...
2024-12-19 15:42:36 i2c_sim_init start
2024-12-19 15:42:36 init gpio477
2024-12-19 15:42:36 init gpio476
2024-12-19 15:42:36 i2c_sim_init end
2024-12-19 15:42:41 get power version failed
2024-12-19 15:42:41 check power version failed, use v2 protocal to try it again
2024-12-19 15:42:43 power open power_version = 0x6a
2024-12-19 15:42:46 power calibration data:
2024-12-19 15:42:46  9  B 92 41 
2024-12-19 15:42:46 A5 71 FC 47 
2024-12-19 15:42:46 29 26 EC DB 
2024-12-19 15:42:46 FF D3  0 FF 
2024-12-19 15:42:46  0 FE FF  0 
2024-12-19 15:42:46  0 FE  0 80 
2024-12-19 15:42:46 80 80 80 80 
2024-12-19 15:42:46 1F E0 3F 45 
2024-12-19 15:42:50 calibration data 1  15.520556    15.555556   
2024-12-19 15:42:50 calibration data 2  15.075111    15.111111   
2024-12-19 15:42:50 calibration data 3  14.628667    14.666667   
2024-12-19 15:42:50 calibration data 4  14.183222    14.222222   
2024-12-19 15:42:50 calibration data 5  13.737778    13.777778   
2024-12-19 15:42:50 calibration data 6  13.293333    13.333333   
2024-12-19 15:42:50 calibration data 7  12.848889    12.888889   
2024-12-19 15:42:50 calibration data 8  12.402444    12.444444   
2024-12-19 15:42:50 calibration data 9  11.957000    12.000000   
2024-12-19 15:42:50 power is Calibrated
2024-12-19 15:42:50 power sn:KLKT343BDJBBF2123
2024-12-19 15:42:50 enable_power_calibration,calibration date:211208.
2024-12-19 15:42:54 get power version failed
2024-12-19 15:42:54 check power version failed, use v2 protocal to try it again
2024-12-19 15:42:56 power type version: 0x006a
2024-12-19 15:42:56 power history status: -1
2024-12-19 15:42:58 disable power watchdog: 0x0000
2024-12-19 15:42:59 Initializing the power, please wait, this may take up to 2 minutes...
2024-12-19 15:43:29 Slept 30 seconds, diff = 0.
2024-12-19 15:43:39 set_voltage_by_steps to 1500.
2024-12-19 15:43:41 power on
2024-12-19 15:43:56 bad chain id = 3
2024-12-19 15:43:59 bitmain_get_sample_voltage:-1.000000 < 0
2024-12-19 15:43:59 ERROR_POWER_LOST: power voltage read failed, pls check!
2024-12-19 15:44:01 Get power code[0-3 4-7 8-11 12-13] 55aa0c0e 00000100 00050000 0d13, power_code:0x00000500
2024-12-19 15:44:01 reach max restart times
2024-12-19 15:44:02 Version num 65536
2024-12-19 15:44:02 Mask num 0x1fffe000
2024-12-19 15:44:02 Note: addrInterval or corenum is not initialized.
2024-12-19 15:44:03 start up min temp by 75a = 20
2024-12-19 15:44:12 Chain[0]: find 0 asic, times 0
2024-12-19 15:44:17 Chain[0]: find 0 asic, times 1
2024-12-19 15:44:22 Chain[0]: find 0 asic, times 2
2024-12-19 15:44:22 Chain 0 only find 0 asic, will power off hash board 0
2024-12-19 15:44:22 Sweep error string = J1:2.
2024-12-19 15:44:22 ERROR_ASIC_NUM: asic number is not right
2024-12-19 15:44:22 stop_mining: asic number is not right
2024-12-19 15:44:22 uninit_temp_info
2024-12-19 15:44:22 do not read temp anymore...
2024-12-19 15:44:22 uninit_asic_temp_vol_info
2024-12-19 15:44:22 do not read asic_temp_vol anymore...
2024-12-19 15:44:22 cancel thread thread_id_rd_nonce_reg
2024-12-19 15:44:22 ****power off hashboard****
2024-12-19 15:44:22 power off
2024-12-19 15:44:22 asic_temperature_and_voltage_monitor_thread exit
2024-12-19 15:44:23 temp monitor thread exit
2024-12-19 15:44:23 ERROR_SOC_INIT: soc init failed!
2024-12-19 15:44:23 reach max restart times
2015-01-01 00:00:15 Open miner sn file /config/mac error
2015-01-01 00:00:15 Miner compile time: Tue Jul 16 14:39:58 CST 2024 type: Antminer T21 sn :HQDZF2UBDJBBA05ZR mac:
2015-01-01 00:00:17 This is fix-freq version
2015-01-01 00:00:17 Miner compile time: Tue Jul 16 14:39:58 CST 2024 type: Antminer T21
2015-01-01 00:00:17 Miner sn: HQDZF2UBDJBBA05ZR
2015-01-01 00:00:17 commit version: 02407a8d 2024-04-08 13:24:38, build by: jenkins 2024-07-16 14:59:27
2015-01-01 00:00:17 opt_multi_version     = 1
2015-01-01 00:00:17 opt_bitmain_ab        = 1
2015-01-01 00:00:17 mid_auto_gen          = 1
2015-01-01 00:00:17 opt_bitmain_work_mode = 0
2015-01-01 00:00:17 port 439 already exported
2015-01-01 00:00:17 port 454 already exported
2015-01-01 00:00:17 port 440 already exported
2015-01-01 00:00:17 port 455 already exported
2015-01-01 00:00:17 port 441 already exported
2015-01-01 00:00:17 port 456 already exported
2015-01-01 00:00:17 port 438 already exported
2015-01-01 00:00:17 port 453 already exported
2015-01-01 00:00:17 port 446 already exported
2015-01-01 00:00:17 port 445 already exported
2015-01-01 00:00:17 Note: front fan is power on!
2015-01-01 00:00:17 Note: rear fan is power on!
2015-01-01 00:00:17 start the http server
2015-01-01 00:00:17 httpserver:6060 started ok
2015-01-01 00:00:17 get test_loop_securely_find_asic_num failed
2015-01-01 00:00:17 abandon mix board!
2015-01-01 00:00:17 get mix boardname[0][BHB68701], name:BHB68701
2015-01-01 00:00:17 bad chain id = 3
2015-01-01 00:00:20 bad chain id = 3
2015-01-01 00:00:22 power on
2024-12-19 18:12:25 power off
2024-12-19 18:12:26 ==========================capability start==========================
2024-12-19 18:12:26 board num = 3
2024-12-19 18:12:26 board id = 0, chain num = 1
2024-12-19 18:12:26    chain id = 0
2024-12-19 18:12:26 board id = 1, chain num = 1
2024-12-19 18:12:26    chain id = 1
2024-12-19 18:12:26 board id = 2, chain num = 1
2024-12-19 18:12:26    chain id = 2
2024-12-19 18:12:26 ==========================capability end============================
2024-12-19 18:12:26 chain num = 3
2024-12-19 18:12:26 i2c chain = 0, master = 0x0, slave = 0xa0
2024-12-19 18:12:26 i2c chain = 1, master = 0x0, slave = 0xa2
2024-12-19 18:12:26 i2c chain = 2, master = 0x0, slave = 0xa4
2024-12-19 18:12:29 load chain 0 eeprom data
2024-12-19 18:12:33 load chain 1 eeprom data
2024-12-19 18:12:36 load chain 2 eeprom data
2024-12-19 18:12:36 eeprom load ret:0
2024-12-19 18:12:36 miner:BHB68701,board_name:BHB68701
2024-12-19 18:12:36 create thread get_nonce_and_register_thread
2024-12-19 18:12:36 fixed working voltage = 1360
2024-12-19 18:12:36 Chain

• PCB Version: 0x0100

2024-12-19 18:12:36 Chain

• BOM Version: 0x0000

2024-12-19 18:12:36 Chain [1] PCB Version: 0x0100
2024-12-19 18:12:36 Chain [1] BOM Version: 0x0000
2024-12-19 18:12:36 Chain [2] PCB Version: 0x0100
2024-12-19 18:12:36 Chain [2] BOM Version: 0x0000
2024-12-19 18:12:36 bad chain id = 3
2024-12-19 18:12:39 Fan check passed.
2024-12-19 18:12:39 init fan pid target=65
2024-12-19 18:12:39 max sensor num = 4
2024-12-19 18:12:39 STATUS_INITED: soc init done!
2024-12-19 18:12:39 asic_temperature_and_voltage_monitor_thread start...
2024-12-19 18:12:39 temperature_monitor_thread start...
2024-12-19 18:12:39 i2c chain = 0, master = 0x0, slave = 0x90
2024-12-19 18:12:39 i2c chain = 0, master = 0x0, slave = 0x98
2024-12-19 18:12:39 i2c chain = 1, master = 0x0, slave = 0x92
2024-12-19 18:12:39 i2c chain = 1, master = 0x0, slave = 0x9a
2024-12-19 18:12:39 i2c chain = 2, master = 0x0, slave = 0x94
2024-12-19 18:12:39 i2c chain = 2, master = 0x0, slave = 0x9c
2024-12-19 18:12:42 start to init...
2024-12-19 18:12:42 i2c_sim_init start
2024-12-19 18:12:42 init gpio477
2024-12-19 18:12:42 init gpio476
2024-12-19 18:12:42 i2c_sim_init end
2024-12-19 18:12:47 get power version failed
2024-12-19 18:12:47 check power version failed, use v2 protocal to try it again
2024-12-19 18:12:48 power open power_version = 0x6a
2024-12-19 18:12:52 power calibration data:
2024-12-19 18:12:52  9  B 92 41 
2024-12-19 18:12:52 A5 71 FC 47 
2024-12-19 18:12:52 29 26 EC DB 
2024-12-19 18:12:52 FF D3  0 FF 
2024-12-19 18:12:52  0 FE FF  0 
2024-12-19 18:12:52  0 FE  0 80 
2024-12-19 18:12:52 80 80 80 80 
2024-12-19 18:12:52 1F E0 3F 45 
2024-12-19 18:12:55 calibration data 1  15.520556    15.555556   
2024-12-19 18:12:55 calibration data 2  15.075111    15.111111   
2024-12-19 18:12:55 calibration data 3  14.628667    14.666667   
2024-12-19 18:12:55 calibration data 4  14.183222    14.222222   
2024-12-19 18:12:55 calibration data 5  13.737778    13.777778   
2024-12-19 18:12:55 calibration data 6  13.293333    13.333333   
2024-12-19 18:12:55 calibration data 7  12.848889    12.888889   
2024-12-19 18:12:55 calibration data 8  12.402444    12.444444   
2024-12-19 18:12:55 calibration data 9  11.957000    12.000000   
2024-12-19 18:12:55 power is Calibrated
2024-12-19 18:12:55 power sn:KLKT343BDJBBF2123
2024-12-19 18:12:55 enable_power_calibration,calibration date:211208.
2024-12-19 18:13:00 get power version failed
2024-12-19 18:13:00 check power version failed, use v2 protocal to try it again
2024-12-19 18:13:02 power type version: 0x006a
2024-12-19 18:13:02 power history status: -1
2024-12-19 18:13:03 disable power watchdog: 0x0000
2024-12-19 18:13:04 Initializing the power, please wait, this may take up to 2 minutes...
2024-12-19 18:13:34 Slept 30 seconds, diff = 1.
2024-12-19 18:13:44 set_voltage_by_steps to 1500.
2024-12-19 18:13:47 power on
2024-12-19 18:14:02 bad chain id = 3
2024-12-19 18:14:05 bitmain_get_sample_voltage:-1.000000 < 0
2024-12-19 18:14:05 ERROR_POWER_LOST: power voltage read failed, pls check!
2024-12-19 18:14:07 Get power code[0-3 4-7 8-11 12-13] 55aa0c0e 00000100 00050000 0d13, power_code:0x00000500
2024-12-19 18:14:07 reach max restart times
2024-12-19 18:14:08 start up min temp by 75a = 22
2024-12-19 18:14:18 Chain[0]: find 0 asic, times 0
2024-12-19 18:14:23 Chain[0]: find 0 asic, times 1
2024-12-19 18:14:28 Chain[0]: find 0 asic, times 2
2024-12-19 18:14:28 Chain 0 only find 0 asic, will power off hash board 0
2024-12-19 18:14:28 Sweep error string = J1:2.
2024-12-19 18:14:28 ERROR_ASIC_NUM: asic number is not right
2024-12-19 18:14:28 stop_mining: asic number is not right
2024-12-19 18:14:28 uninit_temp_info
2024-12-19 18:14:28 do not read temp anymore...
2024-12-19 18:14:28 uninit_asic_temp_vol_info
2024-12-19 18:14:28 do not read asic_temp_vol anymore...
2024-12-19 18:14:28 cancel thread thread_id_rd_nonce_reg
2024-12-19 18:14:28 ****power off hashboard****
2024-12-19 18:14:28 power off
2024-12-19 18:14:28 asic_temperature_and_voltage_monitor_thread exit
2024-12-19 18:14:28 temp monitor thread exit
2024-12-19 18:14:29 ERROR_SOC_INIT: soc init failed!
2024-12-19 18:14:29 reach max restart times
2024-12-19 18:14:32 Version num 65536
2024-12-19 18:14:32 Mask num 0x1fffe000
2024-12-19 18:14:32 Note: addrInterval or corenum is not initialized.
2024-12-19 18:20:39 ****power off hashboard****
2024-12-19 18:20:39 power off
2024-12-19 18:20:55 Open miner sn file /config/mac error
2024-12-19 18:20:55 Miner compile time: Tue Jul 16 14:39:58 CST 2024 type: Antminer T21 sn :HQDZF2UBDJBBA05ZR mac:
2024-12-19 18:20:57 This is fix-freq version
2024-12-19 18:20:57 Miner compile time: Tue Jul 16 14:39:58 CST 2024 type: Antminer T21
2024-12-19 18:20:57 Miner sn: HQDZF2UBDJBBA05ZR
2024-12-19 18:20:57 commit version: 02407a8d 2024-04-08 13:24:38, build by: jenkins 2024-07-16 14:59:27
2024-12-19 18:20:57 opt_multi_version     = 1
2024-12-19 18:20:57 opt_bitmain_ab        = 1
2024-12-19 18:20:57 mid_auto_gen          = 1
2024-12-19 18:20:57 opt_bitmain_work_mode = 0
2024-12-19 18:20:57 port 439 already exported
2024-12-19 18:20:57 port 454 already exported
2024-12-19 18:20:57 port 440 already exported
2024-12-19 18:20:57 port 455 already exported
2024-12-19 18:20:57 port 441 already exported
2024-12-19 18:20:57 port 456 already exported
2024-12-19 18:20:57 port 438 already exported
2024-12-19 18:20:57 port 453 already exported
2024-12-19 18:20:57 port 446 already exported
2024-12-19 18:20:57 port 445 already exported
2024-12-19 18:20:57 Note: front fan is power on!
2024-12-19 18:20:57 Note: rear fan is power on!
2024-12-19 18:20:57 start the http server
2024-12-19 18:20:57 httpserver:6060 started ok
2024-12-19 18:20:57 get test_loop_securely_find_asic_num failed
2024-12-19 18:20:57 abandon mix board!
2024-12-19 18:20:57 get mix boardname[0][BHB68701], name:BHB68701
2024-12-19 18:20:57 bad chain id = 3
2024-12-19 18:21:00 bad chain id = 3
2024-12-19 18:21:02 power on
2024-12-19 18:21:16 power off
2024-12-19 18:21:17 ==========================capability start==========================
2024-12-19 18:21:17 board num = 3
2024-12-19 18:21:17 board id = 0, chain num = 1
2024-12-19 18:21:17    chain id = 0
2024-12-19 18:21:17 board id = 1, chain num = 1
2024-12-19 18:21:17    chain id = 1
2024-12-19 18:21:17 board id = 2, chain num = 1
2024-12-19 18:21:17    chain id = 2
2024-12-19 18:21:17 ==========================capability end============================
2024-12-19 18:21:17 chain num = 3
2024-12-19 18:21:17 i2c chain = 0, master = 0x0, slave = 0xa0
2024-12-19 18:21:17 i2c chain = 1, master = 0x0, slave = 0xa2
2024-12-19 18:21:17 i2c chain = 2, master = 0x0, slave = 0xa4
2024-12-19 18:21:20 load chain 0 eeprom data
2024-12-19 18:21:24 load chain 1 eeprom data
2024-12-19 18:21:27 load chain 2 eeprom data
2024-12-19 18:21:27 eeprom load ret:0
2024-12-19 18:21:27 miner:BHB68701,board_name:BHB68701
2024-12-19 18:21:27 create thread get_nonce_and_register_thread
2024-12-19 18:21:27 fixed working voltage = 1360
2024-12-19 18:21:27 Chain

• PCB Version: 0x0100

2024-12-19 18:21:27 Chain

• BOM Version: 0x0000

2024-12-19 18:21:27 Chain [1] PCB Version: 0x0100
2024-12-19 18:21:27 Chain [1] BOM Version: 0x0000
2024-12-19 18:21:27 Chain [2] PCB Version: 0x0100
2024-12-19 18:21:27 Chain [2] BOM Version: 0x0000
2024-12-19 18:21:27 bad chain id = 3
2024-12-19 18:21:30 Fan check passed.
2024-12-19 18:21:30 init fan pid target=65
2024-12-19 18:21:30 max sensor num = 4
2024-12-19 18:21:30 asic_temperature_and_voltage_monitor_thread start...
2024-12-19 18:21:30 STATUS_INITED: soc init done!
2024-12-19 18:21:30 temperature_monitor_thread start...
2024-12-19 18:21:30 i2c chain = 0, master = 0x0, slave = 0x90
2024-12-19 18:21:30 i2c chain = 0, master = 0x0, slave = 0x98
2024-12-19 18:21:30 i2c chain = 1, master = 0x0, slave = 0x92
2024-12-19 18:21:30 i2c chain = 1, master = 0x0, slave = 0x9a
2024-12-19 18:21:30 i2c chain = 2, master = 0x0, slave = 0x94
2024-12-19 18:21:30 i2c chain = 2, master = 0x0, slave = 0x9c
2024-12-19 18:23:02 cmd : set_miner_conf
2024-12-19 18:23:03 read ret 0 byte , ret =
2024-12-19 18:23:04 reload pool, need recalculate
2024-12-19 18:23:04 set_start_time_point total_tv_start_sys=139 total_tv_end_sys=140
2024-12-19 18:23:05 start to init...
2024-12-19 18:23:05 i2c_sim_init start
2024-12-19 18:23:05 init gpio477
2024-12-19 18:23:05 init gpio476
2024-12-19 18:23:05 i2c_sim_init end
2024-12-19 18:23:10 get power version failed
2024-12-19 18:23:10 check power version failed, use v2 protocal to try it again
2024-12-19 18:23:11 power open power_version = 0x6a
2024-12-19 18:23:15 power calibration data:
2024-12-19 18:23:15  9  B 92 41 
2024-12-19 18:23:15 A5 71 FC 47 
2024-12-19 18:23:15 29 26 EC DB 
2024-12-19 18:23:15 FF D3  0 FF 
2024-12-19 18:23:15  0 FE FF  0 
2024-12-19 18:23:15  0 FE  0 80 
2024-12-19 18:23:15 80 80 80 80 
2024-12-19 18:23:15 1F E0 3F 45 
2024-12-19 18:23:18 calibration data 1  15.520556    15.555556   
2024-12-19 18:23:18 calibration data 2  15.075111    15.111111   
2024-12-19 18:23:18 calibration data 3  14.628667    14.666667   
2024-12-19 18:23:18 calibration data 4  14.183222    14.222222   
2024-12-19 18:23:18 calibration data 5  13.737778    13.777778   
2024-12-19 18:23:18 calibration data 6  13.293333    13.333333   
2024-12-19 18:23:18 calibration data 7  12.848889    12.888889   
2024-12-19 18:23:18 calibration data 8  12.402444    12.444444   
2024-12-19 18:23:18 calibration data 9  11.957000    12.000000   
2024-12-19 18:23:18 power is Calibrated
2024-12-19 18:23:18 power sn:KLKT343BDJBBF2123
2024-12-19 18:23:18 enable_power_calibration,calibration date:211208.
2024-12-19 18:23:23 get power version failed
2024-12-19 18:23:23 check power version failed, use v2 protocal to try it again
2024-12-19 18:23:25 power type version: 0x006a
2024-12-19 18:23:25 power history status: -1
2024-12-19 18:23:26 disable power watchdog: 0x0000
2024-12-19 18:23:27 Initializing the power, please wait, this may take up to 2 minutes...
2024-12-19 18:23:57 Slept 30 seconds, diff = 1.
2024-12-19 18:24:07 set_voltage_by_steps to 1500.
2024-12-19 18:24:10 power on
2024-12-19 18:24:25 bad chain id = 3
2024-12-19 18:24:28 bitmain_get_sample_voltage:-1.000000 < 0
2024-12-19 18:24:28 ERROR_POWER_LOST: power voltage read failed, pls check!
2024-12-19 18:24:29 Get power code[0-3 4-7 8-11 12-13] 55aa0c0e 00000100 00050000 0d13, power_code:0x00000500
2024-12-19 18:24:29 fail to open counter file, err:No such file or directory
2024-12-19 18:24:30 Version num 65536
2024-12-19 18:24:30 Mask num 0x1fffe000
2024-12-19 18:24:30 Note: addrInterval or corenum is not initialized.
2024-12-19 18:24:59 stop_mining_and_restart: power voltage read failed, pls check!
2024-12-19 18:24:59 uninit_temp_info
2024-12-19 18:24:59 do not read temp anymore...
2024-12-19 18:24:59 uninit_asic_temp_vol_info
2024-12-19 18:24:59 do not read asic_temp_vol anymore...
2024-12-19 18:24:59 cancel thread thread_id_rd_nonce_reg
2024-12-19 18:24:59 ****power off hashboard****
2024-12-19 18:24:59 power off
2024-12-19 18:25:00 asic_temperature_and_voltage_monitor_thread exit
2024-12-19 18:25:00 temp monitor thread exit
2024-12-19 18:25:01 restart
2024-12-19 18:25:01 ****power off hashboard****
2024-12-19 18:25:01 power off
2024-12-19 18:25:32 httpserver6060 quit!
2024-12-19 18:25:47 Open miner sn file /config/mac error
2024-12-19 18:25:47 Miner compile time: Tue Jul 16 14:39:58 CST 2024 type: Antminer T21 sn :HQDZF2UBDJBBA05ZR mac:
2024-12-19 18:25:48 This is fix-freq version
2024-12-19 18:25:48 Miner compile time: Tue Jul 16 14:39:58 CST 2024 type: Antminer T21
2024-12-19 18:25:48 Miner sn: HQDZF2UBDJBBA05ZR
2024-12-19 18:25:48 commit version: 02407a8d 2024-04-08 13:24:38, build by: jenkins 2024-07-16 14:59:27
2024-12-19 18:25:48 opt_multi_version     = 1
2024-12-19 18:25:48 opt_bitmain_ab        = 1
2024-12-19 18:25:48 mid_auto_gen          = 1
2024-12-19 18:25:48 opt_bitmain_work_mode = 0
2024-12-19 18:25:48 port 439 already exported
2024-12-19 18:25:48 port 454 already exported
2024-12-19 18:25:48 port 440 already exported
2024-12-19 18:25:48 port 455 already exported
2024-12-19 18:25:48 port 441 already exported
2024-12-19 18:25:48 port 456 already exported
2024-12-19 18:25:48 port 438 already exported
2024-12-19 18:25:48 port 453 already exported
2024-12-19 18:25:48 port 446 already exported
2024-12-19 18:25:48 port 445 already exported
2024-12-19 18:25:48 Note: front fan is power on!
2024-12-19 18:25:48 Note: rear fan is power on!
2024-12-19 18:25:48 start the http server
2024-12-19 18:25:48 httpserver:6060 started ok
2024-12-19 18:25:48 get test_loop_securely_find_asic_num failed
2024-12-19 18:25:48 abandon mix board!
2024-12-19 18:25:48 get mix boardname[0][BHB68701], name:BHB68701
2024-12-19 18:25:48 bad chain id = 3
2024-12-19 18:25:51 bad chain id = 3
2024-12-19 18:25:53 power on
2024-12-19 18:26:06 power off
2024-12-19 18:26:07 ==========================capability start==========================
2024-12-19 18:26:07 board num = 3
2024-12-19 18:26:07 board id = 0, chain num = 1
2024-12-19 18:26:07    chain id = 0
2024-12-19 18:26:07 board id = 1, chain num = 1
2024-12-19 18:26:07    chain id = 1
2024-12-19 18:26:07 board id = 2, chain num = 1
2024-12-19 18:26:07    chain id = 2
2024-12-19 18:26:07 ==========================capability end============================
2024-12-19 18:26:07 chain num = 3
2024-12-19 18:26:07 i2c chain = 0, master = 0x0, slave = 0xa0
2024-12-19 18:26:07 i2c chain = 1, master = 0x0, slave = 0xa2
2024-12-19 18:26:07 i2c chain = 2, master = 0x0, slave = 0xa4
2024-12-19 18:26:10 load chain 0 eeprom data
2024-12-19 18:26:14 load chain 1 eeprom data
2024-12-19 18:26:17 load chain 2 eeprom data
2024-12-19 18:26:17 eeprom load ret:0
2024-12-19 18:26:17 miner:BHB68701,board_name:BHB68701
2024-12-19 18:26:17 create thread get_nonce_and_register_thread
2024-12-19 18:26:17 fixed working voltage = 1360
2024-12-19 18:26:17 Chain

• PCB Version: 0x0100

2024-12-19 18:26:17 Chain

• BOM Version: 0x0000

2024-12-19 18:26:17 Chain [1] PCB Version: 0x0100
2024-12-19 18:26:17 Chain [1] BOM Version: 0x0000
2024-12-19 18:26:17 Chain [2] PCB Version: 0x0100
2024-12-19 18:26:17 Chain [2] BOM Version: 0x0000
2024-12-19 18:26:17 bad chain id = 3
2024-12-19 18:26:20 Fan check passed.
2024-12-19 18:26:20 init fan pid target=65
2024-12-19 18:26:20 max sensor num = 4
2024-12-19 18:26:20 STATUS_INITED: soc init done!
2024-12-19 18:26:20 asic_temperature_and_voltage_monitor_thread start...
2024-12-19 18:26:20 temperature_monitor_thread start...
2024-12-19 18:26:20 i2c chain = 0, master = 0x0, slave = 0x90
2024-12-19 18:26:20 i2c chain = 0, master = 0x0, slave = 0x98
2024-12-19 18:26:20 i2c chain = 1, master = 0x0, slave = 0x92
2024-12-19 18:26:20 i2c chain = 1, master = 0x0, slave = 0x9a
2024-12-19 18:26:20 i2c chain = 2, master = 0x0, slave = 0x94
2024-12-19 18:26:20 i2c chain = 2, master = 0x0, slave = 0x9c
2024-12-19 18:26:23 start to init...
2024-12-19 18:26:23 i2c_sim_init start
2024-12-19 18:26:23 i2c_sim_init end
2024-12-19 18:26:28 get power version failed
2024-12-19 18:26:28 check power version failed, use v2 protocal to try it again
2024-12-19 18:26:29 power open power_version = 0x6a
2024-12-19 18:26:33 power calibration data:
2024-12-19 18:26:33  9  B 92 41 
2024-12-19 18:26:33 A5 71 FC 47 
2024-12-19 18:26:33 29 26 EC DB 
2024-12-19 18:26:33 FF D3  0 FF 
2024-12-19 18:26:33  0 FE FF  0 
2024-12-19 18:26:33  0 FE  0 80 
2024-12-19 18:26:33 80 80 80 80 
2024-12-19 18:26:33 1F E0 3F 45 
2024-12-19 18:26:36 calibration data 1  15.520556    15.555556   
2024-12-19 18:26:36 calibration data 2  15.075111    15.111111   
2024-12-19 18:26:36 calibration data 3  14.628667    14.666667   
2024-12-19 18:26:36 calibration data 4  14.183222    14.222222   
2024-12-19 18:26:36 calibration data 5  13.737778    13.777778   
2024-12-19 18:26:36 calibration data 6  13.293333    13.333333   
2024-12-19 18:26:36 calibration data 7  12.848889    12.888889   
2024-12-19 18:26:36 calibration data 8  12.402444    12.444444   
2024-12-19 18:26:36 calibration data 9  11.957000    12.000000   
2024-12-19 18:26:36 power is Calibrated
2024-12-19 18:26:36 power sn:KLKT343BDJBBF2123
2024-12-19 18:26:36 enable_power_calibration,calibration date:211208.
2024-12-19 18:26:41 get power version failed
2024-12-19 18:26:41 check power version failed, use v2 protocal to try it again
2024-12-19 18:26:43 power type version: 0x006a
2024-12-19 18:26:43 power history status: -1
2024-12-19 18:26:44 disable power watchdog: 0x0000
2024-12-19 18:26:45 Initializing the power, please wait, this may take up to 2 minutes...
2024-12-19 18:27:15 Slept 30 seconds, diff = 1.
2024-12-19 18:27:25 set_voltage_by_steps to 1500.
2024-12-19 18:27:28 power on
2024-12-19 18:27:43 bad chain id = 3
2024-12-19 18:27:46 bitmain_get_sample_voltage:-1.000000 < 0
2024-12-19 18:27:46 ERROR_POWER_LOST: power voltage read failed, pls check!
2024-12-19 18:27:47 Get power code[0-3 4-7 8-11 12-13] 55aa0c0e 00000100 00050000 0d13, power_code:0x00000500
2024-12-19 18:28:03 Version num 65536
2024-12-19 18:28:03 Mask num 0x1fffe000
2024-12-19 18:28:03 Note: addrInterval or corenum is not initialized.
2024-12-19 18:28:17 stop_mining_and_restart: power voltage read failed, pls check!
2024-12-19 18:28:17 uninit_temp_info
2024-12-19 18:28:17 do not read temp anymore...
2024-12-19 18:28:17 uninit_asic_temp_vol_info
2024-12-19 18:28:17 do not read asic_temp_vol anymore...
2024-12-19 18:28:17 cancel thread thread_id_rd_nonce_reg
2024-12-19 18:28:17 ****power off hashboard****
2024-12-19 18:28:17 power off
2024-12-19 18:28:18 temp monitor thread exit
2024-12-19 18:28:18 asic_temperature_and_voltage_monitor_thread exit
2024-12-19 18:28:18 restart
2024-12-19 18:28:18 ****power off hashboard****
2024-12-19 18:28:18 power off
2024-12-19 18:28:50 httpserver6060 quit!
2024-12-19 18:29:10 Open miner sn file /config/mac error
2024-12-19 18:29:10 Miner compile time: Tue Jul 16 14:39:58 CST 2024 type: Antminer T21 sn :HQDZF2UBDJBBA05ZR mac:
2024-12-19 18:29:12 This is fix-freq version
2024-12-19 18:29:12 Miner compile time: Tue Jul 16 14:39:58 CST 2024 type: Antminer T21
2024-12-19 18:29:12 Miner sn: HQDZF2UBDJBBA05ZR
2024-12-19 18:29:12 commit version: 02407a8d 2024-04-08 13:24:38, build by: jenkins 2024-07-16 14:59:27
2024-12-19 18:29:12 opt_multi_version     = 1
2024-12-19 18:29:12 opt_bitmain_ab        = 1
2024-12-19 18:29:12 mid_auto_gen          = 1
2024-12-19 18:29:12 opt_bitmain_work_mode = 0
2024-12-19 18:29:12 port 439 already exported
2024-12-19 18:29:12 port 454 already exported
2024-12-19 18:29:12 port 440 already exported
2024-12-19 18:29:12 port 455 already exported
2024-12-19 18:29:12 port 441 already exported
2024-12-19 18:29:12 port 456 already exported
2024-12-19 18:29:12 port 438 already exported
2024-12-19 18:29:12 port 453 already exported
2024-12-19 18:29:12 port 446 already exported
2024-12-19 18:29:12 port 445 already exported
2024-12-19 18:29:12 Note: front fan is power on!
2024-12-19 18:29:12 Note: rear fan is power on!
2024-12-19 18:29:12 start the http server
2024-12-19 18:29:12 httpserver:6060 started ok
2024-12-19 18:29:12 get test_loop_securely_find_asic_num failed
2024-12-19 18:29:12 abandon mix board!
2024-12-19 18:29:12 get mix boardname[0][BHB68701], name:BHB68701
2024-12-19 18:29:12 bad chain id = 3
2024-12-19 18:29:15 bad chain id = 3
2024-12-19 18:29:17 power on
2024-12-19 18:29:30 power off
2024-12-19 18:29:31 ==========================capability start==========================
2024-12-19 18:29:31 board num = 3
2024-12-19 18:29:31 board id = 0, chain num = 1
2024-12-19 18:29:31    chain id = 0
2024-12-19 18:29:31 board id = 1, chain num = 1
2024-12-19 18:29:31    chain id = 1
2024-12-19 18:29:31 board id = 2, chain num = 1
2024-12-19 18:29:31    chain id = 2
2024-12-19 18:29:31 ==========================capability end============================
2024-12-19 18:29:31 chain num = 3
2024-12-19 18:29:31 i2c chain = 0, master = 0x0, slave = 0xa0
2024-12-19 18:29:31 i2c chain = 1, master = 0x0, slave = 0xa2
2024-12-19 18:29:31 i2c chain = 2, master = 0x0, slave = 0xa4
2024-12-19 18:29:34 load chain 0 eeprom data
2024-12-19 18:29:37 load chain 1 eeprom data
2024-12-19 18:29:40 load chain 2 eeprom data
2024-12-19 18:29:40 eeprom load ret:0
2024-12-19 18:29:40 miner:BHB68701,board_name:BHB68701
2024-12-19 18:29:40 create thread get_nonce_and_register_thread
2024-12-19 18:29:40 fixed working voltage = 1360
2024-12-19 18:29:40 Chain

• PCB Version: 0x0100

2024-12-19 18:29:40 Chain

• BOM Version: 0x0000

2024-12-19 18:29:40 Chain [1] PCB Version: 0x0100
2024-12-19 18:29:40 Chain [1] BOM Version: 0x0000
2024-12-19 18:29:40 Chain [2] PCB Version: 0x0100
2024-12-19 18:29:40 Chain [2] BOM Version: 0x0000
2024-12-19 18:29:40 bad chain id = 3
2024-12-19 18:29:44 Fan check passed.
2024-12-19 18:29:44 init fan pid target=65
2024-12-19 18:29:44 max sensor num = 4
2024-12-19 18:29:44 asic_temperature_and_voltage_monitor_thread start...
2024-12-19 18:29:44 temperature_monitor_thread start...
2024-12-19 18:29:44 STATUS_INITED: soc init done!
2024-12-19 18:29:44 i2c chain = 0, master = 0x0, slave = 0x90
2024-12-19 18:29:44 i2c chain = 0, master = 0x0, slave = 0x98
2024-12-19 18:29:44 i2c chain = 1, master = 0x0, slave = 0x92
2024-12-19 18:29:44 i2c chain = 1, master = 0x0, slave = 0x9a
2024-12-19 18:29:44 i2c chain = 2, master = 0x0, slave = 0x94
2024-12-19 18:29:44 i2c chain = 2, master = 0x0, slave = 0x9c
2024-12-19 18:29:47 start to init...
2024-12-19 18:29:47 i2c_sim_init start
2024-12-19 18:29:47 i2c_sim_init end
2024-12-19 18:29:51 get power version failed
2024-12-19 18:29:51 check power version failed, use v2 protocal to try it again
2024-12-19 18:29:53 power open power_version = 0x6a
2024-12-19 18:29:57 power calibration data:
2024-12-19 18:29:57  9  B 92 41 
2024-12-19 18:29:57 A5 71 FC 47 
2024-12-19 18:29:57 29 26 EC DB 
2024-12-19 18:29:57 FF D3  0 FF 
2024-12-19 18:29:57  0 FE FF  0 
2024-12-19 18:29:57  0 FE  0 80 
2024-12-19 18:29:57 80 80 80 80 
2024-12-19 18:29:57 1F E0 3F 45 
2024-12-19 18:30:00 calibration data 1  15.520556    15.555556   
2024-12-19 18:30:00 calibration data 2  15.075111    15.111111   
2024-12-19 18:30:00 calibration data 3  14.628667    14.666667   
2024-12-19 18:30:00 calibration data 4  14.183222    14.222222   
2024-12-19 18:30:00 calibration data 5  13.737778    13.777778   
2024-12-19 18:30:00 calibration data 6  13.293333    13.333333   
2024-12-19 18:30:00 calibration data 7  12.848889    12.888889   
2024-12-19 18:30:00 calibration data 8  12.402444    12.444444   
2024-12-19 18:30:00 calibration data 9  11.957000    12.000000   
2024-12-19 18:30:00 power is Calibrated
2024-12-19 18:30:00 power sn:KLKT343BDJBBF2123
2024-12-19 18:30:00 enable_power_calibration,calibration date:211208.
2024-12-19 18:30:05 get power version failed
2024-12-19 18:30:05 check power version failed, use v2 protocal to try it again
2024-12-19 18:30:06 power type version: 0x006a
2024-12-19 18:30:06 power history status: -1
2024-12-19 18:30:08 disable power watchdog: 0x0000
2024-12-19 18:30:09 Initializing the power, please wait, this may take up to 2 minutes...
2024-12-19 18:30:39 Slept 30 seconds, diff = 1.
2024-12-19 18:30:49 set_voltage_by_steps to 1500.
2024-12-19 18:30:52 power on
2024-12-19 18:31:07 bad chain id = 3
2024-12-19 18:31:09 bitmain_get_sample_voltage:-1.000000 < 0
2024-12-19 18:31:09 ERROR_POWER_LOST: power voltage read failed, pls check!
2024-12-19 18:31:11 Get power code[0-3 4-7 8-11 12-13] 55aa0c0e 00000100 00050000 0d13, power_code:0x00000500
2024-12-19 18:31:11 reach max restart times
2024-12-19 18:31:13 start up min temp by 75a = 21
2024-12-19 18:31:23 Chain[0]: find 0 asic, times 0
2024-12-19 18:31:25 Version num 65536
2024-12-19 18:31:25 Mask num 0x1fffe000
2024-12-19 18:31:25 Note: addrInterval or corenum is not initialized.
2024-12-19 18:31:28 Chain[0]: find 0 asic, times 1
2024-12-19 18:31:32 Chain[0]: find 0 asic, times 2
2024-12-19 18:31:32 Chain 0 only find 0 asic, will power off hash board 0
2024-12-19 18:31:32 Sweep error string = J1:2.
2024-12-19 18:31:32 ERROR_ASIC_NUM: asic number is not right
2024-12-19 18:31:32 stop_mining: asic number is not right
2024-12-19 18:31:32 uninit_temp_info
2024-12-19 18:31:32 do not read temp anymore...
2024-12-19 18:31:32 uninit_asic_temp_vol_info
2024-12-19 18:31:32 do not read asic_temp_vol anymore...
2024-12-19 18:31:32 cancel thread thread_id_rd_nonce_reg
2024-12-19 18:31:32 ****power off hashboard****
2024-12-19 18:31:32 power off
2024-12-19 18:31:33 asic_temperature_and_voltage_monitor_thread exit
2024-12-19 18:31:33 temp monitor thread exit
2024-12-19 18:31:33 ERROR_SOC_INIT: soc init failed!
2024-12-19 18:31:33 reach max restart times
2024-12-19 18:54:22 ****power off hashboard****
2024-12-19 18:54:22 power off
2024-12-19 18:54:53 httpserver6060 quit!
2024-12-19 18:55:29 Open miner sn file /config/mac error
2024-12-19 18:55:29 Miner compile time: Thu Sep 26 11:39:05 CST 2024 type: Antminer T21 sn :HQDZF2UBDJBBA05ZR mac:
2024-12-19 18:55:31 This is fix-freq version
2024-12-19 18:55:31 Miner compile time: Thu Sep 26 11:39:05 CST 2024 type: Antminer T21
2024-12-19 18:55:31 Miner sn: HQDZF2UBDJBBA05ZR
2024-12-19 18:55:31 commit version: 62efe336 2024-08-15 13:07:46, build by: jenkins 2024-09-26 12:04:12
2024-12-19 18:55:31 opt_multi_version     = 1
2024-12-19 18:55:31 opt_bitmain_ab        = 1
2024-12-19 18:55:31 mid_auto_gen          = 1
2024-12-19 18:55:31 opt_bitmain_work_mode = 0
2024-12-19 18:55:31 port 439 already exported
2024-12-19 18:55:31 port 454 already exported
2024-12-19 18:55:31 port 440 already exported
2024-12-19 18:55:31 port 455 already exported
2024-12-19 18:55:31 port 441 already exported
2024-12-19 18:55:31 port 456 already exported
2024-12-19 18:55:31 port 438 already exported
2024-12-19 18:55:31 port 453 already exported
2024-12-19 18:55:31 port 446 already exported
2024-12-19 18:55:31 port 445 already exported
2024-12-19 18:55:31 Note: front fan is power on!
2024-12-19 18:55:31 Note: rear fan is power on!
2024-12-19 18:55:31 start the http server
2024-12-19 18:55:31 httpserver:6060 started ok
2024-12-19 18:55:31 get test_loop_securely_find_asic_num failed
2024-12-19 18:55:31 abandon mix board!
2024-12-19 18:55:31 get mix boardname[0][BHB68701], name:BHB68701
2024-12-19 18:55:31 bad chain id = 3
2024-12-19 18:55:34 bad chain id = 3
2024-12-19 18:55:36 power on
2024-12-19 18:55:49 power off
2024-12-19 18:55:51 ==========================capability start==========================
2024-12-19 18:55:51 board num = 3
2024-12-19 18:55:51 board id = 0, chain num = 1
2024-12-19 18:55:51    chain id = 0
2024-12-19 18:55:51 board id = 1, chain num = 1
2024-12-19 18:55:51    chain id = 1
2024-12-19 18:55:51 board id = 2, chain num = 1
2024-12-19 18:55:51    chain id = 2
2024-12-19 18:55:51 ==========================capability end============================
2024-12-19 18:55:51 chain num = 3
2024-12-19 18:55:51 i2c chain = 0, master = 0x0, slave = 0xa0
2024-12-19 18:55:51 i2c chain = 1, master = 0x0, slave = 0xa2
2024-12-19 18:55:51 i2c chain = 2, master = 0x0, slave = 0xa4
2024-12-19 18:55:54 load chain 0 eeprom data
2024-12-19 18:55:57 load chain 1 eeprom data
2024-12-19 18:56:00 load chain 2 eeprom data
2024-12-19 18:56:00 eeprom load ret:0
2024-12-19 18:56:00 miner:BHB68701,board_name:BHB68701
2024-12-19 18:56:00 create thread get_nonce_and_register_thread
2024-12-19 18:56:00 fixed working voltage = 1360
2024-12-19 18:56:00 Chain

• PCB Version: 0x0100

2024-12-19 18:56:00 Chain

• BOM Version: 0x0000

2024-12-19 18:56:00 Chain [1] PCB Version: 0x0100
2024-12-19 18:56:00 Chain [1] BOM Version: 0x0000
2024-12-19 18:56:00 Chain [2] PCB Version: 0x0100
2024-12-19 18:56:00 Chain [2] BOM Version: 0x0000
2024-12-19 18:56:00 bad chain id = 3
2024-12-19 18:56:03 Fan check passed.
2024-12-19 18:56:03 init fan pid target=65
2024-12-19 18:56:03 max sensor num = 4
2024-12-19 18:56:03 STATUS_INITED: soc init done!
2024-12-19 18:56:03 asic_temperature_and_voltage_monitor_thread start...
2024-12-19 18:56:03 temperature_monitor_thread start...
2024-12-19 18:56:03 i2c chain = 0, master = 0x0, slave = 0x90
2024-12-19 18:56:03 i2c chain = 0, master = 0x0, slave = 0x98
2024-12-19 18:56:03 i2c chain = 1, master = 0x0, slave = 0x92
2024-12-19 18:56:03 i2c chain = 1, master = 0x0, slave = 0x9a
2024-12-19 18:56:03 i2c chain = 2, master = 0x0, slave = 0x94
2024-12-19 18:56:03 i2c chain = 2, master = 0x0, slave = 0x9c
2024-12-19 18:56:06 start to init...
2024-12-19 18:56:06 i2c_sim_init start
2024-12-19 18:56:06 init gpio477
2024-12-19 18:56:06 init gpio476
2024-12-19 18:56:06 i2c_sim_init end
2024-12-19 18:56:11 get power version failed
2024-12-19 18:56:11 check power version failed, use v2 protocal to try it again
2024-12-19 18:56:13 power open power_version = 0x6a
2024-12-19 18:56:18 get power version failed
2024-12-19 18:56:18 power fw_version = 0x80000300
2024-12-19 18:56:22 power calibration data:
2024-12-19 18:56:22  9  B 92 41 
2024-12-19 18:56:22 A5 71 FC 47 
2024-12-19 18:56:22 29 26 EC DB 
2024-12-19 18:56:22 FF D3  0 FF 
2024-12-19 18:56:22  0 FE FF  0 
2024-12-19 18:56:22  0 FE  0 80 
2024-12-19 18:56:22 80 80 80 80 
2024-12-19 18:56:22 1F E0 3F 45 
2024-12-19 18:56:25 calibration data 1  15.520556    15.555556   
2024-12-19 18:56:25 calibration data 2  15.075111    15.111111   
2024-12-19 18:56:25 calibration data 3  14.628667    14.666667   
2024-12-19 18:56:25 calibration data 4  14.183222    14.222222   
2024-12-19 18:56:25 calibration data 5  13.737778    13.777778   
2024-12-19 18:56:25 calibration data 6  13.293333    13.333333   
2024-12-19 18:56:25 calibration data 7  12.848889    12.888889   
2024-12-19 18:56:25 calibration data 8  12.402444    12.444444   
2024-12-19 18:56:25 calibration data 9  11.957000    12.000000   
2024-12-19 18:56:25 power is Calibrated
2024-12-19 18:56:25 power sn:KLKT343BDJBBF2123
2024-12-19 18:56:25 enable_power_calibration,calibration date:211208.
2024-12-19 18:56:30 get power version failed
2024-12-19 18:56:30 check power version failed, use v2 protocal to try it again
2024-12-19 18:56:31 power type version: 0x006a
2024-12-19 18:56:31 power history status: -1
2024-12-19 18:56:33 disable power watchdog: 0x0000
2024-12-19 18:56:34 Initializing the power, please wait, this may take up to 2 minutes...
2024-12-19 18:57:04 Slept 30 seconds, diff = 0.
2024-12-19 18:57:14 set_voltage_by_steps to 1500.
2024-12-19 18:57:16 power on
2024-12-19 18:57:31 bad chain id = 3
2024-12-19 18:57:34 bitmain_get_sample_voltage:-1.000000 < 0
2024-12-19 18:57:34 ERROR_POWER_LOST: power voltage read failed, pls check!
2024-12-19 18:57:36 Get power code[0-3 4-7 8-11 12-13] 55aa0c0e 00000100 00050000 0d13, power_code:0x00000500
2024-12-19 18:57:36 reach max restart times
2024-12-19 18:57:37 Version num 65536
2024-12-19 18:57:37 Mask num 0x1fffe000
2024-12-19 18:57:37 Note: addrInterval or corenum is not initialized.
2024-12-19 18:57:38 start up min temp by 75a = 21
2024-12-19 18:57:48 Chain[0]: find 0 asic, times 0
2024-12-19 18:57:52 Chain[0]: find 0 asic, times 1
2024-12-19 18:57:57 Chain[0]: find 0 asic, times 2
2024-12-19 18:57:57 Chain 0 only find 0 asic, will power off hash board 0
2024-12-19 18:57:57 Sweep error string = J1:2.
2024-12-19 18:57:57 ERROR_ASIC_NUM: asic number is not right
2024-12-19 18:57:57 stop_mining: asic number is not right
2024-12-19 18:57:57 uninit_temp_info
2024-12-19 18:57:57 do not read temp anymore...
2024-12-19 18:57:57 uninit_asic_temp_vol_info
2024-12-19 18:57:57 do not read asic_temp_vol anymore...
2024-12-19 18:57:57 cancel thread thread_id_rd_nonce_reg
2024-12-19 18:57:57 ****power off hashboard****
2024-12-19 18:57:57 power off
2024-12-19 18:57:57 asic_temperature_and_voltage_monitor_thread exit
2024-12-19 18:57:58 temp monitor thread exit
2024-12-19 18:57:58 ERROR_SOC_INIT: soc init failed!
2024-12-19 18:57:58 reach max restart times
2024-12-19 19:01:22 ****power off hashboard****
2024-12-19 19:01:22 power off
2024-12-19 19:01:53 httpserver6060 quit!
2024-12-19 19:02:28 Open miner sn file /config/mac error
2024-12-19 19:02:28 Miner compile time: Thu Sep 26 11:39:05 CST 2024 type: Antminer T21 sn :HQDZF2UBDJBBA05ZR mac:
2024-12-19 19:02:30 This is fix-freq version
2024-12-19 19:02:30 Miner compile time: Thu Sep 26 11:39:05 CST 2024 type: Antminer T21
2024-12-19 19:02:30 Miner sn: HQDZF2UBDJBBA05ZR
2024-12-19 19:02:30 commit version: 62efe336 2024-08-15 13:07:46, build by: jenkins 2024-09-26 12:04:12
2024-12-19 19:02:30 opt_multi_version     = 1
2024-12-19 19:02:30 opt_bitmain_ab        = 1
2024-12-19 19:02:30 mid_auto_gen          = 1
2024-12-19 19:02:30 opt_bitmain_work_mode = 0
2024-12-19 19:02:30 port 439 already exported
2024-12-19 19:02:30 port 454 already exported
2024-12-19 19:02:30 port 440 already exported
2024-12-19 19:02:30 port 455 already exported
2024-12-19 19:02:30 port 441 already exported
2024-12-19 19:02:30 port 456 already exported
2024-12-19 19:02:30 port 438 already exported
2024-12-19 19:02:30 port 453 already exported
2024-12-19 19:02:30 port 446 already exported
2024-12-19 19:02:30 port 445 already exported
2024-12-19 19:02:30 Note: front fan is power on!
2024-12-19 19:02:30 Note: rear fan is power on!
2024-12-19 19:02:30 start the http server
2024-12-19 19:02:30 httpserver:6060 started ok
2024-12-19 19:02:30 get test_loop_securely_find_asic_num failed
2024-12-19 19:02:30 abandon mix board!
2024-12-19 19:02:30 get mix boardname[0][BHB68701], name:BHB68701
2024-12-19 19:02:30 bad chain id = 3
2024-12-19 19:02:33 bad chain id = 3
2024-12-19 19:02:35 power on
2024-12-19 19:02:49 power off
2024-12-19 19:02:50 ==========================capability start==========================
2024-12-19 19:02:50 board num = 3
2024-12-19 19:02:50 board id = 0, chain num = 1
2024-12-19 19:02:50    chain id = 0
2024-12-19 19:02:50 board id = 1, chain num = 1
2024-12-19 19:02:50    chain id = 1
2024-12-19 19:02:50 board id = 2, chain num = 1
2024-12-19 19:02:50    chain id = 2
2024-12-19 19:02:50 ==========================capability end============================
2024-12-19 19:02:50 chain num = 3
2024-12-19 19:02:50 i2c chain = 0, master = 0x0, slave = 0xa0
2024-12-19 19:02:50 i2c chain = 1, master = 0x0, slave = 0xa2
2024-12-19 19:02:50 i2c chain = 2, master = 0x0, slave = 0xa4
2024-12-19 19:02:53 load chain 0 eeprom data
2024-12-19 19:02:56 load chain 1 eeprom data
2024-12-19 19:03:00 load chain 2 eeprom data
2024-12-19 19:03:00 eeprom load ret:0
2024-12-19 19:03:00 miner:BHB68701,board_name:BHB68701
2024-12-19 19:03:00 create thread get_nonce_and_register_thread
2024-12-19 19:03:00 fixed working voltage = 1360
2024-12-19 19:03:00 Chain

• PCB Version: 0x0100

2024-12-19 19:03:00 Chain

• BOM Version: 0x0000

2024-12-19 19:03:00 Chain [1] PCB Version: 0x0100
2024-12-19 19:03:00 Chain [1] BOM Version: 0x0000
2024-12-19 19:03:00 Chain [2] PCB Version: 0x0100
2024-12-19 19:03:00 Chain [2] BOM Version: 0x0000
2024-12-19 19:03:00 bad chain id = 3
2024-12-19 19:03:03 Fan check passed.
2024-12-19 19:03:03 init fan pid target=65
2024-12-19 19:03:03 max sensor num = 4
2024-12-19 19:03:03 STATUS_INITED: soc init done!
2024-12-19 19:03:03 asic_temperature_and_voltage_monitor_thread start...
2024-12-19 19:03:03 temperature_monitor_thread start...
2024-12-19 19:03:03 i2c chain = 0, master = 0x0, slave = 0x90
2024-12-19 19:03:03 i2c chain = 0, master = 0x0, slave = 0x98
2024-12-19 19:03:03 i2c chain = 1, master = 0x0, slave = 0x92
2024-12-19 19:03:03 i2c chain = 1, master = 0x0, slave = 0x9a
2024-12-19 19:03:03 i2c chain = 2, master = 0x0, slave = 0x94
2024-12-19 19:03:03 i2c chain = 2, master = 0x0, slave = 0x9c
2024-12-19 19:03:06 start to init...
2024-12-19 19:03:06 i2c_sim_init start
2024-12-19 19:03:06 init gpio477
2024-12-19 19:03:06 init gpio476
2024-12-19 19:03:06 i2c_sim_init end
2024-12-19 19:03:11 get power version failed
2024-12-19 19:03:11 check power version failed, use v2 protocal to try it again
2024-12-19 19:03:12 power open power_version = 0x6a
2024-12-19 19:03:17 get power version failed
2024-12-19 19:03:17 power fw_version = 0x80000300
2024-12-19 19:03:21 power calibration data:
2024-12-19 19:03:21  9  B 92 41 
2024-12-19 19:03:21 A5 71 FC 47 
2024-12-19 19:03:21 29 26 EC DB 
2024-12-19 19:03:21 FF D3  0 FF 
2024-12-19 19:03:21  0 FE FF  0 
2024-12-19 19:03:21  0 FE  0 80 
2024-12-19 19:03:21 80 80 80 80 
2024-12-19 19:03:21 1F E0 3F 45 
2024-12-19 19:03:24 calibration data 1  15.520556    15.555556   
2024-12-19 19:03:24 calibration data 2  15.075111    15.111111   
2024-12-19 19:03:24 calibration data 3  14.628667    14.666667   
2024-12-19 19:03:24 calibration data 4  14.183222    14.222222   
2024-12-19 19:03:24 calibration data 5  13.737778    13.777778   
2024-12-19 19:03:24 calibration data 6  13.293333    13.333333   
2024-12-19 19:03:24 calibration data 7  12.848889    12.888889   
2024-12-19 19:03:24 calibration data 8  12.402444    12.444444   
2024-12-19 19:03:24 calibration data 9  11.957000    12.000000   
2024-12-19 19:03:24 power is Calibrated
2024-12-19 19:03:24 power sn:KLKT343BDJBBF2123
2024-12-19 19:03:24 enable_power_calibration,calibration date:211208.
2024-12-19 19:03:29 get power version failed
2024-12-19 19:03:29 check power version failed, use v2 protocal to try it again
2024-12-19 19:03:30 power type version: 0x006a
2024-12-19 19:03:30 power history status: -1
2024-12-19 19:03:32 disable power watchdog: 0x0000
2024-12-19 19:03:33 Initializing the power, please wait, this may take up to 2 minutes...
2024-12-19 19:04:03 Slept 30 seconds, diff = 0.
2024-12-19 19:04:13 set_voltage_by_steps to 1500.
2024-12-19 19:04:16 power on
2024-12-19 19:04:31 bad chain id = 3
2024-12-19 19:04:33 bitmain_get_sample_voltage:-1.000000 < 0
2024-12-19 19:04:33 ERROR_POWER_LOST: power voltage read failed, pls check!
2024-12-19 19:04:35 Get power code[0-3 4-7 8-11 12-13] 55aa0c0e 00000100 00050000 0d13, power_code:0x00000500
2024-12-19 19:04:35 reach max restart times
2024-12-19 19:04:37 start up min temp by 75a = 21
2024-12-19 19:04:38 Version num 65536
2024-12-19 19:04:38 Mask num 0x1fffe000
2024-12-19 19:04:38 Note: addrInterval or corenum is not initialized.
2024-12-19 19:04:47 Chain[0]: find 0 asic, times 0
2024-12-19 19:04:52 Chain[0]: find 0 asic, times 1
2024-12-19 19:04:56 Chain[0]: find 0 asic, times 2
2024-12-19 19:04:56 Chain 0 only find 0 asic, will power off hash board 0
2024-12-19 19:04:56 Sweep error string = J1:2.
2024-12-19 19:04:56 ERROR_ASIC_NUM: asic number is not right
2024-12-19 19:04:56 stop_mining: asic number is not right
2024-12-19 19:04:56 uninit_temp_info
2024-12-19 19:04:56 do not read temp anymore...
2024-12-19 19:04:56 uninit_asic_temp_vol_info
2024-12-19 19:04:56 do not read asic_temp_vol anymore...
2024-12-19 19:04:56 cancel thread thread_id_rd_nonce_reg
2024-12-19 19:04:56 ****power off hashboard****
2024-12-19 19:04:56 power off
2024-12-19 19:04:57 asic_temperature_and_voltage_monitor_thread exit
2024-12-19 19:04:57 temp monitor thread exit
2024-12-19 19:04:57 ERROR_SOC_INIT: soc init failed!
2024-12-19 19:04:57 reach max restart times
2015-01-01 00:00:15 Open miner sn file /config/mac error
2015-01-01 00:00:15 Miner compile time: Thu Sep 26 11:39:05 CST 2024 type: Antminer T21 sn :HQDZF2UBDJBBA05ZR mac:
2015-01-01 00:00:17 This is fix-freq version
2015-01-01 00:00:17 Miner compile time: Thu Sep 26 11:39:05 CST 2024 type: Antminer T21
2015-01-01 00:00:17 Miner sn: HQDZF2UBDJBBA05ZR
2015-01-01 00:00:17 commit version: 62efe336 2024-08-15 13:07:46, build by: jenkins 2024-09-26 12:04:12
2015-01-01 00:00:17 opt_multi_version     = 1
2015-01-01 00:00:17 opt_bitmain_ab        = 1
2015-01-01 00:00:17 mid_auto_gen          = 1
2015-01-01 00:00:17 opt_bitmain_work_mode = 0
2015-01-01 00:00:17 port 439 already exported
2015-01-01 00:00:17 port 454 already exported
2015-01-01 00:00:17 port 440 already exported
2015-01-01 00:00:17 port 455 already exported
2015-01-01 00:00:17 port 441 already exported
2015-01-01 00:00:17 port 456 already exported
2015-01-01 00:00:17 port 438 already exported
2015-01-01 00:00:17 port 453 already exported
2015-01-01 00:00:17 port 446 already exported
2015-01-01 00:00:17 port 445 already exported
2015-01-01 00:00:17 Note: front fan is power on!
2015-01-01 00:00:17 Note: rear fan is power on!
2015-01-01 00:00:17 start the http server
2015-01-01 00:00:17 httpserver:6060 started ok
2015-01-01 00:00:17 get test_loop_securely_find_asic_num failed
2015-01-01 00:00:17 abandon mix board!
2015-01-01 00:00:17 get mix boardname[0][BHB68701], name:BHB68701
2015-01-01 00:00:17 bad chain id = 3
2015-01-01 00:00:20 bad chain id = 3
2015-01-01 00:00:22 power on
2024-12-19 19:39:11 power off
2024-12-19 19:39:12 ==========================capability start==========================
2024-12-19 19:39:12 board num = 3
2024-12-19 19:39:12 board id = 0, chain num = 1
2024-12-19 19:39:12    chain id = 0
2024-12-19 19:39:12 board id = 1, chain num = 1
2024-12-19 19:39:12    chain id = 1
2024-12-19 19:39:12 board id = 2, chain num = 1
2024-12-19 19:39:12    chain id = 2
2024-12-19 19:39:12 ==========================capability end============================
2024-12-19 19:39:12 chain num = 3
2024-12-19 19:39:12 i2c chain = 0, master = 0x0, slave = 0xa0
2024-12-19 19:39:12 i2c chain = 1, master = 0x0, slave = 0xa2
2024-12-19 19:39:12 i2c chain = 2, master = 0x0, slave = 0xa4
2024-12-19 19:39:15 load chain 0 eeprom data
2024-12-19 19:39:19 load chain 1 eeprom data
2024-12-19 19:39:22 load chain 2 eeprom data
2024-12-19 19:39:22 eeprom load ret:0
2024-12-19 19:39:22 miner:BHB68701,board_name:BHB68701
2024-12-19 19:39:22 create thread get_nonce_and_register_thread
2024-12-19 19:39:22 fixed working voltage = 1360
2024-12-19 19:39:22 Chain

• PCB Version: 0x0100

2024-12-19 19:39:22 Chain

• BOM Version: 0x0000

2024-12-19 19:39:22 Chain [1] PCB Version: 0x0100
2024-12-19 19:39:22 Chain [1] BOM Version: 0x0000
2024-12-19 19:39:22 Chain [2] PCB Version: 0x0100
2024-12-19 19:39:22 Chain [2] BOM Version: 0x0000
2024-12-19 19:39:22 bad chain id = 3
2024-12-19 19:39:25 Fan check passed.
2024-12-19 19:39:25 init fan pid target=65
2024-12-19 19:39:25 max sensor num = 4
2024-12-19 19:39:25 asic_temperature_and_voltage_monitor_thread start...
2024-12-19 19:39:25 temperature_monitor_thread start...
2024-12-19 19:39:25 STATUS_INITED: soc init done!
2024-12-19 19:39:25 i2c chain = 0, master = 0x0, slave = 0x90
2024-12-19 19:39:25 i2c chain = 0, master = 0x0, slave = 0x98
2024-12-19 19:39:25 i2c chain = 1, master = 0x0, slave = 0x92
2024-12-19 19:39:25 i2c chain = 1, master = 0x0, slave = 0x9a
2024-12-19 19:39:25 i2c chain = 2, master = 0x0, slave = 0x94
2024-12-19 19:39:25 i2c chain = 2, master = 0x0, slave = 0x9c
2024-12-19 19:39:27 start to init...
2024-12-19 19:39:27 i2c_sim_init start
2024-12-19 19:39:27 init gpio477
2024-12-19 19:39:27 init gpio476
2024-12-19 19:39:27 i2c_sim_init end
2024-12-19 19:39:32 get power version failed
2024-12-19 19:39:32 check power version failed, use v2 protocal to try it again
2024-12-19 19:39:33 power open power_version = 0x6a
2024-12-19 19:39:38 get power version failed
2024-12-19 19:39:38 power fw_version = 0x80000300
2024-12-19 19:39:42 power calibration data:
2024-12-19 19:39:42  9  B 92 41 
2024-12-19 19:39:42 A5 71 FC 47 
2024-12-19 19:39:42 29 26 EC DB 
2024-12-19 19:39:42 FF D3  0 FF 
2024-12-19 19:39:42  0 FE FF  0 
2024-12-19 19:39:42  0 FE  0 80 
2024-12-19 19:39:42 80 80 80 80 
2024-12-19 19:39:42 1F E0 3F 45 
2024-12-19 19:39:45 calibration data 1  15.520556    15.555556   
2024-12-19 19:39:45 calibration data 2  15.075111    15.111111   
2024-12-19 19:39:45 calibration data 3  14.628667    14.666667   
2024-12-19 19:39:45 calibration data 4  14.183222    14.222222   
2024-12-19 19:39:45 calibration data 5  13.737778    13.777778   
2024-12-19 19:39:45 calibration data 6  13.293333    13.333333   
2024-12-19 19:39:45 calibration data 7  12.848889    12.888889   
2024-12-19 19:39:45 calibration data 8  12.402444    12.444444   
2024-12-19 19:39:45 calibration data 9  11.957000    12.000000   
2024-12-19 19:39:45 power is Calibrated
2024-12-19 19:39:45 power sn:KLKT343BDJBBF2123
2024-12-19 19:39:45 enable_power_calibration,calibration date:211208.
2024-12-19 19:39:50 get power version failed
2024-12-19 19:39:50 check power version failed, use v2 protocal to try it again
2024-12-19 19:39:52 power type version: 0x006a
2024-12-19 19:39:52 power history status: -1
2024-12-19 19:39:53 disable power watchdog: 0x0000
2024-12-19 19:39:54 Initializing the power, please wait, this may take up to 2 minutes...
2024-12-19 19:40:24 Slept 30 seconds, diff = 0.
2024-12-19 19:40:34 set_voltage_by_steps to 1500.
2024-12-19 19:40:37 power on

I will post the logs in about 15h here.

I did check t he logs and before it started to restart over and over with this warning code i saw that the hash rate decrease to 100th (33 or 37th/ board).

i will check also the boards to see if there is a LED on them and come back with more info

Thank you

Hello,

My Bitmain T21 190th miner stopped mining and shows a Warning Info:
Warning code J1:2
"Check whether chain1 connection is normal, update the firmware to the latest version, replace the hashboard, or return to factory for repair"

I update the firmware, rebooted several time the miner
the power 3phase is ok (over 226V / Phase)

Does somebody knows how to fix this issue ?

Thank you

ca sa valoreze 1BTC- 600.000$ marketcap-ul lui trebuie sa fie ~ 17.600.000BTC x 600.000$=> 10.560.000.000.000 $ adica fix jumatate din PIB ul Americii ... pai cine o sa bage atatia bani doar in BTC ?
 BTC si alte cripto vor avea preturi mari doar daca vor avea si o intrebuintare a blockchainului lor din spate  si daca la nivel mondial se vor printa multi $ si E (+ o inflatie mare)
daca peste 10 ani un BTC ajunge 600.000$ inseamna ca un Logan o sa fie 30.000E si noi vom avea iarasi salarii exprimate in milioane de lei

Salutare,

 De cateva saptamani tot vad pe youtube cum se promoveaza placile programabile FPGA!
O placa costa intre 3600$ si 4500E
Daca i se pune 64GB DDR4 poate produce intre 40$ si 60$
Tot pe Bitcointalk se vorbeste destul de serios despre aceste placi si cum ca s-ar vinde impreuna cu un miner special facut pt placa, adica fiecare lot de placi sa se vanda cu un miner speical si sa mineze intr un animit pool ...au facut niste calcule de performante si de hashrate ale placilor din lot ca sa nu mareasca dificultatea algoritmului pe urma.

https://fpga.land/collections/vcu1525/products/vcu1525-withmods?variant=9991785316467

https://www.youtube.com/watch?v=x9DJ18y8LcI&t=129s

 2 Surse Zalman 850W la 450 ron buc (garantie 35 luni )
 2 surse 850w Chieftech la 400 ron buc ( garantie 23 luni) 
 1  CPU AMD FX6100 6 Core  250 RON garantie 35 luni
 1 CPU AMD FX4300 Quadcore 220  garantie 35 luni
   Cabluri "Y" cu 24 pini pentru a putea lega 2 surse la o pl de baza 30 ron
  Testere surse PC 30 ron
cablu alimentare pci 6 pini la 2x 8 pini 10 ron
 4 hdd sata 160GB 8mb 30 ron buc

- Risere 006c cu cablu albastru - 33 ron 
 2 Surse Zalman 850W la 450 ron buc (garantie 35 luni )
 2 surse 850w Chieftech la 400 ron buc ( garantie 23 luni) 
 1  CPU AMD FX6100 6 Core  250 RON garantie 35 luni
 1 CPU AMD FX4300 Quadcore 220  garantie 35 luni
   Cabluri "Y" cu 24 pini pentru a putea lega 2 surse la o pl de baza 30 ron
  Testere surse PC 30 ron
 4 hdd sata 160GB 8mb 30 ron buc

Au mai ramas urmatoarele :

- Risere 006c cu cablu albastru - 33 ron 
 3 Surse Zalman 850W la 450 ron buc (garantie 35 luni )
 2 surse 850w Chieftech la 400 ron buc ( garantie 23 luni) 
 1 Pl. Baza Gigabyte 970A-DS3P Sk AM3+ ( suporta 5 placi video) 250 ron cu garantie 35 luni
 3  CPU AMD FX6100 6 Core  250 RON + 2 CPU AMD FX4300 Quadcore 220 ( toate cu garantie 35 luni )
   Cabluri "Y" cu 24 pini pentru a putea lega 2 surse la o pl de baza 30 ron
  Teste surse PC 30 ron
 4 hdd sata 160GB 8mb 30 ron buc

Se vand urmatoarele :

- Risere 006c cu cablu albastru - 40 ron  ( peste 20 buc pretul scade la 35 ron ) 
 3 Surse Zalman 850W la 450 ron buc (garantie 35 luni )
 2 surse 850w Chieftech la 400 ron buc ( garantie 23 luni) 
 3 Pl. Baza Gigabyte 970A-DS3P Sk AM3+ ( suporta 5 placi video) 250 ron cu garantie 35 luni
 3  CPU AMD FX6100 6 Core  250 RON + 2 CPU AMD FX4300 Quadcore 220 ( toate cu garantie 35 luni )
   Cabluri "Y" cu 24 pini pentru a putea lega 2 surse la o pl de baza 30 ron
  Teste surse PC 40 ron
 3 x 4Gb RAM Kingston DDR3 la 1600Mhz - 100ron/buc
 6 hdd sata 160GB 8mb 30 ron buc ( merg perfect pt minat)

Predare personala in Bucuresti
Toate componentele sunt noi si au fot folosite 1-2 sapt

Va rog sa sunati pentru orice intrebare la 0727.875.287
-= Pentru mai multe produse trimit si in tara =-