The 8.8v right now is running the best on the bitmain 1600w PSU.

For the S9i I would try 800Mhz and see what temps your getting should be 90-100c. This will be like a 20% boost

For the 13.5 I would Try 725Mhz.

For the 14th I would try somewhere between 725 and 800mhz and check your hw errors and see what runs best once warmed up.

If your machines power off and don't reboot unplug the psu for a little bit. That means it drew to much power and the psu went into protect mode so lower the frequency if that happens although I have not had that issues with 8.8v only 8.9v and 9v on the 1600w.

I also cannot get back to stock. Cant even SSH into my miner after I reinstalled the Bitmain Firmware. The standard credentials are root as user and admin as the password. Im getting Access Denied using those credentials.

Dollemizer please advise asap!

With the second firmware does 750m work without it rebooting? Or does it reboot with both firmware regardless at 750m?

Do you have a bitmain 1600w psu because if it is drawing to much power and the psu is causing it to reboot that could be the cause of it shutting down. If you used the bitmain psu and you go over the voltage the psu will shut down and go into protect mode for a few minutes unless you reset it. The other cause is the miner needs more voltage to run at that mhz. If that is the case I can make a bminer at 8.9v or even try at 8.7volts. (I don't think 8.7volts is going workout to well though and cause lots of HW errors but I can build it)

That was very garbled... My question is does 750m not work with both firmware and do you have bitmain psu so we can see if it is just drawing to much power and that is why it is resetting since you have no meter to tell power draw and if we overload it and it goes in protect mode we will know. (my meter comes tomorrow so I can make a decent guess as well)

I don't see any reason why the 13.5 will not run at 750m as I have successfully gotten it to run at 18.5th with two psus. We might just need to tweak some setting in bminner. I did notice however one of your hashboard is throwing errors and not your others. If one hashboard is weaker than the rest and has issues it will cause the whole miner to act up if one board is not as fast as the rest.

Did lowering the MHz by 1 or 2 levels stop it from shutting itself down. Do you by any chance have a meter to see what the 13.5 is drawing?

Did you set it to 800mhz. Did the psu get tripped and that's why it shut down or the s9 crash. I am waiting on my new clamp meter to measure actual power draw since I can't seem to find mine but I have not tripped the 1600w psu at 800mhz. You might have a slightly less efficient one since my 800mhz benchmark was done with a 14th unit. Try to 787.50mhz or 793.75mhz since if it is tripping at the 2-3 minute mark it is tripping after 2-3 minutes of mining and it might have been a slight fluctuation in power draw since I removed a lot of the crap that makes the boot up time take so long on the s9. Try the second download link it runs it at less than 9volts and runs at 8.8v https://drive.google.com/open?id=1TkW-BB0SKl5daIeEA5XziU_UvNQpzyAd It should work better on 1800w psu at the 9v one sits right along the max power draw.

The following is good to run at 800mhz and gets 17th/s and is STABLE and will almost max out the bitmain 1600w psu.

all works fine.

https://www.youtube.com/watch?v=Eq9WeXQlDwU&t=139s

Known Issues:
• Hashboard do not report temps but will still mine. Possible good and bad. If you have a hashboard with no temp reading it may work just fine with this mod. The miner will still stop mining if it overheats.

Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=1a middle offset=-112
read failed, old value: Chain[5] Chip[62] local Temp=62
Chain[5] Chip[62] middle Temp=38
218 fix Chain[5] Chip[62] middle Temp = 97
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=1a middle offset=-111
Chain[6] Chip[62] local Temp=61
Chain[6] Chip[62] middle Temp=33
218 fix Chain[6] Chip[62] middle Temp = 96
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=1a middle offset=-100
Chain[7] Chip[62] local Temp=61
Chain[7] Chip[62] middle Temp=33
218 fix Chain[7] Chip[62] middle Temp = 96
Done read temp on Chain[7]
set FAN speed according to: temp_highest=62 temp_top1[PWM_T]=97 temp_top1[TEMP_POS_LOCAL]=62 temp_change=0 fix_fan_steps=0
FAN PWM: 74
read_temp_func Done!
CRC error counter=0

Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=1a middle offset=27
Chain[5] Chip[62] local Temp=58
Chain[5] Chip[62] middle Temp=133
Special fix Chain[5] Chip[62] middle Temp = 73
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=1a middle offset=27
Chain[6] Chip[62] local Temp=55
Chain[6] Chip[62] middle Temp=141
Special fix Chain[6] Chip[62] middle Temp = 70
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=1a middle offset=27
Chain[7] Chip[62] local Temp=60
read failed on Chain[7] Chip[62] middle Temp old value:74
Special fix Chain[7] Chip[62] middle Temp = 75
Done read temp on Chain[7]
set FAN speed according to: temp_highest=60 temp_top1[PWM_T]=60 temp_top1[TEMP_POS_LOCAL]=60 temp_change=1 fix_fan_steps=0
FAN PWM: 68
read_temp_func Done!
CRC error counter=0

EAG is an ambitious and wide-ranging blockchain project, aimed at disrupting the local merchant cryptocurrency payment business. This is a worldwide open source e-commerce marketplace platform that anomynously connects subscribers with local merchants that do not accept cryptocurrencies.
....

We have to free up server resources for new coins by delisting some coins which have consistently low trading volume.
The following coins will be removed on 07.11.2017 if their average trading volume for the last month has not exceeded 0.5 BTC/day (15 BTC for last 30 days):

SixEleven [611], Alphabit [ABC], AnarchistsPrime [ACP], AdvancedInternetBlock [AIB], Altcoin [ALT], BitBay [BAY], BighanCoin [BHC], BoostCoin [BOST], BritCoin [BRIT], BitLuckCoin [BTLC], Bitquark [BTQ], CaliphCoin [CALC], CryptoJacksCoin [CJ], CoreCoin [CRC], CereiPayCoin [CRPC], Crypto [CTO], DA$ [DAS], DragonDigitalCoin [DDC], DT Token [DRACO], Droidz [DRZ], GA Coin [GAC], Eclipse [EC], Etherex [ETX], FastCash [FCH], FujiCoin [FJC], FutCoin [FUTC], President Johnson [GARY], GoldCoin [GLD], GlobalTradeCoin [GLTC], GoldUnionCoin [GUC], HEAT ledger [HEAT], JIO Token [JIO], Kingdom Coin [KGDC], KiloCoin [KLC], LEOcoin [LEO], MALCoin [MALC], MobileCash [MBL], EncryptoTel [ETT], Macro [MCR], Mooncoin [MOON], NoLimitCoin 2.0 [NLC2], NovaCoin [NVC], OpinionCoin [OPNC], OTCCoin [OTX], Polybius Token [PLBT], PiZZAcoin [PIZZA], President Trump [PRES], Pesobit [PSB], Robocoin [ROBO], SIGMA coin [SGC], Sikka [SIKKA], SilverCoin [SVC], T-coin [TCOIN], TengRi [TERI], Terra [TERRA], TeslaCoilCoin [TESLA], TerraCoin [TRC], WexCoin [WEX], Xaurum [XAUR], Humaniq [HMQ], Bitcoin U.F. [XB], BlackPearl [XBP], ForeverCoin [XFC], GoldenBird [XGB], XNCCoin [XNC], InternetOfThings [XOT], Bonanza [XZA], Zilbercoin [ZBCN], Zennies [ZENI], SmileyCoin [SMLY].

Please, trade, sell or withdraw these coins before removal date, after which retrieval of any remaining balances for these coins will not be possible anymore.
We will not remove coins which will reach minimum trading volume requirement.

We have to free up server resources for new coins by delisting some coins which have consistently low trading volume.
The following coins will be removed on 07.11.2017 if their average trading volume for the last month has not exceeded 0.5 BTC/day (15 BTC for last 30 days):

SixEleven [611], Alphabit [ABC], AnarchistsPrime [ACP], AdvancedInternetBlock [AIB], Altcoin [ALT], BitBay [BAY], BighanCoin [BHC], BoostCoin [BOST], BritCoin [BRIT], BitLuckCoin [BTLC], Bitquark [BTQ], CaliphCoin [CALC], CryptoJacksCoin [CJ], CoreCoin [CRC], CereiPayCoin [CRPC], Crypto [CTO], DA$ [DAS], DragonDigitalCoin [DDC], DT Token [DRACO], Droidz [DRZ], GA Coin [GAC], Eclipse [EC], Etherex [ETX], FastCash [FCH], FujiCoin [FJC], FutCoin [FUTC], President Johnson [GARY], GoldCoin [GLD], GlobalTradeCoin [GLTC], GoldUnionCoin [GUC], HEAT ledger [HEAT], JIO Token [JIO], Kingdom Coin [KGDC], KiloCoin [KLC], LEOcoin [LEO], MALCoin [MALC], MobileCash [MBL], EncryptoTel [ETT], Macro [MCR], Mooncoin [MOON], NoLimitCoin 2.0 [NLC2], NovaCoin [NVC], OpinionCoin [OPNC], OTCCoin [OTX], Polybius Token [PLBT], PiZZAcoin [PIZZA], President Trump [PRES], Pesobit [PSB], Robocoin [ROBO], SIGMA coin [SGC], Sikka [SIKKA], SilverCoin [SVC], T-coin [TCOIN], TengRi [TERI], Terra [TERRA], TeslaCoilCoin [TESLA], TerraCoin [TRC], WexCoin [WEX], Xaurum [XAUR], Humaniq [HMQ], Bitcoin U.F. [XB], BlackPearl [XBP], ForeverCoin [XFC], GoldenBird [XGB], XNCCoin [XNC], InternetOfThings [XOT], Bonanza [XZA], Zilbercoin [ZBCN], Zennies [ZENI], SmileyCoin [SMLY].

Please, trade, sell or withdraw these coins before removal date, after which retrieval of any remaining balances for these coins will not be possible anymore.
We will not remove coins which will reach minimum trading volume requirement.

We have to free up server resources for new coins by delisting some coins which have consistently low trading volume.
The following coins will be removed on 07.11.2017 if their average trading volume for the last month has not exceeded 0.5 BTC/day (15 BTC for last 30 days):

SixEleven [611], Alphabit [ABC], AnarchistsPrime [ACP], AdvancedInternetBlock [AIB], Altcoin [ALT], BitBay [BAY], BighanCoin [BHC], BoostCoin [BOST], BritCoin [BRIT], BitLuckCoin [BTLC], Bitquark [BTQ], CaliphCoin [CALC], CryptoJacksCoin [CJ], CoreCoin [CRC], CereiPayCoin [CRPC], Crypto [CTO], DA$ [DAS], DragonDigitalCoin [DDC], DT Token [DRACO], Droidz [DRZ], GA Coin [GAC], Eclipse [EC], Etherex [ETX], FastCash [FCH], FujiCoin [FJC], FutCoin [FUTC], President Johnson [GARY], GoldCoin [GLD], GlobalTradeCoin [GLTC], GoldUnionCoin [GUC], HEAT ledger [HEAT], JIO Token [JIO], Kingdom Coin [KGDC], KiloCoin [KLC], LEOcoin [LEO], MALCoin [MALC], MobileCash [MBL], EncryptoTel [ETT], Macro [MCR], Mooncoin [MOON], NoLimitCoin 2.0 [NLC2], NovaCoin [NVC], OpinionCoin [OPNC], OTCCoin [OTX], Polybius Token [PLBT], PiZZAcoin [PIZZA], President Trump [PRES], Pesobit [PSB], Robocoin [ROBO], SIGMA coin [SGC], Sikka [SIKKA], SilverCoin [SVC], T-coin [TCOIN], TengRi [TERI], Terra [TERRA], TeslaCoilCoin [TESLA], TerraCoin [TRC], WexCoin [WEX], Xaurum [XAUR], Humaniq [HMQ], Bitcoin U.F. [XB], BlackPearl [XBP], ForeverCoin [XFC], GoldenBird [XGB], XNCCoin [XNC], InternetOfThings [XOT], Bonanza [XZA], Zilbercoin [ZBCN], Zennies [ZENI], SmileyCoin [SMLY].

Please, trade, sell or withdraw these coins before removal date, after which retrieval of any remaining balances for these coins will not be possible anymore.
We will not remove coins which will reach minimum trading volume requirement.

Next Payout: 16:37 EDT @ 16:37 EDT server down @ now: Next Payout: 20:45 EDT

When will we receive payment?

Up

Upgrade completed. Downtime was ~15m at most. Any issues you see that are new let me know.

Cheers

ccminer-x64 -a skunk -o stratum+tcp://mine.zpool.ca:8433 -u BMnB8DM5LXVZDTgr5E82toYZkiuLYCVPWW -p c=sigt --cpu-priority=5 -d 0 -i 25
pause

You can also use any valid wallet address from any of the coins we mine. This feature has had minimal testing so use at your own risk