MatthewV: When you say lower voltage in bios what do you mean? Undervolt  - Directly on the VBios Config? (My Exxperience with Bios Modding was at the time of the 8800GTX and the propose was for Games not for mining, so if you could elaborate on this  I would appreciate).

In the mean time I have found some one placing their memory timing from a Rx580 and all the timings were exactly the same of my original memory timing as my one is a 8gb hynix.... so I yried the timing on the card the: 777000000000000022AA1C00B56A6D46C0551017BE8E060C006AE6000C081420EA8900AB0300000 01B162C31C0313F17
 I tried on the 1725 2000 2250 and is going up to 25.5 stable I would say.... even do my card is Rx470 its working for now... 45 to 50 degrees celsius......

Still no way close to the 28/29mhz objective.... If anyone has a new timing of config to improve the hashrate with stability let me know... I would say I am doing what I can for my self and community as I am leaving behind every step..... (I am not a quiter so I be around for little nit more I would say)

 

Hi Guys SO I have made some progress since  early on.....
I took the risk of trying again.... this time more calm.... So, I have backup the bios with ATIWinFlash..... I copy the timings from 1750 to 2000 and to 2250....
Restarted a few times and applied the patch the bios check and looks like it worked. I have three cards I have flashed one by one and restarted after each time and at the end after doing this to all three I have applied the patch and restarted again....

Using Trixx I have setup to GPU clock 1150 - Memory 2000 Power Limit 0% GPU Voltage -96 give or take this is the average for the cards with a few tweaks here and there..... (Still have a long way to run to find out the best specs)

It's giving me a 24mh each so all this for 7mhz more...

Its looking stable however I am sure its possible to find a better timing and get a better performance... Overall the all system is pulling 400W from the wall... This shown by a Watt Meter on the main plug.... so same wattage however a little bit more hash.... I just though maybe would be able to help someone on the same problem .... Still as a said before not perfect and I might try other timing later on...
 

Any gool soul to help out a new miner for the eth community?
[/quote]
Well you might hope, but they are thousands like you, guys who know how to do good bios mod wouldn't do anything else
[/quote]

Well.... MatthewV would you be able to help me out with this.... i have seen that you have tried to help a few with similar problems .... 

I would say i need to have a better understanding of the checking bios of relive and hiw to bupass this and of course the timings as i have this new strap  2250.... that makes me doubt of all other guides....

This were made for mining i was hoping to have more info on this what i cannot find☹️☹️

Hi guys i will say that i am quite new to the mining world and i have already made the first mistake.... i believe...

I have the following
Gugabyte b350 gaming AM4
Ryden 3 1200
Amd asus R230 to connect a monitor(poor choice of mother board or graphic cards)
3x Sapphire Rx470 8gb Nitro Mining edition hynix memory
Psu 850w

First issue my cards dont have monitor connection... so r230 was bought obly to be able to configurate this...

By default cards hit the 600w from de wall(all shstem) gives me 20.300mhz

I have change the clocks using trixx and i am getting 21.5mhz on two cards and 20.3 on the third one and the whole system is pulling 400w what is better but not perfect. The manufacture says 24 to 27 what is not happening... therefore i need to mod the bios to try to get better hashes...


I have read and watched multiple videos about modding cards and similar cards i have even tried once(i though i jad bricked card)

So first of all.... all the videos i saw the card had straps up to 2000 my one has and additional one 2250... in all videos the timing that was added to 1725 to 2000 started with a 777 my card on the same places has a 999 on the timing...
Still tried to copy paste the 1725 to the 2000 and to the 2250.... windows restarted with a blue screen about some errors..... the card was not readable as the drivers were says unknow on the gpuz..... atiwinflash would not star normally and would appear error reading rom. Using Cmd i was able to flash back to backup and after unistalling the drivers and card and reinstalling everything i got it working again..... before flashing back i tried the amd dagpatch for the checking bios and nothing worked.... i definetely i need more hashrate on this outherwise i will be losing on the cards investement..... can some one help me with the timing and config to make this run for last i am using thr latet driver 17.7.2.....

Any gool soul to help out a new miner for the eth community?