 Show Posts
|
|
Pages: [1]
|
|
Wallet is not synchronized. why?
|
|
|
|
|
Help me.
The balance in my wallet has disappeared.
There is a backup of wallet.dat.
Is there anything else I need to restore it?
|
|
|
|
Hi! I typed "masternode start" at the debug console, the following sentences appeared. "Not capable masternode: Can not detect valid external address. Make sure to use IPv4 address only." What should I do?  In vivo.conf add: externalip=[your external ip address] If you're doing this at home and not on a VPS you also need to open port 12845 on your router and point it at your internal PC so that inbound traffic can get to your node. masternode successfully My masternode tab has no notation. All masternode tab has the notation "pre_enable". Is this OK? can you check your MN in the explorer: http://vivo.explorerz.top:3003/masternodes Put your MN IP and see if it comes up and what the status is? There is my MN IP on it. The status is ENABLE. Thanks for the people who replied.  |
|
|
|
Hi! I typed "masternode start" at the debug console, the following sentences appeared. "Not capable masternode: Can not detect valid external address. Make sure to use IPv4 address only." What should I do? In vivo.conf add: externalip=[your external ip address] If you're doing this at home and not on a VPS you also need to open port 12845 on your router and point it at your internal PC so that inbound traffic can get to your node. masternode successfully My masternode tab has no notation. All masternode tab has the notation "pre_enable". Is this OK? |
|
|
|
Hi! I typed "masternode start" at the debug console, the following sentences appeared. "Not capable masternode: Can not detect valid external address. Make sure to use IPv4 address only." What should I do? |
|
|
|
|
Characters of "master node" are displayed on the official site.
Does anyone know more information?
|
|
|
|
|
I appreciate all the kind people.
That problem was solved.
kind people=shveicar ,BogdanCo ,Heavyiron
Please contact me if you cooperated with my problem.
I will give you a tip.
Please paste the DMD's address in the mail.
|
|
|
|
Hello! help me  Importing and exporting Private Keys form DMD Wallet 2.0 to 3.0 When importing, only half of Wallet Balance is sent. Some remain on the previous wallet. v 2: 10090 DMD → V 3: 5080 DMD I have only one address in V2 Wallet. What kind of problems are there? Please provide your DMD address so that we can verify your balance in the block explorer. After confirming the balance in Block Explorer, it was 5080 DMD. I'm talking about the fact that the balance of your address DMD v 2.0 we can be checked in the browser blocks https://chainz.cryptoid.info/dmd-v2/I understand. The balance display of v2 wallet is 10093 DMD. On the Block Chain Explorer, the balance is only 5080DMD. On September 3 I sent 62DMD to bittrex. At this time, 4982 DMD seems to be sent to somewhere. I do not remember sending it to this address. address: There is a possibility that it was stolen. When you sent the 62 DMD to Bittrex it's possible that the rest of your big pile to split and 4982 DMD went into a new generated address. Go to your old wallet and use coin control to see if the 4982 DMD are not there. If yes, then you have to dump your private key of the address dNXQdyhKBTzU2X61pDVoHnr4qzmj8G2Bwm and import it into the new wallet. Thanks to you, it seems to be settled. I will give you a tip if I solve the problem. |
|
|
|
Hello! help me Importing and exporting Private Keys form DMD Wallet 2.0 to 3.0 When importing, only half of Wallet Balance is sent. Some remain on the previous wallet. v 2: 10090 DMD → V 3: 5080 DMD I have only one address in V2 Wallet. What kind of problems are there? Please provide your DMD address so that we can verify your balance in the block explorer. After confirming the balance in Block Explorer, it was 5080 DMD. I'm talking about the fact that the balance of your address DMD v 2.0 we can be checked in the browser blocks https://chainz.cryptoid.info/dmd-v2/I understand. The balance display of v2 wallet is 10093 DMD. On the Block Chain Explorer, the balance is only 5080DMD. On September 3 I sent 62DMD to bittrex. At this time, 4982 DMD seems to be sent to somewhere. I do not remember sending it to this address. There is a possibility that it was stolen. |
|
|
|
Hello! help me Importing and exporting Private Keys form DMD Wallet 2.0 to 3.0 When importing, only half of Wallet Balance is sent. Some remain on the previous wallet. v 2: 10090 DMD → V 3: 5080 DMD I have only one address in V2 Wallet. What kind of problems are there? Please provide your DMD address so that we can verify your balance in the block explorer. thank you. After confirming the balance in Block Explorer, it was 5080 DMD. |
|
|
|
Hello! help me Importing and exporting Private Keys form DMD Wallet 2.0 to 3.0 When importing, only half of Wallet Balance is sent. Some remain on the previous wallet. v 2: 10090 DMD → V 3: 5080 DMD I have only one address in V2 Wallet. What kind of problems are there? |
|
|
|
Hello! Help me I am struggling to set up the master node. When trying to start the master node, the following sentence is displayed. "Not capable masternode: Could not connect to xx.xxx.xx.xxx" (x = IP address) What is the problem? How can I solve it?
-support team
hi, I checked, but the firewall is not blocking "linda-qt.exe". Are there other problems? ****=hide -------------my linda conf----------------------- rpcuser=****** rpcpassword=********** rpcport=93821 rpcallowip=127.0.0.1 daemon=1 server=1 listenonion=0 maxconnections=256 masternode=1 masternodegenkey=68Z************************************************ masternodeprivkey=Pdy************************************************* masternodeaddr=**.***.***.***:33820 addnode=185.82.200.183 addnode=185.183.98.138 addnode=185.137.97.15 addnode=104.236.248.131 addnode=207.231.77.78 addnode=142.129.224.40 addnode=94.75.47.43 addnode=45.55.212.165 addnode=167.114.121.103 addnode=lindaminingpool.ddns.net addnode=64.180.19.218 addnode=5.141.209.230 addnode=5.9.112.62 |
|
|
|
Hello! Help me I am struggling to set up the master node. When trying to start the master node, the following sentence is displayed. "Not capable masternode: Could not connect to xx.xxx.xx.xxx" (x = IP address) What is the problem? How can I solve it? |
|
|
|
|
