 Show Posts
|
|
Pages: [1] 2 3 4 »
|
Wooooow, 500 million premind  . This joke is not funny anymore, it smells like a scam. Good luck to those who fall into the trap Agreed. Premine is way too high. |
|
|
|
|
I am patiently awaiting the new release to allow over clocking the new Bitmain Asic Boost LPM firmware. Thanks for all you do taserz!
|
|
|
|
|
I thought ASIC BOOST was supposed to give increased pool side hash rate?
|
|
|
|
|
I'm out. Back to Slush Pool. I will mine there until the end of the month, and if we don't get the recovery by then I am throwing in the towel.
|
|
|
|
starting to get worried here fellas  What exactly are you worried about? We have 140PH on board and are only just over 100% diff on the current block. It has been a few says since our last block. However, you have successfully reassured me. |
|
|
|
starting to get worried here fellas |
|
|
|
|
What the heck? Where did all the hash rate go? I didn't get the memo.
|
|
|
|
Nice run boys!  |
|
|
|
|
just think positive block producing thoughts...
|
|
|
|
|
Greetings CK, I have found a new home here with my paltry 60T. I love the concept of the pool. This is how I would have made a pool had I ever been inclined.
High performance, Fair, and Minimalist.
I am mining from Thailand connected to the North American IP. I guess that is my best choice from here no?
|
|
|
|
|
it defaulted to DHCP. duhhhhhhhhhhh
|
|
|
|
a couple I can't tell, but the other two are reading between 100 and 110 the best as I can tell. Pool side looks like this: Hashrate 1hr 1d Total Shares Last Share
1 15.5T 13.0T 13.2T 460,179,743 a few seconds ago
2 16.6T 13.2T 13.4T 469,457,488 a few seconds ago
3 16.1T 13.9T 14.0T 489,358,099 a few seconds ago
4 16.1T 12.8T 12.7T 429,664,692 a few seconds ago
|
|
|
|
Correct.
Do you recommend I do that? Or should I just go back to stock given my temp issues? |
|
|
|
Why are you using autofreq? with fw from post 1 you can change just about anything. If memory serves me correctly the very first instruction is get rid of autofreq.
If I flash fixed freq at this juncture will I need to replace bminer again? |
|
|
|
|
Sent my 4 machines back to hosting. Three set @ 725 MHZ are ceasing to hash randomly. I have remotely rebooted them. One was ceasing to hash so frequently I lowered it from 725 to 650. Now that one appears to be periodically resetting itself. I am running the Autofreq FW on all four. I think I may have heat issues. Any suggestions? I need these babies to stabilize.
|
|
|
|
2 per minute is right around where you want to keep it. Anything more you should tune it down. But let it run for a while the hw errors tend to stop after it gets going for a bit. I have had stock s9's do 200 hw errors in an hour.
But I found once you get it running for a bit it tends to slow down.
725 isa what many were finding is best for 13.5 and 14 s9. Some 14th s9 were going pretty high.
Yes. I am watching it on the pool side too. Those HW errors seem to kill a lot of shares. |
|
|
|
|
737.00 gives same (similar) results as 725. Seems like 725 is my optimal. (i am running autofreq firmware 255)
|
|
|
|
OK. I am at 750MHZ, 91C, 15,309.53 RT. HW errors are about 2 per minute. Too high I think.
Check that. HW error rate decreasing. Looks stable now. 22 minutes in.
HMM. HW error rate back to 2 per minute. 27 minutes in. |
|
|
|
|
