Show Posts
|
Pages: [1] 2 »
|
i'am looking for a water cooling kit. can someone give me a hint where to buy one?
|
|
|
Ich habe noch zwei hier rumliegen mit je 70 KH/s. Wieviel würdest du hierfür bieten?
was für welche sind es denn?
|
|
|
egal ob usb oder standalone. möchte damit altcoins minen und habe free power.
|
|
|
Does this prove that Ukyo acted fraudulently? He obviously had access to the wallet to make withdrawals and he used my funds to pay out another user?
Not really because ukyo claimed some time that he can do withdraws manually. This stopped then though. So this withdraw might be from a time when the manual withdraws still were possible. Of course you are in a special situation. The coins you deposited belonged to you and ukyo only had them in escrow. Its a shares wallet of course but normally those coins would be attached to you and werent owned be weexchange. So at a possible court case you might claim that he gave your coins to others to solve weexchange debts. Strictly spoken coins that were deposited and users bought shares with it wouldnt belong to them anymore. But coins that werent used to buy anything would still belong to someone. Of course that only would help you as long as there is a chance to get the coins back. I think ukyo has never done one single withdraw manually. Ukyo has lied as he said he does withdraws manually. I tell You what Uyko did: He lost 94% of our Coins. Afterwards he transfered the rest of the coins to the claim portal to withdraw weex users 6% of their coins.
|
|
|
back to the only solution to find out what was going on. we need to know where all the bitcoins are gone. exist a programm that shows me where my bitcoins gone? or have i do this by hand( i try, but it is very difficulty to look at the tree of addresses (outputs) that spans always more branches) is it possible to follow the route of my bitcoins ( I send to weex) when i look at the blockchain? ok, if it is possible then we have to try. It is the only way to find the truth! is it possible to follow the route of my bitcoins ( I send to weex) when i look at the blockchain?
Yes it is. What you will find is a tree of addresses (outputs) that spans always more branches... "Is it possible to interpret the data and find out where it's gone?" Hardly, but you can try
|
|
|
ok, if it is possible then we have to try. It is the only way to find the truth! is it possible to follow the route of my bitcoins ( I send to weex) when i look at the blockchain?
Yes it is. What you will find is a tree of addresses (outputs) that spans always more branches... "Is it possible to interpret the data and find out where it's gone?" Hardly, but you can try
|
|
|
is it possible to follow the route of my bitcoins ( I send to weex) when i look at the blockchain?
|
|
|
is it a scam when i lost 94% of my BTC?
|
|
|
the coins are lost. there will never be a payout
|
|
|
Username WeExchange ID Amount Time Stamp
Falko0815 DkcQSadTbyuqcuOD2R4a2UqB0zvnGPZW 13.3 2013-10-28 12:36:12
|
|
|
WeExchange The Trusted Solution to Exchange Online
|
|
|
It would be very helpful if people would stop making up stories about a scam unless there is actual evidence for it… Moreover, it would be extremely helpful if the people whose transactions went through, would post a confirmation in this thread.
no one is posting a confirmation, because not a single transaction went through.
|
|
|
I think it's time to think about a negative trust
|
|
|
ich hab nen blade rev 2.0. ich hab das problem, dass alle chips auf einmal nur xxxxxx anzeigen. ich hab jetzt mal den strom gemessen gemäß folgendem Bild: nur liegen bei mir an der stelle wo 1.05 V anliegen sollen 12V an. Ist das beim rev 2.0 normal, oder könnte das der Fehler sein, warum alle chips nur noch xxx haben? Auch scheint es so, dass ich die volt zahl nicht verändern kann, egal in welche richtung ich drehe, es verändert sich nichts.
|
|
|
Waiting for BTC withdrawal stuck in "processing state" with open ticket on WeExchange for 8 days already with no reaction from anybody.
Same probs, for 10 days Status:processing, no btc withdrawl
|
|
|
still waiting
|
|
|
same prob, hab jetzt schon factory reset probiert, anderes netztteil, das blade komplett zerlegt und die chips angeschaut(schauen alle ok aus), chips durchgemessen(sind alle ok) laut FC könnte es am power modul liegen( also das größere der beiden steckteile)
|
|
|
hey wie führe ich den factory reset richtig aus? muss das blade wenn ich den jumper auf 2-3 setze unter strom sein, oder stromlos? und muß ich danach den jumper auf 1-2 setzten?
|
|
|
|