Does anyone have a list of command lines for the different mining pools and switches to use on this.  Here is the command line I am going to try to use under Simple Mining (SM) but I do not know if it is correct or not.  I will try to report back here tomorrow or the day after.

optiminer-equihash -s us-east.equihash-hub.miningpoolhub:20570 -a equihash200_9 \ -u BinanceDepositAddress.$AlexZcash

I just enter my deposit wallet in the Binance Deposit Address.  I am not sure if the start to the config line is right or if it needs something else.  I will try it tomorrow and see what happens.

Alex

I am having a problem that I have not seen on the forums.
Using claymore 11.7 on 4 rigs.  Rig 1 runs happily along and seldom needs any resets.  It is overclocked the most.
My new rig has 12 cards on an Asus B250 MB and sapphire nitro+ cards.  bios modded to 1180 core, 2150 or 2130 memory 940 volts and memory timings 1500 for 1625 and up, but I use the 1625 or even 1750 timings for 2000.

The rig can has for hours okay but then some of the cards will drop to super low rates like 1 - 5 Mh or even drop out all together.  MB is flashed to 1010 which is the newest. It should not be temp because that is reached in the first hour and these do not drop out for well after that time.  I am fairly good with computer hardware and I don't think there is a problem there because I am seeing this on 3 rigs but not rig 1.

Comments?

I am using the simpleminer Linux setup.  I have dropped the simpleminer Linux software onto a 16GB flash device and I boot from there.  It is using the Claymore v 10 setup.  In both cases all of the video cards are the same with the same bios flashed into them.  My rig is 6 x MSI 580 8GB Gaming-X cards and the second rig is 6 or 7 (wall power permitting) MSI 580 8GB Armor cards.  Becasue the video cards are all the same, and even manufactured sequentially they are identical so they should not be the issue.

The problem will not be with the operating system or motherboard I think of this problem would be more wide spread.  I should note that my rig is running on 2 x 4GB memory while the Armor rig is 2x8GB memory so memory is not an issue either. 

With regards to Mining Doc's comments regarding the slot numbering I actually think taht the PCIe slot 1 is not what is called GPU0 by the computer.  Somewhere I saw a picture of the layout of some motherboard and GPU0 was actually in the middle of the board, not where you would expect it.  In any case i will be working on this tonight so I will report back if I find the answer.

I can flip the two 16GB flash devices between the two boards and the problem persists with one rig having issues with GPU3 and the other with GPU0.  One always down exactly 5 Mh and the other spirals down to nothing over time.  Teh HDMI dongle did not help at all and just made that GPU drop to 0 instantly.

I will report back.

I am using two different rigs both based on the 19 card Asus Mining board, G3930 Processor, 4GB ram and 6 MSI 580 8GB cards running Claymore V10.  Both are a little different in problem.  On Rig one, 5 cards are running at 30 Mh nicely but the extra one starts at 30 Mh but then rolls down to 15 Mh and rebooting does not help.  It is the GPU3 and whatever card that is in the system.  Changing cards, risers etc always gives what is identified as GPU3 the problem.  On rig 2 all of them are running at 27.5 Mh but the first GPU0 always runs at 22 Mh.  If you swap out video cards the next card then runs at 22 Mh.  It is not the card on either case.

I take off video to my screen from the onboard video, not plugging into any one card.  If I try to plug an HDMI dongle into the problem card it will roll down to 0 Mh rate.

Does anyone know why this is happening.  It does not follow the card,  riser or anything else.  If you have a config that addresses this problem, can you paste it in this thread.  Does anyone have a link that would show the GPU numbering for that Asus Motherboard so I can figure out which slot is GPU0 or GPU3.  I know it is not as simple as the first slot = GPU0.

I am using both Blockchain and Poloniex.  Poloniex because a friend recommended it.  I find it hard to understand and I will have to have my friend show me around on sunday.  BlockChain is really easy to understand and nicely setup for me here in North America.

I do have a problem on sync up times etc.  I am using Simpleminer under their free startup system and have had it running on and off for a few days now.  I have been up for the last 24 hours making Eth. only.  My question is this.  Although I have been only going at 133 MH rate, which I know is pretty slow, I was still expecting to see at least 0.00000000001 Eth. coin in my account.  I have zero.  One person who is not too up on this said they will only pay into my account at times and not continually and that is why I have nothing in the account.  Can someone tell me if I am doing something wrong or if it just takes this long to get any deposit.  I do not want to be running my rig, and making zero on it.  I would rather correct this problem before I go any further. It all looks like it is running well but if it is not making any money then I need a cheaper way to heat the house.    thanks for any reponses.   I will check back tomorrow.