After 4 months ! my eth deposit has been credited. Now it is worth 1/3 of amount back then however it does not really matter. So now I want to withdraw it . Could you please advise what is the safest currency to exchange it and to withdraw it afterwards as it looks like liqui is not good with ETH.

Also when i log in with my desktop, the exchange is not loading properly. I tried with 3 different computers. With my mobile, it load correctly however do not see option for witdraw. Thank you in advance for any help.

Best Regards

Around 28C. Yes it was quite strange to me as well. Fanatic26 could you send me a link to older versions firmware that I can use and are tested to work well.

Hi guys,

I started the changing firmware process as the hash board once again started to stop.

I found difficult to find this verson Antminer-S9-all-201704280713-autofreq-user-Update2UBI-NF.tar.gz as Bimain have removed it from support page. I found one on internet however not sure if this is the same to which Bitmaxz is reffering as now after the new firmward


Miner Type   Antminer S9
Hostname   antMiner
Model   GNU/Linux
Hardware Version   16.8.1.3
Kernel Version   Linux 3.14.0-xilinx-gb190cb0-dirty #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
File System Version   Sat Apr 29 20:01:20 EDT 2017
Logic Version   
BMminer Version   2.0.0
Uptime   15


 the machine is working on much higher degrees around 100 and the rear fan does not go bewond 5280  rpm while my other machines which are with November firmware are around 70-80 degrees and the rear fans are blowing with 6120 rpm.

Could you please advise

Thank you BitMaxz for taking time to look into this.

Here are the details. Please let me know if I should do additional screenshots.

Hardware Version   16.8.1.3
Kernel Version   Linux 3.14.0-xilinx-ge8a2f71-dirty #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
File System Version   Fri Nov 17 17:37:49 CST 2017
Logic Version   S9_V2.54
BMminer Version   2.0.0

Thank you ccgllc and BitMaxz for your suggestions.

Yes I am running on 220 V and the other 6 machines which I have are just fine. I will try to reflash with  Aprils firmware but I will will wait till the board stops again as of now it is working ok.

What worries me about the temperature is not the degrees but that middle board temperature is just 1 degree close of the first hashboard ( usually first board is 5-6 degrees warmer than the middle board). And when it exceeds first board in temperature, then it is when it stops . May be there is some automatic precaution set up in Antminer's settings for that..not sure.

..the other board is working much higher freq and at some point is stop hashing ?

Please see below the screenshots. For the past 10days 4 times second board is stopping and the asic need to be powered off so it can start hashing with all 3 boards. Do you this that reset the miner or installing different firmware will help ( i am with the latest one, Nov 2017)
https://ibb.co/kbVTpc
https://ibb.co/f7D3Nx
https://ibb.co/bLHKvH
https://ibb.co/e9GCFH

So the things I have done up to now:
- I changed the power unit, again to Bitmain's one from a different miner
- Changed the Ethernet cable

For 12 hours, it is running smoothly, however I have the feeling that it will stop soon again as the temperature of the chips are like
73
72
72

while the rest of the miners have temps like
75
68
67

and second board could once again exceed the temperature of board 1 which is when the hashboard is stopping

Other reason I could think off , if there is dust inside the asic and need to be cleaned however it is within warranty and Bitmain support insist if the problem persist not to open the miner but to send it to them for repair which means that I will lost 1-2 months turnaround time.

Any suggestion will be greatly appreciated !

No reply for me as well unfortunately. At least they could have put warning message not to deposit ETH from Bitstamp. I would know I would use my wallet to do so.

 

Just heads up for people that want to use Liqui. Know that It can turn very bad for you if you choose that exchange.

Usually I am very patient, I understand that all exchanges have issue scaling their services to much bigger number of customers, however this Liqui exchange is ridiculous.

I have made ETH depost (0x08b050891c4c21c64e91c7c408f54964b2d257b98b3788bcfe462d5ec9aa84c0) on 9th of January and 13 days later, I still do not have it. I have opened a ticket, however the response I get is that they have asked for tr. ID although I have already provided them to them. At that time the token that I wanted to buy SRN was worth 2 USD. Now is 3.20 .

Meanwhile by that time I feel very brave that this is just temporary issue, I have also deposit BTC and the transaction went fine. So with one word you can have luck, but if something goes wrong do not expect issue to be resolved easily and fast.

Still I hope for positive resolution and if there are updates I will post them here. I have also twit them as suggested here