Hi folks.
Im really pretty new to the bitcoin community, but as my experiencie as linux advanced user, i think this its quite disturbing
first of all, some data:
Linux terminus 3.2.0-4-amd64 #1 SMP Debian 3.2.46-1 x86_64 GNU/Linux
00:00.0 RAM memory: NVIDIA Corporation MCP65 Memory Controller (rev a3)
00:01.0 ISA bridge: NVIDIA Corporation MCP65 LPC Bridge (rev a3)
00:01.1 SMBus: NVIDIA Corporation MCP65 SMBus (rev a1)
00:01.2 RAM memory: NVIDIA Corporation MCP65 Memory Controller (rev a1)
00:02.0 USB controller: NVIDIA Corporation MCP65 USB Controller (rev a3)
00:02.1 USB controller: NVIDIA Corporation MCP65 USB Controller (rev a3)
00:06.0 Ethernet controller: NVIDIA Corporation MCP65 Ethernet (rev a3)
00:07.0 Audio device: NVIDIA Corporation MCP65 High Definition Audio (rev a1)
00:08.0 PCI bridge: NVIDIA Corporation MCP65 PCI bridge (rev a1)
00:09.0 IDE interface: NVIDIA Corporation MCP65 IDE (rev a1)
00:0a.0 IDE interface: NVIDIA Corporation MCP65 SATA Controller (rev a3)
00:0d.0 PCI bridge: NVIDIA Corporation MCP65 PCI Express bridge (rev a1)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:06.0 RAID bus controller: Adaptec AAC-RAID (rev 01)
01:0e.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)
02:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Juniper [Radeon HD 5700 Series]
02:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI Juniper HDMI Audio [Radeon HD 5700 Series]
Default Adapter - ATI Radeon HD 5700 Series
Core (MHz) Memory (MHz)
Current Clocks : 157 300
Current Peak : 960 1445
Configurable Peak Range : [500-960] [1200-1445]
GPU load : 0%
CPU: AMD Opteron 1810, 4 gb ram.
PSU 500 W
Now, the problem.
If i run a cgminer (i tried with 2.61, 2.2.1 and 3.2.1) and run a benchmark, i got around 118 mh/s. Litecoin the same.
The weird part is, even i configured a current peak of 960 and 1445, it only goes up to 500 and 1200.
cgminer version 2.6.1 - Started: [2013-06-22 13:06:16]
--------------------------------------------------------------------------------
(5s):58.1 (avg):91.8 Mh/s | Q:0 A:0 R:0 HW:0 E:0% U:0.0/m
TQ: 2 ST: 2 SS: 0 DW: 0 NB: 0 LW: 0 GF: 0 RF: 0
Connected to Benchmark without LP as user Benchmark
Block: (null)... Started:
--------------------------------------------------------------------------------
(P)ool management (G)PU management (s)ettings (D)isplay options (Q)uit
GPU 0: | 36.7/ 91.8Mh/s | A:0 R:0 HW:0 U:0.00/m I: 3
--------------------------------------------------------------------------------
[2013-06-22 13:06:16] Started cgminer 2.6.1
[2013-06-22 13:06:18] Disabling extra threads due to dynamic mode.
[2013-06-22 13:06:18] Tune dynamic intensity with --gpu-dyninterval
[2013-06-22 13:06:19] Thread 1 being disabled
Default Adapter - ATI Radeon HD 5700 Series
Core (MHz) Memory (MHz)
Current Clocks : 500 1200
Current Peak : 960 1445
Configurable Peak Range : [500-960] [1200-1445]
GPU load : 92%
You see?
Im using SDK 2.8 and catalyst 12.10.
If i run this aticonfig -pxl i got that:
PowerXpress: Integrated GPU is active (Power-Saving mode).
Even if i run aticonfig --px-dgpu i got no answer and the card still on that mode.
So my options are as follows:
-Defective card
-Bad driver & SDK combination
-Uhm?
Strange thing, if i plug a 4770 and boot up the computer, it makes one beet and get the POST. If i put this one, the server tries to booth several times until i got the beep and get the POST.
Its and headless server, so i dont know if i should configure something.
Thanks in advance!