Hi, I might be interested in this depending on the details.

Hello everyone,

     I'm looking for people interested in building a mining group around NY/NJ (Anywhere else is also OK). I'm good with Hardware and Software and I have ~70GH/s hardware with me. If anyone is interested in joining force with hardware or financially please PM me. I can take care of all the equipment installation and maintenance. I have all the necessary networking and power supply equipment.

I'm not sure if anybody would be interested in this, I just wanted to reach out and see if anyone is interested.

Thank you
yl

USB:

ylame; 10; 1.6; 1Pu2rc1sgQ5Gttc6HfGCSJB9GruAAqw4Us

I have put together a low power Linux computer using Rapsberry Pi, pre-configured to run cgminer for erupter blocks, stratum proxy for ASIC, erupter blade, p2pool to run your own pool. I can customize it as per your need and have any needed software pre-installed.

It runs on 5v ~500mA



PM me for details and pricing.

Thank you

I mixed up my passwords and tried to log in couple of time's and now when I try to go to http://www.btcguild.com/ I get

Error 1006
Access denied
What happened?
The owner of this website (www.btcguild.com) has banned your IP address ().

To get your IP unbanned just send an email to webmaster@btcguild.com with you IP address, which you can find out from http://www.myipaddress.com/show-my-ip-address/ and wait for someone to reply.



Thanks everyone
yl

Thank you, this seems to have reduced the number of errors in the log. I still see couple of them, but much less. I don't have QoS set on my network but the p2pool and the blade are on the same LAN. Would it be of any help to setup QoS?

Thank you

I'm trying to use ASICMiner erupter blade, which only supports getwork with p2pool. I can't get it to work.

When I have the blade connected directly to p2pool, I see lot's of
Worker <name> submitted share with hash > target:" in my P2Pool logs

So I setup a stratum proxy which work fine with 50btc.com but when I use it with the p2pool, the blades get no work. It sit's ideal.

What am I missing? Are there any specific version's that should be using?

Thanks a lot for the info Guy's. Currently I have stratum proxy working and pointing to http://50btc.com. I can see blade mining properly. but if change the stratum proxy to connect to p2pool, the blade stops working, it gets no work. So it seems like p2pool issue. But if I connect the blade directly to the p2pool then the blade gets work but all work that is submitted this way causes an error "share hash > target" in the p2pool logs.

When I run the stratum proxy with verbose on, I see the following error in it's log

INFO proxy client_service.handle_event # New job 124360118874900773260691942609319532920 for prevhash 794b3be3, clean_jobs=True
2013-09-02 09:57:28,720 DEBUG protocol protocol.writeJsonResponse # < {"error": null, "id": 916376870, "result": null}

Is there any specific version for stratum proxy I should be using?

Has anyone able to use Erupter Blade with p2pool?

I have tried the following setup

p2pool -- Stratum Proxy -- BE Blade

But when I set it up in this way, blade does not receiver any work. It just sits ideal.

p2pool -- BE Blade

 I get worker share hash > target error.

Hi, Thanks for the reply. I do have stratum proxy in place.

p2pool -- Stratum Proxy -- BE Blade

But when I set it up in this way, blade does not receiver and work. It just sits ideal.

Is it possible to use erupter blade with p2pool and stratum proxy? How can I setup stratum proxy and how to monitor the mining effort?

Thank you

Pledging 5 shares

Hi,

      Is anyone interested in doing a group investment around NY/NJ area? I can do all the setup and maintain it and I have Power supplies and networking equipment.

Thank you for your interest.

Oh really, where can I buy it from for 3.5BTC?

Thank you

I have 5 erupter blade’s in hand just recently received for building a new rig for a customer. The customer has ran into financial problems and cannot complete the pending payment immediately. So have decided to sell it.

Speed:	Each blade runs at 10GH/s which totals to 50GH/s. It can be safely overclocked with cooling to run at 13GH/s which total to 65GH/s. If you want I can overclock them for you.
Price:	1200/blade which totals to $6,000

 
 What’s included in this price:

• I have 2 fans attached to each of the blades, total of 10 fan which are more than enough to keep the blade running cool.
• I also have a custom build frame for the blade’s, if you want I’ll include it for free.
• Five 4pin molex connectors for connecting the blades to PSU

 What’s not included:

• Power supply is not include in this price, but if you want I have a brand new OCZ 750W modular power supply which I can add for additional $90
• Brand new Netgear 8 Port Gigabit switch with 6 CAT5 cables for additional $80

I’m located around NJ/NY area and I prefer local pickup as the rig is already assembled and I don’t want to take it apart. Also if you want you can test it and see it running.

PM or Post here if you are interested. The rig is available and ready for pick.

Thank you for your interest.

I'm interested in this and ready to invest as well. I just build a 60GH/s rig using ASIC. I can get more but out of funds now. I can build up the whole rig. I'm from NY.

Thank you
yl

No there are no X's in Chip's section. The 2R2 are running hot. I have cooling on the heat skin. Is that normal? Do I need additional cooling?

Thank you

Hello All,

I'm trying to setup erupter blade, it constantly restarts.

Any idea, what am I missing?

Thank you
yl

Hello,

      I have been mining bitcoins alt coins using GPU rig. I'm planning to buy more GPU's. Is it worth buying?

Thank you all for all the posts and all the knowledge sharing.... Keep it up and I'll try to jump in too as I can...