Show Posts
|
Pages: [1] 2 »
|
Hello all,
One of my cards dips about 2 mh every one to three minutes then picks right back up. It doesn't seem to affect mining. Is this a issue I should be concerned about? Will it affect my gear in a bad way or be bad for overall shares?
Any guidance would be appreciated.
|
|
|
Hello,
I am using smOS (simple mining OS). I have a card that drops exactly 2 mh every 2 or 3 minutes. I see it on claymore. Then it goes right back up and goes perfect. Everything is mining fine and properly, it happened after on OC. I know it is a bit unstable, but will it matter to run it like this for the duration until I get it fully stable? Would this be ok?
Also, how can I fully reset a GPU to factory settings? Is there a way in bios or in smOS? If so please tell how?
Thank you so much for any help. It is very appreciated
|
|
|
Hello,
Does anyone have any good starting points for numbers on overclocking a 580 in simple mining OS (smOS)? 4gb version card. Also, if you have a crd you don't want to overclock, do you type 0 for the card?
For example: Memory MHz 1000, 1000, 0 .... or: Memory MHz 0, 1000, 1000
any help would be awesome!
Thank you so much.
|
|
|
Hello, So I am mining on dwarfpool, all seems to be going well now. It registers my worker/rig and I am getting shares. But when I try to add my IP address it does not let me reset my auto payout to lower amount. It says it is not the right IP adress. I am checking it on my laptop and noy my rig, as I am using SMos. Are they different IPs (the laptop and rig)? May that be the issue? How do I check IP using SMos if that is the case? Please help, it would be massivly appreciated
|
|
|
Also, as it seems you know about SMos, this would be correct assuming I set up account eth wallet and it register my worker rig right?
-wd 1 -r 1 -epool stratum+tcp://eth-eu.dwarfpool.com:8008 -ewal $walletETH/$rigName -esm 0 -epsw x -allpools 1 -mport -3333 -asm 1
The $walletETH/$rigName are auto-filled, right? Everything I read on the site and have seen on Vosk leads me to believe this is correct. It auto fills in your into.
Just wanted to verify.
Thank you so much
|
|
|
I did use wallet address. Or SMos does when you use the variable entry $rigName or the wallet variable. I am very sorry, what would be the right section? It is about eth so I used altcoin. My apologies.
|
|
|
Hello all,
Running single test gpu on SimpleMining OS. I am mining on Ethermine on SimpleMining OS. On SMos it says that I am getting shares and that my hashrate is ok, but when I try to confirm that I am mining on Ethermine, it says that it doess not find my adress. Which it should as long as SimpleMinining is working correctly and mining.
Here is my config: -wd 1 -r 1 -epool stratum+tcp://us1.ethermine.org:4444 -ewal ((wallet)) -esm 0 -epsw x -allpools 1 -mport -3333 -asm 1
ETH: GPU0 10.673 Mh/s DevFee: ETH: 12/13/17-06:45:43 - New job from us1.ethpool.org:3333 ETH: 12/13/17-06:45:44 - New job from us1.ethermine.org:4444 ETH - Total Speed: 10.670 Mh/s, Total Shares: 2, Rejected: 0, Time: 00:16 ETH: GPU0 10.670 Mh/s DevFee: ETH: 12/13/17-06:45:46 - New job from us1.ethpool.org:3333 GPU0 t=56C fan=27% DevFee: stop mining and disconnect ETH: 12/13/17-06:45:58 - New job from us1.ethermine.org:4444 ETH - Total Speed: 10.666 Mh/s, Total Shares: 2, Rejected: 0, Time: 00:17 ETH: GPU0 10.666 Mh/s ETH: 12/13/17-06:46:08 - New job from us1.ethermine.org:4444 ETH - Total Speed: 10.672 Mh/s, Total Shares: 2, Rejected: 0, Time: 00:17 ETH: GPU0 10.672 Mh/s
Also, what is with the DevFee: stop mining and disconnect bit?
Any help would be amazing.
|
|
|
ah i see thank you all. It won't affect mining speeds and hash rates for now though correct? Or at least not majorly so, right?
|
|
|
Hello all, I am still a bit fuzzy and really need some clarification. Can I boot OS from a jump drive, then install it to an external USB 1TB hard drive and run the OS off of the external hard drive, just for a month or two? Would it still function properly and mine the exact same? I have plenty of external hard drives and jump drives, just no standard HDD or SDD. If I am correct this will be fine, just a bit hard on the hard drive, but shouldn't affect any speeds or hash rates, right? If you could please help I would be very grateful ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
|
|
external HDD would work much smoother than jump drive I am guessing? Again this is just for a month or two, not permanent. Not ideal but it should all work fine, right?
thank you so much!!
|
|
|
I have a 1 TB external hard drive that plugs in via USB. Could I download Linux on the 1 TB portable hard drive and use it like that? Have plenty of USB sticks and external hard drives. Just no like SATA HHDs. Would that work just for a month or two period?? Thanks again all!! ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
|
|
Think Vosk Coin ordered a machine from them he said in a video, they seem legit. Don't just take my word tho lol ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
|
|
any thoughts? This is hopefully the last piece in my rig puzzle lol. Thanks so much!! ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) Think it should work fine, just slow
|
|
|
Hello all, I am going to be running Ubuntu from a USB and will be running only a miner and setting up pool and such on my rig. Will something like this be sufficient?? I know it will be very sluggish, but it should be good enough to run the OS and download a simple mining program and I should be good to go correct? If not could someone please tell me what path I should take? I know Vosk does something like this with smOS. I want to do the same thing with Linux basically. something like this is what I mean: https://www.amazon.com/Ubuntu-Linux-16-04-Bootable-Flash/dp/B01MR5OTM0/ref=sr_1_4?ie=UTF8&qid=1512436512&sr=8-4&keywords=linux+usbI know you can write your own, too. Thanks so much all. you are all amazingly helpful
|
|
|
thank you all again!! I offically placed my order today! Super excited
|
|
|
|