Ben getirirken sorun yaşadım, aracı bir gönderici ile 1 adet antminer ve psu için anlaştım alibaba.com dan, büyük kargo firmaları (dhl, fedex, ups) ile gönderim istedim fakat hata etmişim direk gümrük kontrolüne girdi ve takıldı, gönderi masrafı 820TL ve gümrük işlemleri aracı bir gümrük müşavirlik bürosu ile 1100 TL tuttu. Bilginiz olsun.

Tavsiyem tek ürün için anlaşın (2 ürüniçin anlaşmanız ticaretini yaptınığınız anlamına gelir ve yine takılır) hiç bir şekilde şirket adresine ve şirket ünvanı ile göndermeyin, kendi adınıza olması ve ev adresi olmasına dikkat edin, china post veya ems kargolarını tercih edin.

Merhaba,

Ülkemizde halen yedek parça ve tamir zorluğu yaşanmaktadır. Ömrü olan bu cihazlar için teknik destek şarttır.
Tamir yapan teknik servisler buradan kendilerini tanıtabilir, bilenler bilmeyenler için ekleme yapabilirler.

Ben Ankara da bir arkadaş ile görüştüm. Kendisinin bilgisini buradan paylaşıyorum. Teşekkürler

Caner Sayan
Cep 0 (544) 451 05 69

bitmain reply me

Thank you for contacting us. We are sorry for the delayed reply because our email volume has been extremely high.

Please try reloading the firmware:
D3:
https://shop.bitmain.com/support.htm?pid=00720170915192851224mJ36J1ap066E

Run the miner for 20 minutes after loading.

Please first check the PSU and the controller. To check the PSU you can test the machine with a known good PSU. If you do not have another PSU then check by switching the cables between hash boards. If the issue follows the cable then the PSU may be faulty. Please reply to this email for more instructions.

To test the controller, switch the controller cables between hash boards. If the same hash board shows the issue then the hash board is faulty. If the issue follows the cable then the controller may be faulty. Please contact us for further instructions.

If it still is not solved please test each hash board separately to determine which one is defective.

To test each hash board separately: keep the PSU connectors and controller cable on one of the hash boards connected and disconnect the cables from the other two hash boards. With the miner running you can see the status of the connected hash board.

Here is more detail: http://support.bitmain.com/hc/en-us/articles/226142788-Testing-hash-board-one-by-one

On the miner status screen defective chips are displayed as "xxx", "---" or " ASIC≠72

Once you know which part is defective please create a Repair ticket and ship the part back to us according to these instructions: https://shop.bitmain.com/workOrderGuide.htm
For D3, please measure your hashboard, kindly choose the right one based on the following size:
Hashboard D3(S) (222.6*156.7mm)
Hashboard D3(N) (222.6*176.6mm)

http://support.bitmain.com/hc/en-us/articles/222648028-How-to-disassemble-miners

Please pack the hash boards carefully. If the PINs are lost due to shipping damage it will void the warranty. Here is a video demonstrating how to pack the boards: https://youtu.be/Z0LdykALhxI

You may disassemble the miner and break the warranty seal under the instructions from this ticket.

Please let us know if you have additional questions or concerns.

Same problem.
I cant see chain no 3, working 19,5GH/s, its interesting. ( I think its nicehash hack effect )

Chain#    ASIC#    Frequency    GH/S(RT)    HW    Temp(PCB)    Temp(Chip)    ASIC status
                     
1   60   537   6409.59   2   54   76   oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooo
2   60   537   6455.22   0   52   74   oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooo