 Show Posts
|
|
Pages: [1]
|
1.SIR please do tell me which control board my miner is. i've attached the kernel logs and picture of control board clearly as i could not figure out. 2.also do tell me one thing do i need to just flash the 7007 or 7010 firmware you gave by going to upgrade and flash the image or i need to do something else? like with SD card which i'd never done before. AND BOARD 2 logs Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 199096K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 30280K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 17240K (cca2b000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2091/1513, WL threshold: 4096, image sequence number: 663922108
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FCC1D6E3-7267-4F09-B883-03EAD2BDC4DE, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 8/3, WL threshold: 4096, image sequence number: 750005443
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 1E4A66A7-7413-4113-8972-ED5E924CA43C, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab00d
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
main.c:13999: log_level = 4
main.c:14026: This is XILINX board. Totalram: 239353856
main.c:14044: Detect 256MB control board of XILINX
driver-bitmain.c:1777: mmap axi_fpga_addr = 0xb6f76000
driver-bitmain.c:1782: axi_fpga_addr data = 0xb00d
driver-bitmain.c:1798: mmap fpga_mem_addr = 0xb5d7a000
driver-bitmain.c:995: forceFreq=-1 forceFlag=0
driver-bitmain.c:1697: min work minertest[0]:912
main.c:8490: DETECT HW version=000ab00d
main.c:14071: miner ID : 8140742a79104814
main.c:14100: Miner Type = S9+
main.c:14108: AsicType = 1387
main.c:14111: real AsicNum = 84
main.c:14204: use critical mode to search freq...
driver-bitmain.c:1877: get PLUG ON=0x00000001
driver-bitmain.c:1947: Find hashboard on Chain[0]
main.c:2148: chain[0] PIC jump to app
main.c:2153: Check chain[0] PIC fw version=0xa4
main.c:8805: Chain[0] read_freq_badcores : 0x7d 0xd9 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0xd4 0x19 0x00 0x00 0xc8 0xff 0x3f 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0x39 0x0c 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8817: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[0] has freq in PIC and will jump over...
main.c:8999: Chain[0] has core num in PIC
main.c:9103: get PIC voltage=0 on chain[0], value=930
main.c:9269: chain[0] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9286: chain[0] temp chip I2C addr=0x98
main.c:13963: total_exist_chain_num = 1
main.c:14645: restart Miner chance num=0
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13934: bmminer not found= 1030 root 2156 S grep bmminer
main.c:14743: bmminer not found, restart bmminer ...
driver-btm-c5.c:12248:bitmain_c5_init: This is the first time running after searching freq!
driver-btm-c5.c:12308:bitmain_c5_init: Detect 256MB control board of XILINX
driver-btm-c5.c:12327:bitmain_c5_init: Miner Type = S9+
driver-btm-c5.c:12334:bitmain_c5_init: Miner compile time: Thu Aug 1 16:39:38 CST 2019 type: Antminer S11
driver-btm-c5.c:12424:bitmain_c5_init: miner ID : 8140742a79104814
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=3120
driver-btm-c5.c:12581:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=3120
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=3120
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=3120
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[0] PIC fw version=0xa4
driver-btm-c5.c:13034:bitmain_c5_init: Chain[0] read_freq_badcores : 0x7d 0xd9 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0xd4 0x19 0x00 0x00 0xc8 0xff 0x3f 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0x39 0x0c 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:13073:bitmain_c5_init: Chain[J1] has backup chain_voltage=1085
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.850000
driver-btm-c5.c:13084:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13088:bitmain_c5_init: S9+ fix Chain[J1] test patten OK temp=60
driver-btm-c5.c:12205:init_exist_chain_table: total_exist_chain_num = 1
power.c:148:power_check_protocal_type: power protocal f5, using package cmd
power.c:173:power_type_detect: start detect power type
power.c:181:power_type_detect: init gpio907
power.c:211:power_type_detect: power type is APW8 new type
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[0] voltage: 0.164355
power.c:593:get_min_voltage: min voltage: 0.164355
power.c:370:voltage_tunning: last_iic_data = 60
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=28
power.c:587:get_min_voltage: board[0] voltage: 0.164355
power.c:593:get_min_voltage: min voltage: 0.164355
power.c:370:voltage_tunning: last_iic_data = 28
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=0
power.c:565:get_avg_voltage: board[0] voltage: 0.164355
power.c:571:get_avg_voltage: avg voltage: 0.164355
driver-btm-c5.c:12210:stop_mining: power voltage too low
i even tried BOARD 2 on power saving mode Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 199096K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 30280K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 17240K (cca2b000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2091/1513, WL threshold: 4096, image sequence number: 663922108
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FCC1D6E3-7267-4F09-B883-03EAD2BDC4DE, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 8/3, WL threshold: 4096, image sequence number: 750005443
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 1E4A66A7-7413-4113-8972-ED5E924CA43C, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab00d
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
main.c:13999: log_level = 4
main.c:14026: This is XILINX board. Totalram: 239353856
main.c:14044: Detect 256MB control board of XILINX
driver-bitmain.c:1777: mmap axi_fpga_addr = 0xb6f28000
driver-bitmain.c:1782: axi_fpga_addr data = 0xb00d
driver-bitmain.c:1798: mmap fpga_mem_addr = 0xb5d2c000
driver-bitmain.c:995: forceFreq=-1 forceFlag=0
driver-bitmain.c:1697: min work minertest[0]:912
main.c:8490: DETECT HW version=000ab00d
main.c:14071: miner ID : 8140742a79104814
main.c:14100: Miner Type = S9+
main.c:14108: AsicType = 1387
main.c:14111: real AsicNum = 84
main.c:14204: use critical mode to search freq...
driver-bitmain.c:1877: get PLUG ON=0x00000001
driver-bitmain.c:1947: Find hashboard on Chain[0]
main.c:2148: chain[0] PIC jump to app
main.c:2153: Check chain[0] PIC fw version=0xa4
main.c:8805: Chain[0] read_freq_badcores : 0x7d 0xd9 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0xd4 0x19 0x00 0x00 0xc8 0xff 0x3f 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0x39 0x0c 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8817: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[0] has freq in PIC and will jump over...
main.c:8999: Chain[0] has core num in PIC
main.c:9103: get PIC voltage=0 on chain[0], value=930
main.c:9269: chain[0] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9286: chain[0] temp chip I2C addr=0x98
main.c:13963: total_exist_chain_num = 1
main.c:14645: restart Miner chance num=2
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13934: bmminer not found= 1390 root 2156 S grep bmminer
main.c:14743: bmminer not found, restart bmminer ...
driver-btm-c5.c:12253:bitmain_c5_init: This is user mode for mining
driver-btm-c5.c:12308:bitmain_c5_init: Detect 256MB control board of XILINX
driver-btm-c5.c:12327:bitmain_c5_init: Miner Type = S9+
driver-btm-c5.c:12334:bitmain_c5_init: Miner compile time: Thu Aug 1 16:39:38 CST 2019 type: Antminer S11
driver-btm-c5.c:12424:bitmain_c5_init: miner ID : 8140742a79104814
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:12581:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[0] PIC fw version=0xa4
driver-btm-c5.c:13034:bitmain_c5_init: Chain[0] read_freq_badcores : 0x7d 0xd9 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0xd4 0x19 0x00 0x00 0xc8 0xff 0x3f 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0x39 0x0c 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:13043:bitmain_c5_init: S11 USE LOW POWER MODE!
driver-btm-c5.c:13073:bitmain_c5_init: Chain[J1] has backup chain_voltage=1000
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.180000
driver-btm-c5.c:13084:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13088:bitmain_c5_init: S9+ fix Chain[J1] test patten OK temp=60
driver-btm-c5.c:12205:init_exist_chain_table: total_exist_chain_num = 1
power.c:148:power_check_protocal_type: power protocal f5, using package cmd
power.c:173:power_type_detect: start detect power type
power.c:211:power_type_detect: power type is APW8 new type
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[0] voltage: 0.209473
power.c:593:get_min_voltage: min voltage: 0.209473
power.c:370:voltage_tunning: last_iic_data = 176
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=144
power.c:587:get_min_voltage: board[0] voltage: 0.209473
power.c:593:get_min_voltage: min voltage: 0.209473
power.c:370:voltage_tunning: last_iic_data = 144
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=112
power.c:587:get_min_voltage: board[0] voltage: 0.209473
power.c:593:get_min_voltage: min voltage: 0.209473
power.c:370:voltage_tunning: last_iic_data = 112
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=80
power.c:587:get_min_voltage: board[0] voltage: 0.209473
power.c:593:get_min_voltage: min voltage: 0.209473
power.c:370:voltage_tunning: last_iic_data = 80
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=48
power.c:587:get_min_voltage: board[0] voltage: 0.209473
power.c:593:get_min_voltage: min voltage: 0.209473
power.c:370:voltage_tunning: last_iic_data = 48
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=16
power.c:587:get_min_voltage: board[0] voltage: 0.209473
power.c:593:get_min_voltage: min voltage: 0.209473
power.c:370:voltage_tunning: last_iic_data = 16
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=0
power.c:565:get_avg_voltage: board[0] voltage: 0.209473
power.c:571:get_avg_voltage: avg voltage: 0.209473
driver-btm-c5.c:12210:stop_mining: power voltage too low
|
|
|
|
Hello sir im attaching the picture should i just remove those two ribbon cables and keep one cable attached and just power it on low power saving mode? https://imgur.com/a/NBuean2 |
|
|
|
sometimes the Third chip starts showing and sometimes first and second power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.212695
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:629:set_iic_power_voltage: power voltage abnormal
driver-btm-c5.c:12210:stop_mining: power abnormal
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.009668
power.c:587:get_min_voltage: board[0] voltage: 0.203027
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:629:set_iic_power_voltage: power voltage abnormal
driver-btm-c5.c:12210:stop_mining: power abnormal
Sir after i'd upgraded it to the latest firmfare just from that period of time after 5-7 days it has gone bad. i tried to upgrade back but it says cannot find signature. so my question is will it help if i degrade the existing firmware by using some method to degrade it? If my Antminer s11's APW8 psu has gone wrong can i use antminer s9 psu in it? i've got one extra to make things work. |
|
|
|
|
I'm really very sorry i'll be taking care of posting in the right way from next time. its 220v i'm using 1 phase in india out of 3 phase house.
How to do it like this
1-remove board 1 and 2 keep board 3
2-remove board 1 and 3 keep board 2
3-remove board 2 and 3 keep board 1
In S11 by apw8 power supply i've never done before i need proper guidance. i've tried doing in antminer s9 before but this one is having connected power supply and there are less wires.
|
|
|
|
And YESTERDAY IT WAS LIKE THIS WAS IT NORMAL? i'd saved the kernal logs of yesterday And thankyou for helping me out in this ! power.c:587:get_min_voltage: board[1] voltage: 0.215918
power.c:587:get_min_voltage: board[2] voltage: 0.141797
power.c:587:get_min_voltage: board[0] voltage: 0.019336
power.c:593:get_min_voltage: min voltage: 0.019336
power.c:370:voltage_tunning: last_iic_data = 166
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=164
power.c:587:get_min_voltage: board[1] voltage: 0.215918
power.c:587:get_min_voltage: board[2] voltage: 0.141797
power.c:587:get_min_voltage: board[0] voltage: 0.196582
power.c:593:get_min_voltage: min voltage: 0.141797
power.c:370:voltage_tunning: last_iic_data = 164
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=162
power.c:587:get_min_voltage: board[1] voltage: 0.215918
power.c:587:get_min_voltage: board[2] voltage: 0.141797
power.c:587:get_min_voltage: board[0] voltage: 0.196582
power.c:593:get_min_voltage: min voltage: 0.141797
power.c:370:voltage_tunning: last_iic_data = 162
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=160
power.c:587:get_min_voltage: board[1] voltage: 0.215918
power.c:587:get_min_voltage: board[2] voltage: 0.141797
power.c:587:get_min_voltage: board[0] voltage: 0.196582
power.c:593:get_min_voltage: min voltage: 0.141797
power.c:370:voltage_tunning: last_iic_data = 160
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=158
power.c:587:get_min_voltage: board[1] voltage: 0.215918
power.c:587:get_min_voltage: board[2] voltage: 0.141797
power.c:587:get_min_voltage: board[0] voltage: 0.196582
power.c:593:get_min_voltage: min voltage: 0.141797
power.c:370:voltage_tunning: last_iic_data = 158
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=156
power.c:629:set_iic_power_voltage: power voltage abnormal
driver-btm-c5.c:12210:stop_mining: power abnormal
|
|
|
|
i've turned off low powe saving mode and in low power saving sometimes the third hashboard shows some respose and values Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 199096K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 30280K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 17240K (cca2b000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2091/1512, WL threshold: 4096, image sequence number: 663922108
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FCC1D6E3-7267-4F09-B883-03EAD2BDC4DE, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 8/3, WL threshold: 4096, image sequence number: 750005443
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 1E4A66A7-7413-4113-8972-ED5E924CA43C, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab00d
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
main.c:13999: log_level = 4
main.c:14026: This is XILINX board. Totalram: 239353856
main.c:14044: Detect 256MB control board of XILINX
driver-bitmain.c:1777: mmap axi_fpga_addr = 0xb6ff1000
driver-bitmain.c:1782: axi_fpga_addr data = 0xb00d
driver-bitmain.c:1798: mmap fpga_mem_addr = 0xb5df5000
driver-bitmain.c:995: forceFreq=-1 forceFlag=0
driver-bitmain.c:1697: min work minertest[0]:912
main.c:8490: DETECT HW version=000ab00d
main.c:14071: miner ID : 8140742a79104814
main.c:14100: Miner Type = S9+
main.c:14108: AsicType = 1387
main.c:14111: real AsicNum = 84
main.c:14204: use critical mode to search freq...
driver-bitmain.c:1877: get PLUG ON=0x00000007
driver-bitmain.c:1947: Find hashboard on Chain[0]
driver-bitmain.c:1947: Find hashboard on Chain[1]
driver-bitmain.c:1947: Find hashboard on Chain[2]
main.c:2148: chain[0] PIC jump to app
main.c:2153: Check chain[0] PIC fw version=0xa4
main.c:2148: chain[1] PIC jump to app
main.c:2153: Check chain[1] PIC fw version=0xa4
main.c:2148: chain[2] PIC jump to app
main.c:2153: Check chain[2] PIC fw version=0xa4
main.c:8805: Chain[0] read_freq_badcores : 0x7d 0xd9 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0xd4 0x19 0x00 0x00 0xc8 0xff 0x3f 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0x39 0x0c 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8817: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[0] has freq in PIC and will jump over...
main.c:8999: Chain[0] has core num in PIC
main.c:8805: Chain[1] read_freq_badcores : 0x7d 0xd9 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x0b 0x1a 0x00 0x00 0xc8 0xbe 0xff 0xfa 0xfe 0xbe 0xef 0xbe 0xef 0xfb 0xfb 0xbb 0xfb 0xfb 0xeb 0xef 0xbb 0xef 0xbf 0xfe 0xee 0xfb 0x67 0x13 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8817: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[1] has freq in PIC and will jump over...
main.c:8999: Chain[1] has core num in PIC
main.c:8805: Chain[2] read_freq_badcores : 0x7d 0xd9 0x56 0x4e 0x52 0x52 0x56 0x4e 0x52 0x56 0x4e 0x4e 0x52 0x56 0x56 0x52 0x4e 0x52 0x56 0x4e 0x56 0x52 0x4e 0x56 0x52 0x4e 0x4e 0x52 0x56 0x4e 0x56 0x52 0x56 0x4e 0x52 0x52 0x4e 0x56 0x52 0x56 0x4e 0x52 0x4e 0x56 0x52 0x56 0x4e 0x56 0x52 0x4e 0x56 0x4e 0x52 0x4e 0x56 0x52 0x52 0x4e 0x56 0x4e 0x56 0x52 0x56 0x52 0x4e 0x56 0x52 0x4e 0x4e 0x52 0x56 0x4e 0x52 0x56 0x56 0x4e 0x52 0x4e 0x56 0x52 0x4e 0x56 0x52 0x52 0x4e 0x56 0xc1 0x19 0x00 0x00 0xc8 0xfd 0x7d 0x7f 0xfd 0xdd 0xf7 0xdf 0xdd 0x7f 0xf7 0x77 0xf7 0xfd 0xf7 0xdd 0xfd 0x7d 0x7f 0xdf 0x7d 0x7f 0x04 0x12 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8817: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[2] has freq in PIC and will jump over...
main.c:8999: Chain[2] has core num in PIC
main.c:9103: get PIC voltage=0 on chain[0], value=930
main.c:9103: get PIC voltage=0 on chain[1], value=930
main.c:9103: get PIC voltage=0 on chain[2], value=930
main.c:9269: chain[0] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9286: chain[0] temp chip I2C addr=0x98
main.c:9269: chain[1] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9286: chain[1] temp chip I2C addr=0x98
main.c:9269: chain[2] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9286: chain[2] temp chip I2C addr=0x98
main.c:13963: total_exist_chain_num = 3
main.c:14645: restart Miner chance num=2
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13934: bmminer not found= 1999 root 2156 S grep bmminer
main.c:14743: bmminer not found, restart bmminer ...
driver-btm-c5.c:12253:bitmain_c5_init: This is user mode for mining
driver-btm-c5.c:12308:bitmain_c5_init: Detect 256MB control board of XILINX
driver-btm-c5.c:12327:bitmain_c5_init: Miner Type = S9+
driver-btm-c5.c:12334:bitmain_c5_init: Miner compile time: Thu Aug 1 16:39:38 CST 2019 type: Antminer S11
driver-btm-c5.c:12424:bitmain_c5_init: miner ID : 8140742a79104814
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=2640
driver-btm-c5.c:12581:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[0] PIC fw version=0xa4
driver-btm-c5.c:13034:bitmain_c5_init: Chain[0] read_freq_badcores : 0x7d 0xd9 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0xd4 0x19 0x00 0x00 0xc8 0xff 0x3f 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0x39 0x0c 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:13073:bitmain_c5_init: Chain[J1] has backup chain_voltage=1085
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.850000
driver-btm-c5.c:13084:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13088:bitmain_c5_init: S9+ fix Chain[J1] test patten OK temp=60
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[1] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[1] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[1] PIC fw version=0xa4
driver-btm-c5.c:13034:bitmain_c5_init: Chain[1] read_freq_badcores : 0x7d 0xd9 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x0b 0x1a 0x00 0x00 0xc8 0xbe 0xff 0xfa 0xfe 0xbe 0xef 0xbe 0xef 0xfb 0xfb 0xbb 0xfb 0xfb 0xeb 0xef 0xbb 0xef 0xbf 0xfe 0xee 0xfb 0x67 0x13 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:13073:bitmain_c5_init: Chain[J2] has backup chain_voltage=1085
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.850000
driver-btm-c5.c:13084:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13088:bitmain_c5_init: S9+ fix Chain[J2] test patten OK temp=60
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[2] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[2] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[2] PIC fw version=0xa4
driver-btm-c5.c:13034:bitmain_c5_init: Chain[2] read_freq_badcores : 0x7d 0xd9 0x56 0x4e 0x52 0x52 0x56 0x4e 0x52 0x56 0x4e 0x4e 0x52 0x56 0x56 0x52 0x4e 0x52 0x56 0x4e 0x56 0x52 0x4e 0x56 0x52 0x4e 0x4e 0x52 0x56 0x4e 0x56 0x52 0x56 0x4e 0x52 0x52 0x4e 0x56 0x52 0x56 0x4e 0x52 0x4e 0x56 0x52 0x56 0x4e 0x56 0x52 0x4e 0x56 0x4e 0x52 0x4e 0x56 0x52 0x52 0x4e 0x56 0x4e 0x56 0x52 0x56 0x52 0x4e 0x56 0x52 0x4e 0x4e 0x52 0x56 0x4e 0x52 0x56 0x56 0x4e 0x52 0x4e 0x56 0x52 0x4e 0x56 0x52 0x52 0x4e 0x56 0xc1 0x19 0x00 0x00 0xc8 0xfd 0x7d 0x7f 0xfd 0xdd 0xf7 0xdf 0xdd 0x7f 0xf7 0x77 0xf7 0xfd 0xf7 0xdd 0xfd 0x7d 0x7f 0xdf 0x7d 0x7f 0x04 0x12 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:13073:bitmain_c5_init: Chain[J3] has backup chain_voltage=1085
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.850000
driver-btm-c5.c:13084:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13088:bitmain_c5_init: S9+ fix Chain[J3] test patten OK temp=60
driver-btm-c5.c:12205:init_exist_chain_table: total_exist_chain_num = 3
power.c:148:power_check_protocal_type: power protocal f5, using package cmd
power.c:173:power_type_detect: start detect power type
power.c:211:power_type_detect: power type is APW8 new type
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.009668
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.009668
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.009668
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.009668
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.009668
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.009668
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.009668
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:629:set_iic_power_voltage: power voltage abnormal
driver-btm-c5.c:12210:stop_mining: power abnormal
NOW IT SAYS THIS and also i placed ur given address in pool 2. |
|
|
|
antminer s11 not working the kernel log is as follows : Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 199096K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 30280K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 17240K (cca2b000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2091/1512, WL threshold: 4096, image sequence number: 663922108
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FCC1D6E3-7267-4F09-B883-03EAD2BDC4DE, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 8/3, WL threshold: 4096, image sequence number: 750005443
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 1E4A66A7-7413-4113-8972-ED5E924CA43C, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab00d
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
main.c:13999: log_level = 4
main.c:14026: This is XILINX board. Totalram: 239353856
main.c:14044: Detect 256MB control board of XILINX
driver-bitmain.c:1777: mmap axi_fpga_addr = 0xb6fb8000
driver-bitmain.c:1782: axi_fpga_addr data = 0xb00d
driver-bitmain.c:1798: mmap fpga_mem_addr = 0xb5dbc000
driver-bitmain.c:995: forceFreq=-1 forceFlag=0
driver-bitmain.c:1697: min work minertest[0]:912
main.c:8490: DETECT HW version=000ab00d
main.c:14071: miner ID : 8140742a79104814
main.c:14100: Miner Type = S9+
main.c:14108: AsicType = 1387
main.c:14111: real AsicNum = 84
main.c:14204: use critical mode to search freq...
driver-bitmain.c:1877: get PLUG ON=0x00000007
driver-bitmain.c:1947: Find hashboard on Chain[0]
driver-bitmain.c:1947: Find hashboard on Chain[1]
driver-bitmain.c:1947: Find hashboard on Chain[2]
main.c:2148: chain[0] PIC jump to app
main.c:2153: Check chain[0] PIC fw version=0xa4
main.c:2148: chain[1] PIC jump to app
main.c:2153: Check chain[1] PIC fw version=0xa4
main.c:2148: chain[2] PIC jump to app
main.c:2153: Check chain[2] PIC fw version=0xa4
main.c:8805: Chain[0] read_freq_badcores : 0x7d 0xd9 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0xd4 0x19 0x00 0x00 0xc8 0xff 0x3f 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0x39 0x0c 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8817: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[0] has freq in PIC and will jump over...
main.c:8999: Chain[0] has core num in PIC
main.c:8805: Chain[1] read_freq_badcores : 0x7d 0xd9 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x0b 0x1a 0x00 0x00 0xc8 0xbe 0xff 0xfa 0xfe 0xbe 0xef 0xbe 0xef 0xfb 0xfb 0xbb 0xfb 0xfb 0xeb 0xef 0xbb 0xef 0xbf 0xfe 0xee 0xfb 0x67 0x13 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8817: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[1] has freq in PIC and will jump over...
main.c:8999: Chain[1] has core num in PIC
main.c:8805: Chain[2] read_freq_badcores : 0x7d 0xd9 0x56 0x4e 0x52 0x52 0x56 0x4e 0x52 0x56 0x4e 0x4e 0x52 0x56 0x56 0x52 0x4e 0x52 0x56 0x4e 0x56 0x52 0x4e 0x56 0x52 0x4e 0x4e 0x52 0x56 0x4e 0x56 0x52 0x56 0x4e 0x52 0x52 0x4e 0x56 0x52 0x56 0x4e 0x52 0x4e 0x56 0x52 0x56 0x4e 0x56 0x52 0x4e 0x56 0x4e 0x52 0x4e 0x56 0x52 0x52 0x4e 0x56 0x4e 0x56 0x52 0x56 0x52 0x4e 0x56 0x52 0x4e 0x4e 0x52 0x56 0x4e 0x52 0x56 0x56 0x4e 0x52 0x4e 0x56 0x52 0x4e 0x56 0x52 0x52 0x4e 0x56 0xc1 0x19 0x00 0x00 0xc8 0xfd 0x7d 0x7f 0xfd 0xdd 0xf7 0xdf 0xdd 0x7f 0xf7 0x77 0xf7 0xfd 0xf7 0xdd 0xfd 0x7d 0x7f 0xdf 0x7d 0x7f 0x04 0x12 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8817: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[2] has freq in PIC and will jump over...
main.c:8999: Chain[2] has core num in PIC
main.c:9103: get PIC voltage=0 on chain[0], value=930
main.c:9103: get PIC voltage=0 on chain[1], value=930
main.c:9103: get PIC voltage=0 on chain[2], value=930
main.c:9269: chain[0] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9286: chain[0] temp chip I2C addr=0x98
main.c:9269: chain[1] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9286: chain[1] temp chip I2C addr=0x98
main.c:9269: chain[2] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9286: chain[2] temp chip I2C addr=0x98
main.c:13963: total_exist_chain_num = 3
main.c:14645: restart Miner chance num=0
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13934: bmminer not found= 1031 root 2156 S grep bmminer
main.c:14743: bmminer not found, restart bmminer ...
driver-btm-c5.c:12248:bitmain_c5_init: This is the first time running after searching freq!
driver-btm-c5.c:12308:bitmain_c5_init: Detect 256MB control board of XILINX
driver-btm-c5.c:12327:bitmain_c5_init: Miner Type = S9+
driver-btm-c5.c:12334:bitmain_c5_init: Miner compile time: Thu Aug 1 16:39:38 CST 2019 type: Antminer S11
driver-btm-c5.c:12424:bitmain_c5_init: miner ID : 8140742a79104814
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=1800
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=1800
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=1800
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:12581:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[0] PIC fw version=0xa4
driver-btm-c5.c:13034:bitmain_c5_init: Chain[0] read_freq_badcores : 0x7d 0xd9 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0xd4 0x19 0x00 0x00 0xc8 0xff 0x3f 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0x39 0x0c 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:13043:bitmain_c5_init: S11 USE LOW POWER MODE!
driver-btm-c5.c:13073:bitmain_c5_init: Chain[J1] has backup chain_voltage=1000
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.180000
driver-btm-c5.c:13084:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13088:bitmain_c5_init: S9+ fix Chain[J1] test patten OK temp=60
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[1] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[1] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[1] PIC fw version=0xa4
driver-btm-c5.c:13034:bitmain_c5_init: Chain[1] read_freq_badcores : 0x7d 0xd9 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x0b 0x1a 0x00 0x00 0xc8 0xbe 0xff 0xfa 0xfe 0xbe 0xef 0xbe 0xef 0xfb 0xfb 0xbb 0xfb 0xfb 0xeb 0xef 0xbb 0xef 0xbf 0xfe 0xee 0xfb 0x67 0x13 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:13043:bitmain_c5_init: S11 USE LOW POWER MODE!
driver-btm-c5.c:13073:bitmain_c5_init: Chain[J2] has backup chain_voltage=1000
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.180000
driver-btm-c5.c:13084:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13088:bitmain_c5_init: S9+ fix Chain[J2] test patten OK temp=60
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[2] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[2] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[2] PIC fw version=0xa4
driver-btm-c5.c:13034:bitmain_c5_init: Chain[2] read_freq_badcores : 0x7d 0xd9 0x56 0x4e 0x52 0x52 0x56 0x4e 0x52 0x56 0x4e 0x4e 0x52 0x56 0x56 0x52 0x4e 0x52 0x56 0x4e 0x56 0x52 0x4e 0x56 0x52 0x4e 0x4e 0x52 0x56 0x4e 0x56 0x52 0x56 0x4e 0x52 0x52 0x4e 0x56 0x52 0x56 0x4e 0x52 0x4e 0x56 0x52 0x56 0x4e 0x56 0x52 0x4e 0x56 0x4e 0x52 0x4e 0x56 0x52 0x52 0x4e 0x56 0x4e 0x56 0x52 0x56 0x52 0x4e 0x56 0x52 0x4e 0x4e 0x52 0x56 0x4e 0x52 0x56 0x56 0x4e 0x52 0x4e 0x56 0x52 0x4e 0x56 0x52 0x52 0x4e 0x56 0xc1 0x19 0x00 0x00 0xc8 0xfd 0x7d 0x7f 0xfd 0xdd 0xf7 0xdf 0xdd 0x7f 0xf7 0x77 0xf7 0xfd 0xf7 0xdd 0xfd 0x7d 0x7f 0xdf 0x7d 0x7f 0x04 0x12 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:13043:bitmain_c5_init: S11 USE LOW POWER MODE!
driver-btm-c5.c:13073:bitmain_c5_init: Chain[J3] has backup chain_voltage=1000
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.180000
driver-btm-c5.c:13084:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13088:bitmain_c5_init: S9+ fix Chain[J3] test patten OK temp=60
driver-btm-c5.c:12205:init_exist_chain_table: total_exist_chain_num = 3
power.c:148:power_check_protocal_type: power protocal f5, using package cmd
power.c:173:power_type_detect: start detect power type
power.c:181:power_type_detect: init gpio907
power.c:211:power_type_detect: power type is APW8 new type
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[176] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.180000, N=176
power.c:629:set_iic_power_voltage: power voltage abnormal
driver-btm-c5.c:12210:stop_mining: power abnormal
|
|
|
|
|
some people say that it's going to soft fork and a3's are going to be dead. is it true or should we buy this antminer?
|
|
|
|
|
i want to transfer my bitcoin cash from bitfinex to bittrex
In bitfinex the symbol is BCH and in bittrex its BCC.
|
|
|
|
|
And what the temperature should be between?
|
|
|
|
|
I’ve just bought a bitmain antminer s9 and how can i check the temperature of this machine?
|
|
|
|
|
does it mines all SHA 256 currencies or just mines bitcoin?
i'm close to purchase one tomorrow.
|
|
|
|
|
