Latest posts of: PiTimes

Show Posts
Pages: [1]

Bitcoin / Hardware / Re: GekkoScience has a new stickminer that does 300+GH

on: February 12, 2022, 06:40:34 PM

I was afraid of that... thanks Sidehack

Bitcoin / Hardware / Re: GekkoScience has a new stickminer that does 300+GH

on: February 12, 2022, 03:42:05 PM

Quote from: itskeule on February 12, 2022, 02:28:40 PM

Quote from: PiTimes on February 12, 2022, 01:58:09 PM

Any one have some advice here? I am running out of ideas, rest of my Compac Fs run fine, this one did for a while too, now all of a sudden:

Code:

 0: GSF 10050600: found 0 chip(s)         |  0.000 /  0.000h/s WU:0.0/m

Cgminer keeps trying to start it:

Code:

 2: GSF 10050600: found 0 chip(s)         | OFF

Not sure where to go next, played with freq & voltage... reinstalled driver... Thanks in advance of any advice.

Change the USB hub and the PSU.

I got 5 others running on the same USB Hub... PSU is built in, it's the 20 port one. I've unplugged them all to test this one, tried hot plugging etc...

Code:

--------------------------------------------------------------------------------                                         
[U]SB management [P]ool management [S]ettings [D]isplay options [Q]uit                                                
 1: GSF 10050675: BM1397:01+ 450.00MHz T:450 P:449 (28:14)  |  100% WU:100% | 334.9G / 255.3Gh/s WU:3566.2/m       
 2: GSF 10050690: BM1397:01+ 450.00MHz T:450 P:449 (28:14)  |  100% WU:100% | 303.3G / 238.6Gh/s WU:3346.8/m           
 3: GSF 10050691: BM1397:01+ 450.00MHz T:450 P:446 (28:14)  |  100% WU:100% | 372.5G / 252.3Gh/s WU:3531.9/m            
 4: GSF 10050692: BM1397:01+ 450.00MHz T:450 P:445 (28:14)  |  100% WU:100% | 328.1G / 252.8Gh/s WU:3531.9/m            
 5: GSF 10050420: BM1397:01+ 450.00MHz T:450 P:450 (28:14)  |  100% WU:^98% | 297.0G / 232.4Gh/s WU:3246.0/m           
 --------------------------------------------------------------------------------

Bitcoin / Hardware / Re: GekkoScience has a new stickminer that does 300+GH

on: February 12, 2022, 01:58:09 PM

Any one have some advice here? I am running out of ideas, rest of my Compac Fs run fine, this one did for a while too, now all of a sudden: Code: 0: GSF 10050600: found 0 chip(s) \| 0.000 / 0.000h/s WU:0.0/m Cgminer keeps trying to start it: Code: 2: GSF 10050600: found 0 chip(s) \| OFF Not sure where to go next, played with freq & voltage... reinstalled driver... Thanks in advance of any advice.

Bitcoin / Hardware / Re: GekkoScience has a new stickminer that does 300+GH

on: February 03, 2022, 02:32:32 AM

I am using a 110V 20 port USB: https://www.eyeboot.com/sipolar-20-port-usb3.html Current shouldn't be an issue... unless it is. But I am still able to run 8 2pacs at 250mhz... I am at a loss. I don't have a USB multimeter, but they look cheap I will probably invest in one. I have toggled with the voltage on the stick and the freq in cgminer. Tried jump starting at 500mhz, no dice for the 0 chip, and the other one I could hear audibly beeping, softly and rapidly.

Bitcoin / Hardware / Re: GekkoScience has a new stickminer that does 300+GH

on: February 02, 2022, 11:54:59 PM

Hey all, looking for a little direction here... Had my Fs running like champs for one day, barely 24hrs. Now they look like this:

Code:

--------------------------------------------------------------------------------  
           [U]SB management [P]ool management [S]ettings [D]isplay options [Q]uit                                                  
0: GSF 10050420: BM1397:01+ 95.00MHz T:95  P:32  (135:67) | 31.3% WU: 16% | 16.53G / 7.718Gh/s WU:107.8/m              
 3: GSF 10050600: found 0 chip(s)                                          | OFF                                      
  --------------------------------------------------------------------------------

Here is .bat configuration:

Code:

cgminer.exe -o stratum+tcp://us-east.stratum.slushpool.com:3333 -u X -p Y --gekko-compacf-detect --gekko-compacf-freq 400 --gekko-start-freq 200 --gekko-mine2 --gekko-tune-up 85

I play with the start freq a bit, going below default thinking maybe that would find this chip... but the other one is throttled like crazy. I have plenty of active cooling, so tell me I didn't fry them. Meanwhile I got 4 to 8 2pacs running @ 250mhz for a couple years now.

Thanks,

Bitcoin / Mining software (miners) / Re: OFFICIAL CGMINER mining software thread for linux/win/osx/mips/arm/r-pi 4.10.0

on: December 30, 2017, 12:16:24 AM

You sir are a gentleman and a scholar. Worked like a charm, helps when you have the correct command, and put it in the right place. Thank you

Bitcoin / Mining software (miners) / Re: OFFICIAL CGMINER mining software thread for linux/win/osx/mips/arm/r-pi 4.10.0

on: December 29, 2017, 04:09:45 PM

Hey all, I am dusting off my old rpi and gekko 2pacs to get back into mining. want to get more familiar with everything again before investing big bucks back into an S9 or two. So they are currently running fine on Cgminer, about 11-12 Gh/s each. My question is, and I flipped though a lot of these posts to find my answer and could not, how can I overclock these puppies? I saw the cd in the read me file, and on the 1st sticky here: --compac-freq <arg> Set GekkoScience Compac frequency in MHz, range 100-500 (default: 150.0) so in cgminer Settings and enter cgminer.config then I enter --compac-freq <200> entry not recognized sorry not at my Pi so this is the best i could remember. any help is appreciated.

Pages: [1]