 Show Posts
|
|
Pages: [1] 2 »
|
Hello Renatopinto, Sorry for delay. This is classic TTL cable: https://www.ebay.fr/itm/400708482567Plug TTL Cable on your PC and lets windows install driver. Go in Windows bar and in "Device Manager" and in "PORT & COM" you will see your cable and his PORT attributed. After that you need to have software to manage result of signal (on terminal), for exemple on Windows you have: MobaXterm Launch MobaXTerm -> Session -> Select Serial ->Select right COM port -> Speed 15600 bps and RUN Plug your TTL cable on controal board (TX, GND, RX) and turn on the board. and all result will appear on your screen ! Best regards |
|
|
|
Hello everyone, So I received the PHY chips, and I can confirm....that it came from there. So in conclusion, if you have the DDR blinks which are faintly lit and the ETH socket blinks off and in your logs via TTL cable you have code similar to mine up to "eth%d: No PHY found". there's a good chance that the PHY part is responsible for the control board not booting. Because it's one of the last parts to boot (after the CPU in any case). The following diagram gave me a clue, as it clearly shows that the PHY module controls the ETHERNET, the LEDS and the magnetic. I hope this has helped some people! (but I curse AMLOGIC anyway, it's poorly documented and fragile as hell).     |
|
|
|
|
You bought a second-hand miner and the logs show that the hashboards are correct, no CRC counter, you can connect to the interface locally, so it's OK. So I'd say virus.
As the person above me said, take a custom firmware with on-board antivirus and try flashing it.
|
|
|
|
|
All right! I ordered a set of PHY chip, it will arrive in 15 days.
See you
|
|
|
|
After careful analysis, the last line corresponds to "No Phy Found". The rest of the logs show a healthy boot and NAND. So I started looking at the PHY chip. On the internet you can find this diagram:  I conclude that since my leds and eth plug are off and PHY is controlling this, the little PHY chip is dead. So I unsoldered the part and ran the analysis, and the logs are exactly the same, confirming my point. I'll order the part and keep you posted. |
|
|
|
Hello, I went straight to the TTL step because all the previous steps (the IpReport button, the flash with microUSB with the little green light that comes on after 30sec) had already been done but the restart doesn't happen. So I decided to use mobaxterm and a TTL cable to check what was happening in the control board, and I've posted the results above. I've also attached below the TTL log during boot with the microUSB for firmware. AXG:BL1:d1dbf2:a4926f;FEAT:F0DC31BC:2000;POC:F;EMMC:800;NAND:0;READ:0;0.0;0.0;CHK:0;
sdio debug board detected
TE: 136410
BL2 Built : 10:38:43, Apr 14 2020. axg gf27ed33 - jenkins@walle02-sh
set vcck to 1100 mv
set vddee to 950 mv
init panel power
Board ID = 0
CPU clk: 1200MHz
DDR low power enabled
DDR3 chl: Rank0 16bit @ 912MHz
bist_test rank: 0 17 00 2f 2a 11 44 1b 00 37 26 0c 41 00 00 00 00 00 00 00 00 00 00 00 00 721 - PASS
Rank0: 256MB-2T-13
AddrBus test pass!
NAND init
Load FIP HDR from NAND, src: 0x0000c000, des: 0x01700000, size: 0x00004000, part: 0
Load BL3x from NAND, src: 0x00010000, des: 0x01704000, size: 0x000b7c00, part: 0
NOTICE: BL31: v1.3(release):3edeb02
NOTICE: BL31: Built : 16:43:54, Apr 14 2020
NOTICE: BL31: AXG secure boot!
NOTICE: BL31: BL33 decompress pass
OPS=0x23
[Image: axg_v1.1.3494-9ec8345 2020-04-17 18:16:39 jenkins@walle02-sh]
25 0c 23 00 fc 7e 94 ad 97 9e 5a 72 80 07 60 27
bl30:axg ver: 9 mode: 0
bl30:axg thermal0
[0.015880 Inits done]
secure task start!
high task start!
low task start!
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01 (Nov 19 2021 - 22:40:09), Build: jenkins-Antminer_S19j-Pro_AMLCtrl_release_tls-12
DRAM: 256 MiB
Relocation Offset is: 0eeaf000
mmu cfg end: 0x20000000
mmu cfg end: 0x20000000
register usb cfg[0][1] = 000000000ff6cfc8
aml_i2c_init_port init regs for 0
NAND: get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
oob avail size 6
Creating 1 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000000000-0x000000200000 : "bootloader"
A revision NAND 2Gib MT29F2G08-A initialized ok
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
PLANE change!
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
aml_nand_init :oobmul=1,oobfree.length=8,oob_size=64
oob avail size 8
nbbt=20
nenv=24
nkey=32
ndtb=40
nddr=44
bbt_start=20 env_start=24 key_start=32 dtb_start=40 ddr_start=44
nbbt: info size=0x800 max_scan_blk=24, start_blk=20
nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
nbbt free list:
blockN=21, ec=-1, dirty_flag=0
blockN=22, ec=-1, dirty_flag=0
blockN=23, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
aml_nand_scan_rsv_info 1137
nbbt valid addr: 280000
aml_nand_bbt_check 1258 bbt is valid, reading.
aml_nand_read_rsv_info:446,read nbbt info to 280000
nenv: info size=0x10000 max_scan_blk=32, start_blk=24
nenv : phy_blk_addr=25, ec=0, phy_page_addr=0, timestamp=6
nenv free list:
blockN=24, ec=-1, dirty_flag=0
blockN=26, ec=-1, dirty_flag=0
blockN=27, ec=-1, dirty_flag=0
blockN=28, ec=-1, dirty_flag=0
blockN=29, ec=-1, dirty_flag=0
blockN=30, ec=-1, dirty_flag=0
blockN=31, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=32
aml_nand_scan_rsv_info 1137
nenv valid addr: 330000
nkey: info size=0x8000 max_scan_blk=40, start_blk=32
nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nkey free list:
blockN=32, ec=-1, dirty_flag=0
blockN=33, ec=-1, dirty_flag=0
blockN=34, ec=-1, dirty_flag=0
blockN=35, ec=-1, dirty_flag=0
blockN=36, ec=-1, dirty_flag=0
blockN=37, ec=-1, dirty_flag=0
blockN=38, ec=-1, dirty_flag=0
blockN=39, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=16
nkey valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nkey exist
ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
ndtb : phy_blk_addr=41, ec=0, phy_page_addr=0, timestamp=2
ndtb free list:
blockN=40, ec=-1, dirty_flag=0
blockN=42, ec=-1, dirty_flag=0
blockN=43, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=64
aml_nand_scan_rsv_info 1137
ndtb valid addr: 520000
nddr: info size=0x800 max_scan_blk=46, start_blk=44
nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nddr free list:
blockN=44, ec=-1, dirty_flag=0
blockN=45, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
nddr valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nddr exist
tpl: off 8388608, size 8388608
Creating 6 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000800000-0x000001000000 : "tpl"
0x000001000000-0x000001200000 : "misc"
0x000001200000-0x000002200000 : "recovery"
0x000002200000-0x000004200000 : "boot"
0x000004200000-0x000004700000 : "config"
0x000004700000-0x000010000000 : "nvdata"
A revision NAND 2Gib MT29F2G08-A initialized ok
MMC: aml_priv->desc_buf = 0x000000000dead560
aml_priv->desc_buf = 0x000000000deaf8a0
SDIO Port B: 0, SDIO Port C: 1
uboot env amlnf_env_read : ####
aml_nand_read_rsv_info:446,read nenv info to 330000
In: serial
Out: serial
Err: serial
aml log : internal sys error!
reboot_mode=cold_boot
[store]To run cmd[amlnf dtb_read 0x1000000 0x40000]
sub cmd dtb
new argv[1] dtb_read
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_read
arg 2: 0x1000000
arg 3: 0x40000
do_dtb_ops() read
amlnf_dtb_read: ####
warnning!!! amlnf_dtb_read dtd length too much
aml_nand_read_rsv_info:446,read ndtb info to 520000
do_dtb_ops(): 262144 bytes read : OK
aml log : R2048 check pass!
Amlogic multi-DTB tool
GZIP format, decompress...
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
Found DTB for "axg_s400_v03sbr"
gpio: pin GPIOAO_7 (gpio 7) value is 1
[MSG]usb start
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 1000140 NbrPorts 1
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... init_part() 282: PART_TYPE_DOS
1 Storage Device(s) found
[fat]Filesize is 0x25aB[0M]
[FAT_ERR]L1208,offset(0x0) + wantsz(0x6c40) > filesize(0x25a)
ERR(../drivers/usb/gadget/v2_burning/v2_common/optimus_img_decoder.c)L104:want to read 27712, but 0
[MSG]cfg[aml_sdc_burn.ini] not valid aml pkg, parse it as ini
[MSG]ini sz 0x25aB
[fat]Filesize is 0x25aB[0M]
[fat]0x:leftSz 25a < BPS 1000, gotSz 25a
=========sdc_burn_paras=====>>>
[common]
erase_bootloader = 1
erase_flash = 1
reboot = 0x1
key_overwrite = 0x0
erase_ddr_para = 0x0
[burn_ex]
package = aml_upgrade_package_enc.img
media =
[burn_parts]
burn_num = 0
<<<<=====sdc_burn_paras======
[fat]Filesize is 0x15ee8a8B[21M]
[fat]0x:leftSz c40 < BPS 1000, gotSz 6c40
[MSG]image version [0x00000002]
[MSG]SecureEnabled, use meson1_ENC
[fat]Seek 0x192300 from 0x6c40
[MSG]itemSizeNotAligned 0xd00
[MSG]align 4 mmc read... [fat]0x:leftSz 720 < BPS 1000, gotSz 7420
[MSG]Down(mem) part(dtb) sz(0x7420) fmt(normal)
[MSG]Burn Start...
[MSG]load dt.img to 0x0000000001000000, sz=0x7420
[MSG]Burn complete
[MSG]Exit before re-init
command: store exit
aml log : R2048 check pass!
Amlogic multi-DTB tool
GZIP format, decompress...
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
Found DTB for "axg_s400_v03sbr"
start dts,buffer=0000000001000000,dt_addr=0000000001010800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x3ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x3ff2800
emmc/sd response timeout, cmd1, cmd->cmdarg=0x40000000, status=0x3ff2800
EMMC init failed
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
XXXXXXX======enter NAND boot======XXXXXX
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
Amlogic multi-DTB tool
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
Found DTB for "axg_s400_v03sbr"
whole chip
do_nand(): off 0, size 268435456
Erasing at 0x0 -- 0% complete.aml_nand_erase_cmd blk 0x14 is protected
Erasing at 0x280000 -- 1% complete.aml_nand_erase_cmd blk 0x15 is protected
aml_nand_erase_cmd blk 0x16 is protected
aml_nand_erase_cmd blk 0x17 is protected
Erasing at 0xffe0000 -- 100% complete.
OK
[burn_parts]
burn_num = 3
burn_part0 = _aml_dtb
burn_part1 = boot
burn_part2 = recovery
[MSG]=====>To burn part [_aml_dtb]
[MSG]itemSizeNotAligned 0xd00
[MSG]Down(store) part(_aml_dtb) sz(0x7420) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 1
[MSG]itemSizeNotAligned 0xd00, itemSizePreload 0xd00
[fat]0x:leftSz 720 < BPS 1000, gotSz 6720
[MSG]Burn Start...
[MSG]cmd[store erase partition _aml_dtb]
0x000000000000-0x000000200000 : "bootloader"
0x000000800000-0x000001000000 : "tpl"
0x000001000000-0x000001200000 : "misc"
0x000001200000-0x000002200000 : "recovery"
0x000002200000-0x000004200000 : "boot"
0x000004200000-0x000004700000 : "config"
0x000004700000-0x000010000000 : "nvdata"
--- find_dev_and_part ---
id = _aml_dtb
[MSG]optimus_download_dtb_image:dataSzReceived=0x7420
sub cmd dtb
new argv[1] dtb_erase
do_dtb_ops(): argc 2
arg 0: amlnf
arg 1: dtb_erase
do_dtb_ops() erase
amlnf_dtb_erase: ####
erasing ndtb:
erasing valid info block: 520000
erasing free info block: 500000
erasing free info block: 540000
erasing free info block: 560000
do_dtb_ops() erase Okay
[store]To run cmd[amlnf dtb_write 0x00000000013ff300 0x40000]
sub cmd dtb
new argv[1] dtb_write
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_write
arg 2: 0x00000000013ff300
arg 3: 0x40000
do_dtb_ops() write
amlnf_dtb_save: ####
warnning!!! amlnf_dtb_save: length too much
aml_nand_save_rsv_info:685, ndtb: valid=1, pages=64
release_free_node 112: bitmap=ffffff
release_free_node 125: bitmap=fbffff
aml_nand_save_rsv_info:750,save info to 500000
do_dtb_ops(): 262144 bytes write : OK
[MSG]Burn complete
[store]To run cmd[amlnf dtb_read 0x0000000001400000 0x40000]
sub cmd dtb
new argv[1] dtb_read
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_read
arg 2: 0x0000000001400000
arg 3: 0x40000
do_dtb_ops() read
amlnf_dtb_read: ####
warnning!!! amlnf_dtb_read dtd length too much
aml_nand_read_rsv_info:446,read ndtb info to 500000
do_dtb_ops(): 262144 bytes read : OK
[MSG]VERIFY OK
[MSG]=====>To burn part [boot]
[fat]Seek 0x3295b0 from 0x199750
[MSG]itemSizeNotAligned 0xa50
[MSG]flash LOGIC partCap 0x400000000B
[MSG]Down(store) part(boot) sz(0xc2c200) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 13
[MSG]itemSizeNotAligned 0xa50, itemSizePreload 0xa50
[fat]0x:leftSz 7b0 < BPS 1000, gotSz 2b7b0
[MSG]Burn Start...
[MSG]cmd[store erase partition boot]
mtdparts_init() 848, already init
--- find_dev_and_part ---
id = boot
found boot @ 4/7do_nand(): off 35651584, size 33554432
Erasing at 0x41e0000 -- 100% complete.
OK
[burnup]Wr:Up sz 0xc2c200 to align 0x1000
[MSG]Burn complete
[MSG]Verify Start...
[MSG]To verify part boot in fmt normal
[burnup]Rd:Up sz 0x2c200 to align 0x1000
[MSG]Verify End
[MSG]VERIFY OK
[MSG]=====>To burn part [recovery]
[fat]Seek 0x1024678 from 0xf557e0
[MSG]itemSizeNotAligned 0x988
[MSG]flash LOGIC partCap 0x200000000B
[MSG]Down(store) part(recovery) sz(0x5ca200) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 6
[MSG]itemSizeNotAligned 0x988, itemSizePreload 0x988
[fat]0x:leftSz 878 < BPS 1000, gotSz c9878
[MSG]Burn Start...
[MSG]cmd[store erase partition recovery]
mtdparts_init() 848, already init
--- find_dev_and_part ---
id = recovery
found recovery @ 3/7do_nand(): off 18874368, size 16777216
Erasing at 0x21e0000 -- 100% complete.
OK
[burnup]Wr:Up sz 0x5ca200 to align 0x1000
[MSG]Burn complete
[MSG]Verify Start...
[MSG]To verify part recovery in fmt normal
[burnup]Rd:Up sz 0x1ca200 to align 0x1000
[MSG]Verify End
[MSG]VERIFY OK
[MSG]=====>To burn part [bootloader]
[MSG]itemSizeNotAligned 0x820
[MSG]Down(store) part(bootloader) sz(0xc7e00) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 1
[MSG]itemSizeNotAligned 0x820, itemSizePreload 0x820
[fat]0x:leftSz 5e0 < BPS 1000, gotSz c75e0
[MSG]Burn Start...
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 0
do_rom_ops() erase
Erasing at 0x20000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 0
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 1
do_rom_ops() erase
Erasing at 0x60000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 1
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 2
do_rom_ops() erase
Erasing at 0xa0000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 2
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 3
do_rom_ops() erase
Erasing at 0xe0000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 3
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 4
do_rom_ops() erase
Erasing at 0x120000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 4
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 5
do_rom_ops() erase
Erasing at 0x160000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 5
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 6
do_rom_ops() erase
Erasing at 0x1a0000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 6
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd rom
new argv[1] rom_erase
do_rom_ops(): argc 3
arg 0: amlnf
arg 1: rom_erase
arg 2: 7
do_rom_ops() erase
Erasing at 0x1e0000 -- 100% complete.
sub cmd bl2
new argv[1] bl2_write
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_write
arg 2: 0x13ff7e0
arg 3: 7
arg 4: 0xc000
do_bl2_ops() write
do_bl2_ops() 1
cfg.d32 0xe25004
ddrp_start_page = 0xb00 ddr_start_block = 0x2c
bl: version 1, mode 1, start 0x1000
page_per_blk = 0x40 bbt_pages = 0x1
boot_num = 4 each_boot_pages = 1024
sub cmd fip
new argv[1] fip_erase
do_fip_ops(): argc 3
arg 0: amlnf
arg 1: fip_erase
arg 2: 0
do_fip_ops() erase, base 2
Erasing at 0x9e0000 -- 100% complete.
sub cmd fip
new argv[1] fip_write
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_write
arg 2: 0x140b7e0
arg 3: 0
arg 4: 0xbbe00
do_fip_ops() write
cpy 0
sub cmd fip
new argv[1] fip_erase
do_fip_ops(): argc 3
arg 0: amlnf
arg 1: fip_erase
arg 2: 1
do_fip_ops() erase, base 2
Erasing at 0xbe0000 -- 100% complete.
sub cmd fip
new argv[1] fip_write
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_write
arg 2: 0x140b7e0
arg 3: 200000
arg 4: 0xbbe00
do_fip_ops() write
cpy 0
sub cmd fip
new argv[1] fip_erase
do_fip_ops(): argc 3
arg 0: amlnf
arg 1: fip_erase
arg 2: 2
do_fip_ops() erase, base 2
Erasing at 0xde0000 -- 100% complete.
sub cmd fip
new argv[1] fip_write
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_write
arg 2: 0x140b7e0
arg 3: 400000
arg 4: 0xbbe00
do_fip_ops() write
cpy 0
sub cmd fip
new argv[1] fip_erase
do_fip_ops(): argc 3
arg 0: amlnf
arg 1: fip_erase
arg 2: 3
do_fip_ops() erase, base 2
Erasing at 0xfe0000 -- 100% complete.
sub cmd fip
new argv[1] fip_write
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_write
arg 2: 0x140b7e0
arg 3: 600000
arg 4: 0xbbe00
do_fip_ops() write
cpy 0
[MSG]Burn complete
sub cmd bl2
new argv[1] bl2_read
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_read
arg 2: 0x000000000dec7e50
arg 3: 0
arg 4: 0xc000
do_bl2_ops() read
TODO: check fip info
sub cmd bl2
new argv[1] bl2_read
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_read
arg 2: 0x000000000dec7e50
arg 3: 1
arg 4: 0xc000
do_bl2_ops() read
TODO: check fip info
sub cmd bl2
new argv[1] bl2_read
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_read
arg 2: 0x000000000dec7e50
arg 3: 2
arg 4: 0xc000
do_bl2_ops() read
TODO: check fip info
sub cmd bl2
new argv[1] bl2_read
do_bl2_ops(): argc 5
arg 0: amlnf
arg 1: bl2_read
arg 2: 0x000000000dec7e50
arg 3: 3
arg 4: 0xc000
do_bl2_ops() read
TODO: check fip info
sub cmd fip
new argv[1] fip_read
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_read
arg 2: 0x000000000dec7e50
arg 3: 0
arg 4: 0xbbe00
do_fip_ops() read
sub cmd fip
new argv[1] fip_read
do_fip_ops(): argc 5
arg 0: amlnf
arg 1: fip_read
arg 2: 0x000000000dec7e50
arg 3: 200000
arg 4: 0xbbe00
do_fip_ops() read
[MSG]VERIFY OK
[MSG]Set upgrade_step to 1
Saving Environment to aml-storage...
uboot env amlnf_env_save : ####
aml_nand_save_rsv_info:685, nenv: valid=1, pages=32
release_free_node 112: bitmap=ffffff
release_free_node 125: bitmap=fffff7
aml_nand_save_rsv_info:750,save info to 300000
[MSG]to close image
[MSG]======sdc burn SUCCESS.
gpio: pin GPIOA_16 (gpio 56) value is 1 |
|
|
|
Hello everyone, I have an amlogic s19 j pro card which I think is totally brick following the firmware update. I used a TTL cable to analyze the outputs of the board, and here is the log. If anyone has an idea of the fatal error and how to solve it, thank you! AXG:BL1:d1dbf2:a4926f;FEAT:F0DC31BC:2000;POC:F;EMMC:800;NAND:0;READ:0;0.0;0.0;CHK:0;
sdio debug board detected
TE: 136410
BL2 Built : 10:38:43, Apr 14 2020. axg gf27ed33 - jenkins@walle02-sh
set vcck to 1100 mv
set vddee to 950 mv
init panel power
Board ID = 0
CPU clk: 1200MHz
DDR low power enabled
DDR3 chl: Rank0 16bit @ 912MHz
bist_test rank: 0 18 00 30 2b 12 45 1d 01 39 25 0b 40 00 00 00 00 00 00 00 00 00 00 00 00 721 - PASS
Rank0: 256MB-2T-13
AddrBus test pass!
NAND init
Load FIP HDR from NAND, src: 0x0000c000, des: 0x01700000, size: 0x00004000, part: 0
Load BL3x from NAND, src: 0x00010000, des: 0x01704000, size: 0x000b7c00, part: 0
NOTICE: BL31: v1.3(release):3edeb02
NOTICE: BL31: Built : 16:43:54, Apr 14 2020
NOTICE: BL31: AXG secure boot!
NOTICE: BL31: BL33 decompress pass
OPS=0x23
[Image: axg_v1.1.3494-9ec8345 2020-04-17 18:16:39 jenkins@walle02-sh]
25 0c 23 00 fc 7e 94 ad 97 9e 5a 72 80 07 60 27
bl30:axg ver: 9 mode: 0
bl30:axg thermal0
[0.015884 Inits done]
secure task start!
high task start!
low task start!
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01 (Nov 19 2021 - 22:40:09), Build: jenkins-Antminer_S19j-Pro_AMLCtrl_release_tls-12
DRAM: 256 MiB
Relocation Offset is: 0eeaf000
mmu cfg end: 0x20000000
mmu cfg end: 0x20000000
register usb cfg[0][1] = 000000000ff6cfc8
aml_i2c_init_port init regs for 0
NAND: get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
oob avail size 6
Creating 1 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000000000-0x000000200000 : "bootloader"
A revision NAND 2Gib MT29F2G08-A initialized ok
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
PLANE change!
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
aml_nand_init :oobmul=1,oobfree.length=8,oob_size=64
oob avail size 8
nbbt=20
nenv=24
nkey=32
ndtb=40
nddr=44
bbt_start=20 env_start=24 key_start=32 dtb_start=40 ddr_start=44
nbbt: info size=0x800 max_scan_blk=24, start_blk=20
nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
nbbt free list:
blockN=21, ec=-1, dirty_flag=0
blockN=22, ec=-1, dirty_flag=0
blockN=23, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
aml_nand_scan_rsv_info 1137
nbbt valid addr: 280000
aml_nand_bbt_check 1258 bbt is valid, reading.
aml_nand_read_rsv_info:446,read nbbt info to 280000
nenv: info size=0x10000 max_scan_blk=32, start_blk=24
nenv : phy_blk_addr=25, ec=0, phy_page_addr=0, timestamp=6
nenv free list:
blockN=24, ec=-1, dirty_flag=0
blockN=26, ec=-1, dirty_flag=0
blockN=27, ec=-1, dirty_flag=0
blockN=28, ec=-1, dirty_flag=0
blockN=29, ec=-1, dirty_flag=0
blockN=30, ec=-1, dirty_flag=0
blockN=31, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=32
aml_nand_scan_rsv_info 1137
nenv valid addr: 330000
nkey: info size=0x8000 max_scan_blk=40, start_blk=32
nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nkey free list:
blockN=32, ec=-1, dirty_flag=0
blockN=33, ec=-1, dirty_flag=0
blockN=34, ec=-1, dirty_flag=0
blockN=35, ec=-1, dirty_flag=0
blockN=36, ec=-1, dirty_flag=0
blockN=37, ec=-1, dirty_flag=0
blockN=38, ec=-1, dirty_flag=0
blockN=39, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=16
nkey valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nkey exist
ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
ndtb : phy_blk_addr=41, ec=0, phy_page_addr=0, timestamp=2
ndtb free list:
blockN=40, ec=-1, dirty_flag=0
blockN=42, ec=-1, dirty_flag=0
blockN=43, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=64
aml_nand_scan_rsv_info 1137
ndtb valid addr: 520000
nddr: info size=0x800 max_scan_blk=46, start_blk=44
nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nddr free list:
blockN=44, ec=-1, dirty_flag=0
blockN=45, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
nddr valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nddr exist
tpl: off 8388608, size 8388608
Creating 6 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000800000-0x000001000000 : "tpl"
0x000001000000-0x000001200000 : "misc"
0x000001200000-0x000002200000 : "recovery"
0x000002200000-0x000004200000 : "boot"
0x000004200000-0x000004700000 : "config"
0x000004700000-0x000010000000 : "nvdata"
A revision NAND 2Gib MT29F2G08-A initialized ok
MMC: aml_priv->desc_buf = 0x000000000dead560
aml_priv->desc_buf = 0x000000000deaf8a0
SDIO Port B: 0, SDIO Port C: 1
uboot env amlnf_env_read : ####
aml_nand_read_rsv_info:446,read nenv info to 330000
In: serial
Out: serial
Err: serial
aml log : internal sys error!
reboot_mode=cold_boot
[store]To run cmd[amlnf dtb_read 0x1000000 0x40000]
sub cmd dtb
new argv[1] dtb_read
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_read
arg 2: 0x1000000
arg 3: 0x40000
do_dtb_ops() read
amlnf_dtb_read: ####
warnning!!! amlnf_dtb_read dtd length too much
aml_nand_read_rsv_info:446,read ndtb info to 520000
do_dtb_ops(): 262144 bytes read : OK
aml log : R2048 check pass!
Amlogic multi-DTB tool
GZIP format, decompress...
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
Found DTB for "axg_s400_v03sbr"
gpio: pin GPIOAO_7 (gpio 7) value is 1
[MSG]usb start
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 1000140 NbrPorts 1
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
fail in cmd [fatsize usb 0 aml_sdc_burn.ini], rcode 1
ERR(../drivers/usb/gadget/v2_burning/v2_usb_burn/optimus_usb_burn.c)L41:The [aml_sdc_burn.ini] not exist in udisk
Net: sysnopsys gmac3.7
Phy 0 not found
dwmac.ff3f0000amlkey_init() enter!
amlnf_key_read: ####
amlnf_key_read key data len too much
aml_nand_ext_read_rsv_info 520: nkey is invalid! read exit![EFUSE_MSG]keynum is 4
MACADDR:02:97:ad:94:7e:fc(from chipid)
ramdump_init, add:0, size:0
usb_update_flag=
Start read misc partition datas!
[burnup]Rd:Up sz 0x440 to align 0x1000
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
recovery_status=
upgrade_step=2
[aml_i2c_xfer] error ret = -5 i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
[aml_i2c_xfer] error ret = -5 i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
[aml_i2c_xfer] error ret = -5 i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
[aml_i2c_xfer] error ret = -5 i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
CONFIG_SYSTEM_AS_ROOT: null
system_mode: 0
[imgread]szTimeStamp[2021111922403917]
[imgread]secureKernelImgSz=0xc2c000
aml log : R-2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
avb2: 0
save_power_post ...
avb2: 0
## Booting Android Image at 0x01080000 ...
reloc_addr =ded86d0
copy done
Kernel command line: init=/sbin/init
[store]Is good fdt check header, no need decrypt!
load dtb from 0x1000000 ......
Amlogic multi-DTB tool
Single DTB detected
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x0203aa00
Loading Ramdisk to 0d83b000, end 0de9d000 ... OK
Loading Device Tree to 000000000d82c000, end 000000000d83a188 ... OK
fdt_fixup_memory_banks, reg:0000000000000000
Starting kernel ...
uboot time: 4224925 us
[ 0.000000@0] Booting Linux on physical CPU 0x0
[ 0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Fri Nov 19 22:32:14 CST 2021
[ 0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
[ 0.000000@0] bootconsole [aml_uart0] enabled
[ 0.000000@0] efi: Getting EFI parameters from FDT:
[ 0.000000@0] efi: UEFI not found.
[ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000
[ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon
[ 0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB
[ 0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB
[ 0.000000@0] cma: Reserved 8 MiB at 0x000000000f800000
[ 0.000000@0] psci: probing for conduit method from DT.
[ 0.000000@0] psci: PSCIv1.0 detected in firmware.
[ 0.000000@0] psci: Using standard PSCI v0.2 function IDs
[ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000@0] psci: SMC Calling Convention v1.1
[ 0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00f753000 s64536 r8192 d29672 u102400
[ 0.000000@0] Detected VIPT I-cache on CPU0
[ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512
[ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 rootfstype=ramfs init=/sbin/init
[ 0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.000000@0] Memory: 219920K/262144K available (8764K kernel code, 1194K rwdata, 2428K rodata, 3648K init, 1018K bss, 29936K reserved, 12288K cma-reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009910000 ( 8768 KB)
[ 0.000000@0] .rodata : 0xffffff8009910000 - 0xffffff8009b80000 ( 2496 KB)
[ 0.000000@0] .init : 0xffffff8009b80000 - 0xffffff8009f10000 ( 3648 KB)
[ 0.000000@0] .data : 0xffffff8009f10000 - 0xffffff800a03aa00 ( 1195 KB)
[ 0.000000@0] .bss : 0xffffff800a03aa00 - 0xffffff800a139534 ( 1019 KB)
[ 0.000000@0] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB)
[ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf00400000 ( 4 MB actual)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB)
[ 0.000000@0] can't find symbol:arm_dma_alloc
[ 0.000000@0] can't find symbol:__alloc_from_contiguous
[ 0.000000@0] can't find symbol:cma_allocator_alloc
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] Build-time adjustment of leaf fanout to 64.
[ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000@0]
[ 0.000000@0] **********************************************************
[ 0.000000@0] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.000000@0] ** **
[ 0.000000@0] ** trace_printk() being used. Allocating extra memory. **
[ 0.000000@0] ** **
[ 0.000000@0] ** This means that this is a DEBUG kernel and it is **
[ 0.000000@0] ** unsafe for production use. **
[ 0.000000@0] ** **
[ 0.000000@0] ** If you see this message and you are not debugging **
[ 0.000000@0] ** the kernel, report this immediately to your vendor! **
[ 0.000000@0] ** **
[ 0.000000@0] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.000000@0] **********************************************************
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[ 0.000000@0] axg_aoclkc_init: register ao clk ok![ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_media: register meson media clk
[ 0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
[ 0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
[ 0.000000@0] axg_clkc_init initialization complete
[ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.008252@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
[ 0.016907@0] Console: colour dummy device 80x25
[ 0.021106@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.031586@0] pid_max: default: 32768 minimum: 301
[ 0.036439@0] thread_stack_cache_init, vmap:ffffffc00edaf600, bitmap:ffffffc00eda3000, cache page:ede0
[ 0.045773@0] thread_stack_cache_init, allocation vm area:ffffffc00edd94c0, addr:ffffff8020000000, size:20001000
[ 0.056005@0] cpu 0, vmap_stack:[ffffffc00f75c960-ffffffc00f760950]
[ 0.062304@0] cpu 0, irq_stack: [ffffffc00f753060-ffffffc00f757050]
[ 0.068603@0] cpu 1, vmap_stack:[ffffffc00f775960-ffffffc00f779950]
[ 0.074903@0] cpu 1, irq_stack: [ffffffc00f76c060-ffffffc00f770050]
[ 0.081203@0] cpu 2, vmap_stack:[ffffffc00f78e960-ffffffc00f792950]
[ 0.087503@0] cpu 2, irq_stack: [ffffffc00f785060-ffffffc00f789050]
[ 0.093803@0] cpu 3, vmap_stack:[ffffffc00f7a7960-ffffffc00f7ab950]
[ 0.100103@0] cpu 3, irq_stack: [ffffffc00f79e060-ffffffc00f7a2050]
[ 0.106465@0] Security Framework initialized
[ 0.110696@0] SELinux: Initializing.
[ 0.114428@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.128873@0] ftrace: allocating 30089 entries in 118 pages
[ 0.184510@0] sched-energy: CPU device node has no sched-energy-costs
[ 0.185326@0] CPU0: update cpu_capacity 1024
[ 0.189652@0] ASID allocator initialised with 32768 entries
[ 0.227632@0] secmon: can't fine clear_range
[ 0.227841@0] EFI services will not be available.
[ 0.231112@0] Meson chip version = RevC (25:C - 23:0)
[ 0.264979@1] Detected VIPT I-cache on CPU1
[ 0.265040@1] CPU1: update cpu_capacity 1024
[ 0.265042@1] CPU1: Booted secondary processor [410fd034]
[ 0.293040@2] Detected VIPT I-cache on CPU2
[ 0.293096@2] CPU2: update cpu_capacity 1024
[ 0.293098@2] CPU2: Booted secondary processor [410fd034]
[ 0.321116@3] Detected VIPT I-cache on CPU3
[ 0.321169@3] CPU3: update cpu_capacity 1024
[ 0.321171@3] CPU3: Booted secondary processor [410fd034]
[ 0.321262@0] Brought up 4 CPUs
[ 0.360482@0] SMP: Total of 4 processors activated.
[ 0.365390@0] CPU features: detected feature: 32-bit EL0 Support
[ 0.371427@0] CPU features: detected feature: Kernel page table isolation (KPTI)
[ 0.381994@0] CPU: All CPU(s) started at EL2
[ 0.383167@0] alternatives: patching kernel code
[ 0.388493@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
[ 0.395698@0] devtmpfs: initialized
[ 0.411161@0] DMI not present or invalid.
[ 0.411522@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.419546@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.426106@0] pinctrl core: initialized pinctrl subsystem
[ 0.432534@0] NET: Registered protocol family 16
[ 0.452056@0] cpuidle: using governor menu
[ 0.452549@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
[ 0.458169@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
[ 0.465578@0] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.471744@0] clkmsr: clkmsr: driver init
[ 0.475764@0] aml_watch_point_probe, in, wp:2
[ 0.480363@0] pstore: using zlib compression
[ 0.484708@0] console [pstore-1] enabled
[ 0.488041@0] pstore: Registered ramoops as persistent store backend
[ 0.494454@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
domain-0 init dvfs: 3
[ 0.508799@0] aml_iomap: amlogic iomap probe done
[ 0.515765@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
[ 0.517701@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[ 0.618064@0] usbcore: registered new interface driver usbfs
[ 0.618239@0] usbcore: registered new interface driver hub
[ 0.623852@0] usbcore: registered new device driver usb
[ 0.629140@0] pps_core: LinuxPPS API ver. 1 registered
[ 0.634088@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.643474@0] PTP clock support registered
[ 0.647834@0] dmi: Firmware registration failed.
[ 0.656640@0] secmon: reserve_mem_size:0x300000
[ 0.656784@0] secmon secmon: assigned reserved memory node linux,secmon
[ 0.663792@0] secmon: get page:ffffffbf00140000, 5000
[ 0.668466@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[ 0.676827@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[ 0.684735@0] NetLabel: Initializing
[ 0.686877@0] NetLabel: domain hash size = 128
[ 0.691464@0] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.696718@0] NetLabel: unlabeled traffic allowed by default
[ 0.703305@0] clocksource: Switched to clocksource arch_sys_counter
[ 0.832758@0] VFS: Disk quotas dquot_6.6.0
[ 0.832906@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.859843@1] NET: Registered protocol family 2
[ 0.860944@1] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.866103@1] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
[ 0.872770@1] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.879355@1] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.885304@1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.892046@1] NET: Registered protocol family 1
[ 0.897021@1] RPC: Registered named UNIX socket transport module.
[ 0.902435@1] RPC: Registered udp transport module.
[ 0.907326@1] RPC: Registered tcp transport module.
[ 0.912214@1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.921441@1] Unpacking initramfs...
[ 1.421674@3] Initramfs unpacking failed: junk in compressed archive
[ 1.428528@3] Freeing initrd memory: 6536K
[ 1.429403@3] hw perfevents: clusterb_enabled = 0
[ 1.431780@3] hw perfevents: cpumasks 0xf, 0x0
[ 1.436248@3] hw perfevents: cluster A irq = 7
[ 1.440814@3] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 1.450979@3] audit: initializing netlink subsys (disabled)
[ 1.454377@3] audit: type=2000 audit(1.268:1): initialized
[ 1.461681@3] workingset: timestamp_bits=62 max_order=16 bucket_order=0
[ 1.486533@3] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.489593@3] NFS: Registering the id_resolver key type
[ 1.492263@3] Key type id_resolver registered
[ 1.496569@3] Key type id_legacy registered
[ 1.501204@3] fuse init (API version 7.26)
[ 1.513161@3] NET: Registered protocol family 38
[ 1.513219@3] Key type asymmetric registered
[ 1.516465@3] Asymmetric key parser 'x509' registered
[ 1.521965@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 1.529162@3] io scheduler noop registered (default)
[ 1.534130@3] io scheduler deadline registered
[ 1.539030@3] io scheduler cfq registered
[ 1.560049@2] random: fast init done
[ 1.560149@2] random: crng init done
[ 1.560622@3] Unable to detect cache hierarchy for CPU 0
[ 1.603337@3] loop: module loaded
[ 1.604937@3] zram: Added device: zram0
[ 1.605359@3] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.612105@3] libphy: Fixed MDIO Bus: probed
[ 1.616634@3] tun: Universal TUN/TAP device driver, 1.6
[ 1.621088@3] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.629293@3] ee eth reset:Addr = ffffff80081fd008
[ 1.636806@3] meson6-dwmac ff3f0000.ethernet: no reset control found
[ 1.638730@3] stmmac - user ID: 0x11, Synopsys ID: 0x37
[ 1.644011@3] Ring mode enabled
[ 1.647210@3] DMA HW capability register supported[ 1.651953@3] Normal descriptors
[ 1.655259@3] RX Checksum Offload Engine supported
[ 1.660184@3] COE Type 2
[ 1.662783@3] TX Checksum insertion supported
[ 1.667262@3] Wake-Up On Lan supported
[ 1.671215@3] Enable RX Mitigation via HW Watchdog Timer
[ 1.679356@3] libphy: stmmac: probed
[ 1.680114@3] eth%d: No PHY found |
|
|
|
|
Hi guys, I am currently making an S9 radiator haha
I will need a firmware with immersion version for the run without fan (that easy to find) on the other hand I have a particular request, is there a firmware with a reduction by chip temp?
Example if I lower the extractor with its potentiometer, as the chip will heat up (example set at 85°c) the miner will lower its frequency to come back to the target temperature?
Thanks in advance
|
|
|
|
Hello mate, I'm sorry, between last message and know I do some research and I found on R710 7v ! (abnormal value) And at this time I did a mistake and a shortcut was created, result all my CLK signal is dead...  Any idea how to repair active system ? Cuz I already change 25M clock but she is passive so isnt her problem here.. Thanks |
|
|
|
What do you found far from good value ? CLK isn't 0.9 normal value ? and RI 1.8 ? Yes I've only one hash on this conjtrol boad (its my test board)  |
|
|
|
Hello guys! Happy new year  Today? I repair a 0 asic hashboard. To begining, it was just a RI signal problem appear on chip 30, I just replace him. Now, RI signal is good in every row (1,8v). all CLK signal and everyone are on 0,9 (lowest is 0,896v). So I guess all its okay. all each core between next row are 0,4v (lowest is 0,394v). So its okay too ? But when I run the miner, he detect 0 ASIC. In miner status I got my pool, fan, and one line after antminer shows "ASIC 0 ; IDEAL HS 0; REAL TIME HS 0;" So I guess my hashboard is detected normaly ? I check my datacable, and PSU cable, all is good cuz with another hashboard everything is great. I post my kernel log here if anyone see something... Thanks [ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364316K/507904K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 143588K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06da8ac (6987 kB)
[ 0.000000] .init : 0xc06db000 - 0xc070e380 ( 205 kB)
[ 0.000000] .data : 0xc0710000 - 0xc0757138 ( 285 kB)
[ 0.000000] .bss : 0xc0757144 - 0xc0797bfc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000290] ps7-ttc #0 at df804000, irq=43
[ 0.000590] Console: colour dummy device 80x30
[ 0.000619] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040195] pid_max: default: 32768 minimum: 301
[ 0.040400] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040419] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042581] CPU: Testing write buffer coherency: ok
[ 0.042892] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042949] Setting up static identity map for 0x4cb118 - 0x4cb170
[ 0.043169] L310 cache controller enabled
[ 0.043189] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.120983] CPU1: Booted secondary processor
[ 0.210216] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210347] Brought up 2 CPUs
[ 0.210366] SMP: Total of 2 processors activated.
[ 0.210375] CPU: All CPU(s) started in SVC mode.
[ 0.211044] devtmpfs: initialized
[ 0.213471] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214663] regulator-dummy: no parameters
[ 0.222000] NET: Registered protocol family 16
[ 0.224213] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226470] cpuidle: using governor ladder
[ 0.226483] cpuidle: using governor menu
[ 0.233836] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235350] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235363] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.235473] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.257233] bio: create slab <bio-0> at 0
[ 0.258606] vgaarb: loaded
[ 0.259301] SCSI subsystem initialized
[ 0.260318] usbcore: registered new interface driver usbfs
[ 0.260890] usbcore: registered new interface driver hub
[ 0.261165] usbcore: registered new device driver usb
[ 0.261682] media: Linux media interface: v0.10
[ 0.261845] Linux video capture interface: v2.00
[ 0.262084] pps_core: LinuxPPS API ver. 1 registered
[ 0.262096] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.262217] PTP clock support registered
[ 0.262575] EDAC MC: Ver: 3.0.0
[ 0.263762] Advanced Linux Sound Architecture Driver Initialized.
[ 0.266483] DMA-API: preallocated 4096 debug entries
[ 0.266497] DMA-API: debugging enabled by kernel config
[ 0.266565] Switched to clocksource arm_global_timer
[ 0.286418] NET: Registered protocol family 2
[ 0.287129] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.287187] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.287272] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.287316] TCP: reno registered
[ 0.287333] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.287364] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.287607] NET: Registered protocol family 1
[ 0.287946] RPC: Registered named UNIX socket transport module.
[ 0.287959] RPC: Registered udp transport module.
[ 0.287967] RPC: Registered tcp transport module.
[ 0.287976] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.287988] PCI: CLS 0 bytes, default 64
[ 0.288407] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.290401] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.292447] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.292635] msgmni has been set to 967
[ 0.293388] io scheduler noop registered
[ 0.293401] io scheduler deadline registered
[ 0.293441] io scheduler cfq registered (default)
[ 0.301973] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.301992] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.425659] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.993381] console [ttyPS0] enabled
[ 0.997645] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.005232] [drm] Initialized drm 1.1.0 20060810
[ 1.022339] brd: module loaded
[ 1.031759] loop: module loaded
[ 1.041216] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.047054] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.054769] libphy: XEMACPS mii bus: probed
[ 1.059386] ------------- phy_id = 0x3625e62
[ 1.064108] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.072911] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.079704] ehci-pci: EHCI PCI platform driver
[ 1.086936] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.093722] usbcore: registered new interface driver usb-storage
[ 1.100608] mousedev: PS/2 mouse device common for all mice
[ 1.106726] i2c /dev entries driver
[ 1.113628] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.119135] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.124999] Xilinx Zynq CpuIdle Driver started
[ 1.129893] sdhci: Secure Digital Host Controller Interface driver
[ 1.135985] sdhci: Copyright(c) Pierre Ossman
[ 1.140348] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.147195] mmc0: no vqmmc regulator found
[ 1.151205] mmc0: no vmmc regulator found
[ 1.186585] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.195273] usbcore: registered new interface driver usbhid
[ 1.200776] usbhid: USB HID core driver
[ 1.205479] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.211778] nand: Micron MT29F2G08ABAEAWP
[ 1.215740] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.221677] Bad block table found at page 131008, version 0x01
[ 1.227899] Bad block table found at page 130944, version 0x01
[ 1.233887] nand_read_bbt: bad block at 0x0000079a0000
[ 1.238977] nand_read_bbt: bad block at 0x00000b120000
[ 1.244119] 3 ofpart partitions found on MTD device pl353-nand
[ 1.249898] Creating 3 MTD partitions on "pl353-nand":
[ 1.255003] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.263057] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.270366] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.281074] TCP: cubic registered
[ 1.284313] NET: Registered protocol family 17
[ 1.289003] Registering SWP/SWPB emulation handler
[ 1.294886] regulator-dummy: disabling
[ 1.299189] UBI: attaching mtd1 to ubi0
[ 1.826183] UBI: scanning is finished
[ 1.837820] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.844875] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.851672] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.858348] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.865185] UBI: good PEBs: 1151, bad PEBs: 1, corrupted PEBs: 0
[ 1.871195] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.878306] UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1113221046
[ 1.887337] UBI: available PEBs: 0, total reserved PEBs: 1151, PEBs reserved for bad PEB handling: 39
[ 1.896533] UBI: background thread "ubi_bgt0d" started, PID 1084
[ 1.896538] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.900460] ALSA device list:
[ 1.900464] No soundcards found.
[ 1.916856] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[ 1.945945] UBIFS: recovery needed
[ 2.028323] UBIFS: recovery completed
[ 2.031991] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 2.037933] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 2.047079] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 2.056934] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.061959] UBIFS: media format: w4/r0 (latest is w4/r0), UUID E8A4479F-B15D-4C7A-964D-0F246E2BB6ED, small LPT model
[ 2.073253] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.080447] devtmpfs: mounted
[ 2.083552] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[ 2.919418] random: dd urandom read with 1 bits of entropy available
[ 3.306607]
[ 3.306607] bcm54xx_config_init
[ 4.376617]
[ 4.376617] bcm54xx_config_init
[ 8.377439] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 8.383542] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 23.195956] In axi fpga driver!
[ 23.199058] request_mem_region OK!
[ 23.202418] AXI fpga dev virtual address is 0xdf9fe000
[ 23.207556] *base_vir_addr = 0xc51e
[ 23.222030] In fpga mem driver!
[ 23.225346] request_mem_region OK!
[ 23.228978] fpga mem virtual address is 0xe2000000
[ 24.026605]
[ 24.026605] bcm54xx_config_init
[ 25.116585]
[ 25.116585] bcm54xx_config_init
[ 29.117427] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 29.123537] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
main.c:13992: log_level = 4
main.c:14019: This is XILINX board. Totalram: 507486208
main.c:14031: Detect 512MB control board of XILINX
driver-bitmain.c:1776: mmap axi_fpga_addr = 0xb6fc2000
driver-bitmain.c:1781: axi_fpga_addr data = 0xc51e
driver-bitmain.c:1797: mmap fpga_mem_addr = 0xb5dbb000
driver-bitmain.c:994: forceFreq=-1 forceFlag=0
driver-bitmain.c:1696: min work minertest[0]:912
main.c:8570: DETECT HW version=0000c51e
main.c:14064: miner ID : 8064cd8162b5885c
main.c:14089: Miner Type = S9
main.c:14101: AsicType = 1387
main.c:14104: real AsicNum = 63
main.c:14197: use critical mode to search freq...
driver-bitmain.c:1876: get PLUG ON=0x00000020
driver-bitmain.c:1946: Find hashboard on Chain[5]
main.c:2282: Check chain[5] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[5] has freq in PIC and will jump over...
main.c:9103: Chain[5] has core num in PIC
main.c:9113: Chain[5] ASIC[7] has core num=15
main.c:9113: Chain[5] ASIC[15] has core num=15
main.c:9113: Chain[5] ASIC[17] has core num=15
main.c:9113: Chain[5] ASIC[37] has core num=1
main.c:9113: Chain[5] ASIC[45] has core num=12
main.c:2282: Check chain[5] PIC fw version=0x03
main.c:9183: get PIC voltage=6 on chain[5], value=940
main.c:9349: chain[5] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[5] temp chip I2C addr=0x98
main.c:9372: chain[5] has no middle temp, use special fix mode.
main.c:13956: total_exist_chain_num = 1
main.c:9562: CRC error counter=0
main.c:9577: set command mode to VIL
main.c:9649:
--- check asic number
main.c:9745: After Get ASIC NUM CRC error counter=0
main.c:9768: set_baud=0
main.c:10693: The min freq=700
main.c:10695: set real timeout 52, need sleep=379392
main.c:12825: After TEST CRC error counter=0
main.c:14236: search freq for 1 times, completed chain = 1, total chain num = 1
board_frq_tuning.c:628: single_board_frq_tuning enter
board_frq_tuning.c:629: min_rate, des_rate, fix_volt:13800, 14000, 880
board_frq_tuning.c:254: force_freq not set, don't need tuning
main.c:14645: restart Miner chance num=2
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13927: bmminer not found= 1885 root 0:00 grep bmminer
main.c:14758: bmminer not found, restart bmminer ...
driver-btm-c5.c:12243:bitmain_c5_init: This is user mode for mining
driver-btm-c5.c:12292:bitmain_c5_init: Detect 512MB control board of XILINX
driver-btm-c5.c:12313:bitmain_c5_init: Miner Type = S9
driver-btm-c5.c:12324:bitmain_c5_init: Miner compile time: Wed Jul 31 16:18:27 CST 2019 type: Antminer S9
driver-btm-c5.c:12414:bitmain_c5_init: miner ID : 8064cd8162b5885c
driver-btm-c5.c:12571:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=6360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=6360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=6000
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=6360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=6000
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=6360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=6000
driver-btm-c5.c:13108:bitmain_c5_init: chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x00 0x4c 0x00 0x4c 0x04 0x4c 0x0c 0x4c 0x00 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x01 0x4c 0x01 0x4c 0x0f 0x4c 0x0f 0x4c 0x0f 0x4c 0x0f 0x4c 0x05 0x4c 0x09 0x4c 0x23 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=1 : 1
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J6] has backup chain_voltage=890
driver-btm-c5.c:13188:bitmain_c5_init: No scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[5] PIC fw version=0x03
driver-btm-c5.c:12195:init_exist_chain_table: total_exist_chain_num = 1
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J6] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J6] will use backup chain_voltage_pic=890 [91]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J6] get working chain_voltage_pic=91
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:4571:set_frequency: miner total rate=0GH/s ideal_total_hash_rate = 0GH/s
driver-btm-c5.c:4819:set_frequency: Miner fix freq ...
driver-btm-c5.c:5119:set_frequency: max freq = 100
driver-btm-c5.c:4162:ProcessFixFreq: totalRate = 0, fixed_totalRate = 0
driver-btm-c5.c:9604:init_uart_baud: set baud=1
driver-btm-c5.c:12103:set_working_voltage: setting to working voltage...
driver-btm-c5.c:13954:bitmain_c5_init: start thread for read temp
setStartTimePoint total_tv_start_sys=108 total_tv_end_sys=109
driver-btm-c5.c:8727:read_temp_func: bring_up_pcb_temp = -100
driver-btm-c5.c:10320:check_system_work: restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
Done check_asic_reg
Max pcb temp : -100
set FAN speed according to: temp_highest=-100 temp_top1[PWM_T]=-100 temp_top1[TEMP_POS_LOCAL]=-100 temp_change=-100 fix_fan_steps=0
FAN PWM: 0
read_temp_func Done!
CRC error counter=0
|
|
|
|
You're right, the chip 29 had problem. So I remplace it one more time, and all its good now |
|
|
|
So I checked CLK (green line from 00 to 63) and RI (yellow line from 63 to chip 28 or I lose RI from here) The chip 28 is the one I replaced as said above. But the resistances taken at the terminals of this one are correct. (CLK 0.433 CO 0.396 Ri .397 BO 0.396 RST.0316) I have tested also core to core and I found 0,446v between each chip with next row https://ibb.co/tQPLJBp |
|
|
|
Hi friend, I confirm that the RI signal stops on this chip (see picture) despite my multiple chip soldering I do not understand. When you say "jumper" it would be from where to where? https://ibb.co/ZHFH04L |
|
|
|
|
Hi guys, small question on a hashboard s9 4.21, I replaced a chip, the clock is well at 0.9 but the RI at 0v, the LDO comes out well 1.8v and 2.5v bottom pin.
All the small resistors are at the right ohm. After soldering the chip, I checked the resistors CLK30 CO30 RI30 BO30 RST30 are good in ohm. I conclude that the chip soldering is good?
Any idea where it comes from?
Thanks!
|
|
|
|
Hello ! Thanks for your awnser.. I changed my LDO to try and the thing is identical, when I plug the multimeter I have 1.80 then a micro fall to 1.599 then 1.780 and remains stabilized there and I think that is what puts me in fault RI, I imagine that it comes from a resistor yet they are all functional. At least they show a value lower than the others but proportional to 1.72 and not 1.8 I do not understand too much In the video I test a track next to it which is good and the LDO of the defective track https://youtu.be/ZvnSXT-e7l4 |
|
|
|
|
I understand, not easy without the PCB board
Thanks anyway, I tested all the components (fig 19) they are all ok. I have to buy the pick3 to flash in HEX, I don't have this item yet !
And if ever I would do a replacement of the sensor !
|
|
|
|
I sent the card in question to a friend so I don't have any logs, but I update as soon as I have a new error (I have the same one on another card) Also on another card, I have all the chips in CLK at 0.9 but the RI signal breaks level 26 25 24. And is at 0 until chip 00. I tested the LDO, they are well at 1.8v and functional. The capacitor 330u 2.5v also functional. Where can this come from according to you ? On this picture you have in grreen area CLK0.9 & RI 1.8 and in RED CLK 0.9 and RI at 0v https://i.ibb.co/xM9Zskr/unnamed.jpg |
|
|
|
|
