 Show Posts
|
|
Pages: [1]
|
Glad you got it working. As Jason said it is an issue some have seen after an upgrade. My brother has the same issue on a couple of his after an upgrade of fw..
I am far from an expert on these units and hopefully we can all learn as we move on.
I am looking into trying to port the V9 hashboards to work on z9 machines.....But that is a project that will take some time that is even if it is possible. So I may steer away from this project. If it is possible to do what I want a V9 should produce as much as 3 z9's if it is possible.
Jason you have any thoughts on porting the v9
So! I tried the firmware on one Z9 mini again from stock firmware, and it installeīs fine, but logs you out right away... now i have to do the V9 reset... somethings wrong. Don't understand what a few of you are doing wrong to get locked out. Did you ckeck to save settings when you upgrade or is the box unchecked. What batch mini? what version of posted fw with refresh or without? I and others don't understand the issue because not a single piece of code was changed from the factory file except cgminer and it has absolutely nothing to do with you logging in or getting locked out. So if there is an issue it has to do with the factory firmware not the 4 byte mod made to cgminer. With that said press and hold the reset button in...You can find it to the right of the network cable you need a pin or paperclip to press it then hold it until the red and green light flashes. It should reboot now and be back to factory settings. It must be powered on to reset it. Also there is updated information on my first post how to get in without doing all that. Well , i am upgrading like itīs suppose to be done thatīs for sure. never mind, just wanted you to know... have a nice day. You never answered my questions about what batch and what versions or whether you checked save settings.... I am beginning to think there are some trolls around every time I ask for the details all I get is "I did a recovery". I cant offer support if I don't know more information. These images have been tested over and over loading and the functions and not 1 time have I had any problems with being locked out. It is currently running on 46 minis right now without a problem. Hello and godmorgen. I can tell you for sure, i started with the fault the first time, and i was just asking a question on, if you ever seen this before nothing else, some other found a solution with a V9 reset that worked for me, somebody told me that it was something that i did wrong on all 5 asicīs, the next step for me was to install orig newest firmware and get it working again, next step was to see if it was me doing something wrong, so i downloaded the firmware from your link again on one asic and wen it was done it started up fine and stated hashing (Yes to keep setting) and working like it should. after 2 min of hashing i pressed F5 for refresh and the log on screen came up with no way to log in... itīs batch 2 and 3 - iīve tried with keep settings and donīt keep settings, i follow procedure like i always do when i spend a lot of money on something. I AM NOT A TROLL, I DONīT WANT TO TROLL, it was info i just wanted to give to you, iīm sad i canīt use your firmware and i donīt want to use Jasonīs firmware because i donīt like the fact that iīm not in control of my own hardware, so iīm back to batch 1 firmware witch is working like a charme and hashing around 15. Again, it was a kind ment infomation to you my friend. (again sorry for my english) Have a nice day. Kuno |
|
|
|
Glad you got it working. As Jason said it is an issue some have seen after an upgrade. My brother has the same issue on a couple of his after an upgrade of fw..
I am far from an expert on these units and hopefully we can all learn as we move on.
I am looking into trying to port the V9 hashboards to work on z9 machines.....But that is a project that will take some time that is even if it is possible. So I may steer away from this project. If it is possible to do what I want a V9 should produce as much as 3 z9's if it is possible.
Jason you have any thoughts on porting the v9
So! I tried the firmware on one Z9 mini again from stock firmware, and it installeīs fine, but logs you out right away... now i have to do the V9 reset... somethings wrong. Don't understand what a few of you are doing wrong to get locked out. Did you ckeck to save settings when you upgrade or is the box unchecked. What batch mini? what version of posted fw with refresh or without? I and others don't understand the issue because not a single piece of code was changed from the factory file except cgminer and it has absolutely nothing to do with you logging in or getting locked out. So if there is an issue it has to do with the factory firmware not the 4 byte mod made to cgminer. With that said press and hold the reset button in...You can find it to the right of the network cable you need a pin or paperclip to press it then hold it until the red and green light flashes. It should reboot now and be back to factory settings. It must be powered on to reset it. Also there is updated information on my first post how to get in without doing all that. Well , i am upgrading like itīs suppose to be done thatīs for sure. never mind, just wanted you to know... have a nice day. |
|
|
|
Glad you got it working. As Jason said it is an issue some have seen after an upgrade. My brother has the same issue on a couple of his after an upgrade of fw..
I am far from an expert on these units and hopefully we can all learn as we move on.
I am looking into trying to port the V9 hashboards to work on z9 machines.....But that is a project that will take some time that is even if it is possible. So I may steer away from this project. If it is possible to do what I want a V9 should produce as much as 3 z9's if it is possible.
Jason you have any thoughts on porting the v9
So! I tried the firmware on one Z9 mini again from stock firmware, and it installeīs fine, but logs you out right away... now i have to do the V9 reset... somethings wrong. |
|
|
|
Im on the road at the moment, but I am willing to try to help via team viewer at some point if you would like.
Have you tried ssh or just http?
Thanks Jason, you are kind, but i did the V9 reset and its working for me, now im looking for at firmware to unlock the freq. |
|
|
|
chipless, trying to help with this response regardless what you may think....
I have not tried chipless' firmware, but the default http login is root/root and the default ssh login is root/admin. If the password is changed via the web interface, then the ssh and web logins are synchronized.
I disagree with the comments on this being network issues (ignoring IP changes) or browser caching -- that simply doesn't happen for HTTP Authorization requests.
If you do a _full_ factory reset using the V9 procedure, the MAC address on the unit will change and your router will assign a new IP address (Incidentally, I've had the instructions on this recovery at the bottom of my first post on the firmware thread from day one for worst-case scenarios).
Unless something has changed since the version of chipless' firmware I looked at, I'm going to agree with him and say I cannot see how this would happen. If you install firmware with the 'keep settings' unchecked, all configuration is removed except for the MAC address (which means IP address is likely to stay the same, even if using DHCP; this is part of my disagreement on the network issue comments).
If we assume that the passwords are out of whack for whatever reason, then yes, the V9->Z9 recovery process will work, 100%. Personally, I'd try to look at the ssh login and see if root/admin works (and root/root, in case something wacky has happened).
@chipless - in this scenario, I've worked with the users via teamviewer to understand and resolve the issues. That may be an option if you can get one of these users to work with you. Does not take long and goes a long way towards customer satisfaction as well as knowledge gained.
@Kunolyb -- I do not completely understand your response. smarty's firmware is for the Z9 and chipless' firmware is for the Z9Mini. How and why would you have upgraded from smarty's to this one?
Thank you,
Jason
Ahh brain fart Jason i wrote this early morning, sorry as you said itīs not smartyīs, then i cant remember, but it was one to unlock til freq. but all i know is that my miniīs worked flawless no matter what before the upgrade and after the upgrade and a pc shutdown i was unable to log on. And to be absolutely clear i am thanking chiplessī for his work and iīm glad there are people like him. When we download and use costume firmware it is at our own risk, no matter what, i did just ask if he had seen this error before. So i may not understand code and my not be at "nerd" at these things, but i have really tried all that was out there to log in, i have the same user and the same password on all my asic - 4xZ9 - 4xA9 - 5xZ9mini and 2xX3, so i only upgraded 5 miniīs and they dont work? That is very strange i my world. |
|
|
|
I have working Batch 4 firmware for the z9 Mini unlocked with working temp and fan for the Batch 4 units. I am not asking for dev fee and only ask for donations if you find it helpful for your Batch 4 Z9 mini. This is a one time fix no further updates for this firmware Efudd has the furture updates covered with his projects. I am only releasing this because the fan noise on the batch 4's sucks when using batch 1 firmware. Donations Zcash only can be sent to: t1e4Dmr5RBgnWqTN2mAmZ6JzGavW7qxA4P1 THIS IS FOR Z9 Mini's ONLY WILL WORK ON ALL BATCHES 1-4 No Auto-Refresh: https://drive.google.com/file/d/1fSrEopPWO5nChvphh7zvIT_3zj4DI4t5/view?usp=sharingI am going to offer some updates but I don't believe they will be to the extent of Efudd's clocking and fan mods, mine will be mostly to the web gui options and if possible the ability to change the HTTP port thru the web gui. This will make it possible to monitor remotely thru a web browser when you have multiple units behind a router. 11/23/2018 3:48 Update: Added Auto-Refresh to the miner status page auto update status every 45 seconds With Auto-Refresh https://drive.google.com/file/d/1FioZnKLtVITpj9UfcDWlS1HnG5sVCvVV/view?usp=sharingHello, what is the password for the firmware? I can not go to the device Password is same as default user/pass root and root if you cant login clear your browsers cache. If you need to reset it press the reset for 10 seconds. I don't know know why you cant login nothing was changed that would effect the login or a factory reset. If you changed your password on the unit before the upgrade then you would use that password. nothing helps ... maybe your login and password are in the firmware? the fan works 100%, even though it was standing on my machine, and the red light flashes as if there is no Internet. When you try to login what does it do? Also check your units IP to make sure it didn't change unless you had it set to static ip. Otherwise I don't know why you are not logging in. The only thing changed was cgminer and it has nothing to do with the units login or web gui. Sounds like a ip or a pc browser issue. All the login credential were never touched everything is factory user and passwords. Bitmain has a utility called iPreporter that you can run on your pc then you press the ip button on the unit and it will send the ip to the reporter or you can look for it under devices in your router One of the first posts the user says it works fine so I don't know I tried different browsers, in the list of clients of the router ip has not changed, the name of ASIC has changed from antminer to Unknown That is a network issue of some sort. The router isn't getting the data it should be. What batch mini are you trying it on? and What version of the firmware did you last load to it? right after your firmware, I started requesting a login and password ... and before the firmware I removed the tick "Keep settings:", that is, everything should have been on the standard settings Before this was the May firmware bitmain So if you had a static ip it would default back to dhcp mode which the router then may assign a new ip to it. I had weird issues with that on the stock firmware also. You may need to reboot your router to clear its cache and show the correct ip so you can access it. Or you can download the ipreporter software from bitmain's support area and run it then press the ip report button on the front of the miner control box it will send the correct ip to the software so you can verify it. Also the reset button is in the small hole on the front while the miner is running press a pin into it for about 10-20 seconds ...you will see red and green light flash. This is still the may firmware with the cgminer replaced which has no affect on logging into it that is why I don't understand how you are locked out of it. There is no possible way the software I released can lock you out. I do know if you have it in a DMZ zone on your router you can get locked out and you have to reset it with the reset button. I don't know why this can happen I found that weird crap on the stock firmware when I was accessing it remotely. Don't know if bitmain somehow accessed it then or hacker but none of the default passwords would work until I did a reset by the front button then a few hours later it would happen again finally I took it out of the dmz zone. I found a solution to the problem, I have already restored my z9 mini https://support.bitmain.com/hc/en-us/articles/360006020914-V9-Z9-Mini-Control-Board-Program-RecoveryThanks man, i will try it when i get home  good job - and i think i will stay away from the firmware, despite the wonderful effort making it, but its not for my machines. 5 with that firmware and 5 not working. But Thanks anyway |
|
|
|
I have working Batch 4 firmware for the z9 Mini unlocked with working temp and fan for the Batch 4 units. I am not asking for dev fee and only ask for donations if you find it helpful for your Batch 4 Z9 mini. This is a one time fix no further updates for this firmware Efudd has the furture updates covered with his projects. I am only releasing this because the fan noise on the batch 4's sucks when using batch 1 firmware. Donations Zcash only can be sent to: t1e4Dmr5RBgnWqTN2mAmZ6JzGavW7qxA4P1 THIS IS FOR Z9 Mini's ONLY WILL WORK ON ALL BATCHES 1-4 No Auto-Refresh: https://drive.google.com/file/d/1fSrEopPWO5nChvphh7zvIT_3zj4DI4t5/view?usp=sharingI am going to offer some updates but I don't believe they will be to the extent of Efudd's clocking and fan mods, mine will be mostly to the web gui options and if possible the ability to change the HTTP port thru the web gui. This will make it possible to monitor remotely thru a web browser when you have multiple units behind a router. 11/23/2018 3:48 Update: Added Auto-Refresh to the miner status page auto update status every 45 seconds With Auto-Refresh https://drive.google.com/file/d/1FioZnKLtVITpj9UfcDWlS1HnG5sVCvVV/view?usp=sharingHello, what is the password for the firmware? I can not go to the device Password is same as default user/pass root and root if you cant login clear your browsers cache. If you need to reset it press the reset for 10 seconds. I don't know know why you cant login nothing was changed that would effect the login or a factory reset. If you changed your password on the unit before the upgrade then you would use that password. nothing helps ... maybe your login and password are in the firmware? the fan works 100%, even though it was standing on my machine, and the red light flashes as if there is no Internet. When you try to login what does it do? Also check your units IP to make sure it didn't change unless you had it set to static ip. Otherwise I don't know why you are not logging in. The only thing changed was cgminer and it has nothing to do with the units login or web gui. Sounds like a ip or a pc browser issue. All the login credential were never touched everything is factory user and passwords. Bitmain has a utility called iPreporter that you can run on your pc then you press the ip button on the unit and it will send the ip to the reporter or you can look for it under devices in your router One of the first posts the user says it works fine so I don't know I tried different browsers, in the list of clients of the router ip has not changed, the name of ASIC has changed from antminer to Unknown That is a network issue of some sort. The router isn't getting the data it should be. What batch mini are you trying it on? and What version of the firmware did you last load to it? Goodmorning. So the upgrade have been made from Smarassīs firmware ind it have been working flawless until i installed this firmware, it started fine, i adjusted the overclock a little and nothing was wrong, log on worked no problem right after upgrade, then i turned off the computer and went to work came back turned on the computer and it asked for the user and password, normal it just auto log on, so i tried all the things you have written og more, even a new computer, smartphone and tablets. so next step, reset, reset and another reset then factory reset, factory reset and last another factory reset, the same result. went on bitmain site to be sure thatīs its done correct, and iīm sure it was the wright way. so, after factory reset the old ip is gone and a new has come up, so im on the network and i can see the unit is reset due to i not hashing on my pool, i can find the unit on the network and i also come too the log on screen but nothing i plug in is working. (Sorry for my english iīm Danish ) Hope this makes i a bit cleare. |
|
|
|
I have working Batch 4 firmware for the z9 Mini unlocked with working temp and fan for the Batch 4 units. I am not asking for dev fee and only ask for donations if you find it helpful for your Batch 4 Z9 mini. This is a one time fix no further updates for this firmware Efudd has the furture updates covered with his projects. I am only releasing this because the fan noise on the batch 4's sucks when using batch 1 firmware. Donations Zcash only can be sent to: t1e4Dmr5RBgnWqTN2mAmZ6JzGavW7qxA4P1 THIS IS FOR Z9 Mini's ONLY WILL WORK ON ALL BATCHES 1-4 No Auto-Refresh: https://drive.google.com/file/d/1fSrEopPWO5nChvphh7zvIT_3zj4DI4t5/view?usp=sharingI am going to offer some updates but I don't believe they will be to the extent of Efudd's clocking and fan mods, mine will be mostly to the web gui options and if possible the ability to change the HTTP port thru the web gui. This will make it possible to monitor remotely thru a web browser when you have multiple units behind a router. 11/23/2018 3:48 Update: Added Auto-Refresh to the miner status page auto update status every 45 seconds With Auto-Refresh https://drive.google.com/file/d/1FioZnKLtVITpj9UfcDWlS1HnG5sVCvVV/view?usp=sharingHello, what is the password for the firmware? I can not go to the device Ohh you too?  yes...found a solution? No! iīm still having massive problems, reset, ip reset and other reset dont work. Iīm lost! |
|
|
|
I have working Batch 4 firmware for the z9 Mini unlocked with working temp and fan for the Batch 4 units. I am not asking for dev fee and only ask for donations if you find it helpful for your Batch 4 Z9 mini. This is a one time fix no further updates for this firmware Efudd has the furture updates covered with his projects. I am only releasing this because the fan noise on the batch 4's sucks when using batch 1 firmware. Donations Zcash only can be sent to: t1e4Dmr5RBgnWqTN2mAmZ6JzGavW7qxA4P1 THIS IS FOR Z9 Mini's ONLY WILL WORK ON ALL BATCHES 1-4 No Auto-Refresh: https://drive.google.com/file/d/1fSrEopPWO5nChvphh7zvIT_3zj4DI4t5/view?usp=sharingI am going to offer some updates but I don't believe they will be to the extent of Efudd's clocking and fan mods, mine will be mostly to the web gui options and if possible the ability to change the HTTP port thru the web gui. This will make it possible to monitor remotely thru a web browser when you have multiple units behind a router. 11/23/2018 3:48 Update: Added Auto-Refresh to the miner status page auto update status every 45 seconds With Auto-Refresh https://drive.google.com/file/d/1FioZnKLtVITpj9UfcDWlS1HnG5sVCvVV/view?usp=sharingHello, what is the password for the firmware? I can not go to the device Ohh you too? |
|
|
|
hello
Downloaded your firmware for the z9 mini for all 5 miniīs and now i am unable to log on, the user and password are not working on any of them, have you had this problem before?
Kuno
ps iīm not even able to reset to factory...
The only time I have ever had a login issue was when I needed to close my browser and clear the browser temp files. The reset is power on the unit wait about 30 sec to a min then hold the reset button in until the fault and normal light flash ---about 10-20 seconds pressing the button. Thanks man, will try that now. |
|
|
|
|
hello
Downloaded your firmware for the z9 mini for all 5 mini´s and now i am unable to log on, the user and password are not working on any of them, have you had this problem before?
Kuno
ps i´m not even able to reset to factory...
|
|
|
|
|
Watch out for scammers guys! Just got a email from Jeremy C saying that I'm in and told me to transfer 4300 in crypto just like that.
|
|
|
|
Hello Bitcoin talk. Happy new year! I'm new here and just wanted to say thx for all the info here, seems like there a lot of people interested in the Baikal giant B, and I'm also in that boat 😀 So, if it is possible I would like to be added to the waiting list for one peace of the Baikal giant B miner. Thanks Kunolyb@msn.com From Denmark |
|
|
|
|
