 Show Posts
|
|
Pages: [1]
|
|
Yes, def. a scam. Looked fishy right from the start with the MN auctions. Pitty for people bidding for MN up to 1btc lol...
Github has been deleted.
|
|
|
|
|
The pool only reports effective hashrate there's usual some difference, sometimes it's lower, sometimes it's higher. Best way is to look at earnings per 24h not hashrates.
|
|
|
|
|
Double check if you have everything setup correctly on the mining software, 20 mins is usually more than enough to see an update on the dashboard/worker status.
|
|
|
|
|
You don't need to create the worker as the pool will do it automatically but that can take a lot of time, however your shares are still counted towards your balance. But you can manually create your workers (I did) and usually within a few minutes you get hashrate/shares info.
|
|
|
|
|
@miningpoolhub
Trying to get litecoin exchanged to Ethereum, it just sits on the Auto Exchange wallet indefinitely. Other coins go through just fine...
Any news on fixing the european hub servers resolving to IP's with over 250+ ms from Europe?
|
|
|
|
These are IPS of the mining pool servers, check ping for each and choose one that works best for you
europe.equihash-hub.miningpoolhub.com 139.162.138.168
europe.equihash-hub.miningpoolhub.com 172.104.180.119
europe.equihash-hub.miningpoolhub.com 172.104.106.153
europe.equihash-hub.miningpoolhub.com 172.104.127.76
europe.equihash-hub.miningpoolhub.com 139.162.73.35
europe.equihash-hub.miningpoolhub.com 172.104.189.59
That being said, you should probably use fqdn as it will return the fastest server for your area, if I'm not mistaken.
I'm in Europe, only server under 250ms is 139.162.138.168 at 50ms for me and it's not accepting connections at the moment. Try us-east.ethash-hub.miningpoolhub.com, it pings ~180ms from where I'm at (East Europe) I've been using it as a backup, i'm from Western Europe so I get ~100ms, however, I think it's getting hammered because the European servers are all messed, and miners are switching over to the us... |
|
|
|
These are IPS of the mining pool servers, check ping for each and choose one that works best for you
europe.equihash-hub.miningpoolhub.com 139.162.138.168
europe.equihash-hub.miningpoolhub.com 172.104.180.119
europe.equihash-hub.miningpoolhub.com 172.104.106.153
europe.equihash-hub.miningpoolhub.com 172.104.127.76
europe.equihash-hub.miningpoolhub.com 139.162.73.35
europe.equihash-hub.miningpoolhub.com 172.104.189.59
That being said, you should probably use fqdn as it will return the fastest server for your area, if I'm not mistaken.
I'm in Europe, only server under 250ms is 139.162.138.168 at 50ms for me and it's not accepting connections at the moment. |
|
|
|
|
I'm pretty sure they're just doing round robin DNS, as I had one rig on one of the true European servers and other rigs on the Japanese or whatever they are... So it depends, which you get on the first dns resolution.
It's happening on the eth-hub aswell, I already posted multiple times about this, I tweeted MPH, and zero response until now. I would like to keep my rigs on MPH, but i've been testing etherminer the last couple days and will do rerun of nanopool as the support on MPH on this issue has been non-existant.
|
|
|
|
With regards to my post above: I had to manually add *all* workers to *all* algorithms pages in {ALGO} > Workers > Worker name/password. Having them defined in the "Hub Workers" page was not sufficient ... none of them were showing up on any of the algorithm stats pages.
To the pool OP: you really should fix the European server issue. At least 5 servers that respond to europe.equihash-hub.miningpoolhub.com are in fact in Japan with a ping of 300ms from Europe.
I already reported it here but no response or fix. It is happening with the Ethash servers aswell, they have some kind of DNS round robin and a few IP's that are returned are being routed through Japan. Alternatively you can use us-east that has a latency of around 100ms (depending on where you are in Europe). However, I just went back to Ethermine for now... |
|
|
|
There's something wrong with the european Equihash hub servers as apparently they're getting routed to somewhere else: Pinging europe.equihash-hub.miningpoolhub.com [172.104.180.119] with 32 bytes of data:
Reply from 172.104.180.119: bytes=32 time=259ms TTL=48
Reply from 172.104.180.119: bytes=32 time=260ms TTL=48
Reply from 172.104.180.119: bytes=32 time=259ms TTL=48
Reply from 172.104.180.119: bytes=32 time=259ms TTL=48 Pinging us-east.equihash-hub.miningpoolhub.com [45.79.223.173] with 32 bytes of data:
Reply from 45.79.223.173: bytes=32 time=108ms TTL=47
Reply from 45.79.223.173: bytes=32 time=107ms TTL=47
Reply from 45.79.223.173: bytes=32 time=109ms TTL=47
Reply from 45.79.223.173: bytes=32 time=108ms TTL=47 Ethash hub latency: Pinging europe.ethash-hub.miningpoolhub.com [172.104.252.26] with 32 bytes of data:
Reply from 172.104.252.26: bytes=32 time=40ms TTL=56
Reply from 172.104.252.26: bytes=32 time=41ms TTL=56
Reply from 172.104.252.26: bytes=32 time=40ms TTL=56
Reply from 172.104.252.26: bytes=32 time=40ms TTL=56
|
|
|
|
All fine here: ZEC: 01/03/18-11:47:28 - New job from europe.equihash-hub.miningpoolhub.com:17023 |
|
|
|
|
Hi,
I've been mining Equihash and auto-exchanging to ZClassic, has been working fine.
Today I changed the auto-exchange to Ethereum and manually went into my Zclassic Wallet and clicked on the transfer button in order to get them Auto-Exchanged to Ethereum.
At the moment the Zclassic wallet has 0 balance both regular and deposited for auto-exchange. I still see Bitcoin Gold and Zencash with a bit of balance waiting to be auto-exchanged.
But the ZClassic just disappeared...
Should I just wait or something is wrong?
Thx.
|
|
|
|
|
